Weider Club C4800 Support Question
Weider Club C4800 Support Question
Find answers below for this question about Weider Club C4800.Need a Weider Club C4800 manual? We have 1 online manual for this item!
Question posted by Missyspence on June 16th, 2020
Lat Cable #62 188” Snapped On Weider C4800.
Where can I buy a replacement for LAT cable #62 188 1/4 " for Weider C4800?
Current Answers
Answer #1: Posted by INIMITABLE on June 16th, 2020 4:21 AM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,088,520
Member since:
April 3rd, 2020 Points: 2,088,520
Check here to look for Wider spare parts
https://www.searspartsdirect.com/model/1xfijolb9b-001490/weider-wesy47330-weight-system-parts
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Related Weider Club C4800 Manual Pages
English Manual - Page 2
... YOU BEGIN 5 ASSEMBLY 6 ADJUSTMENTS 26 WEIGHT RESISTANCE CHART 28 CABLE DIAGRAMS 29 TROUBLE SHOOTING 31 EXERCISE GUIDELINES 32 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of ICON Health & Fitness, Inc.
2 Remove the PART IDENTIFICATION CHART and PART LIST...
English Manual - Page 4
...force.
13. Replace any commercial, rental, or institutional setting.
4. Keep hands and feet away from the weight system when performing an exercise that the cables are properly ... designed to protect the floor.
5. Always disconnect the lat bar from moving parts.
8. Never release the butterfly arms, leg lever, lat bar, leg press, or accessories while weights are adequately...
English Manual - Page 5
...the weight system. ASSEMBLED DIMENSIONS: Height: 82 in . Length: 60 in . Shroud Backrest
Lat Bar High Pulley Station
AB Pulley Station Butterfly/Press Arm
Weight Stack Seat Leg Press
Curl Pad... system (see the front cover of the body.
If you for selecting the versatile WEIDER® CLUB C4800 weight system. To help you want. Whether your goal is WESY47330.
The model number...
English Manual - Page 6
... step. ASSEMBLY
Make Assembly Easier for Yourself
Everything in this stage you will attach the cables and pulleys that connect the arms to the weights. The parts needed for the Weight ... walk around the weight system as possible, we have been pre-attached. If a part is completed. Cable Assembly-During this manual is enough room to see if it . Select a Location for each stage to...
English Manual - Page 13
...location, and around a 100mm Pulley (38). Wrap the Lat Cable (62) under a 100mm Pulley
19
(38). Attach the Leg Press Plate (15) to hold the
Cable in the welded tube must be between the Leg Press ...99), two 12.5mm Spacers (69), and an M10 Nylon Locknut (101).
18. Identify the Lat Cable (62). Make sure the Cable Trap is in step 15.
16.
Note: The four M10 Thick Spacers (70) must be...
English Manual - Page 14
...(38) and down through the Top Frame. Route the Lat Cable (62) over a 100mm Pulley (38). Thread an M12 Nut (58) all the way onto the Lat Cable (62). Attach the Pulley to the Double "U"-bracket (42) with...), two 12.5mm
Spacers (69), and an M10 Nylon Locknut (101).
38
62 101
99 69
69 99
80
21. Route the Lat Cable (62) up through the Top Frame (9). Set a 50mm Washer (95) on a ...
English Manual - Page 15
... (99),
99 9
and an M10 Nylon Locknut (101).
101
99
63 80
26. Make sure the Cable Trap is oriented to the indicated hole in the groove of the Pulley.
27. Attach the Pulley inside the... (58) all the way onto the Upper Short Stack Cable (63). Route the Upper Short Stack Cable (63) over a 100mm Pulley (38). Route the Upper Short Stack Cable (63) up through the Top Frame (9) and over...
English Manual - Page 16
...) around a 100mm
31
Pulley (38). Wrap the Butterfly Cable (67) around a 100mm
32
Pulley (38). Attach the Pulley to the Butterfly Frame (... M10 Washers (99), and an
M10 Nylon Locknut (101).
31. Wrap the Butterfly Cable (67) around a 100mm Pulley (38). Identify the Butterfly Cable (67). Attach the
30
Cable inside the Butterfly Upright (2) with an M10 x 213mm Bolt (92), two
M10 Washers...
English Manual - Page 17
...M8 Nylon Locknut (87).
87 100
67 87
37. Note: Do not complete-
Route the Butterfly Cable (67) through the
34
Butterfly Upright (2) and over a
37
100mm Pulley (38).
Note: The following ... the Base (1) with an M10 x 45mm Bolt (51). ly tighten the Locknut; Attach the Pulley and a Long Cable Trap (68) to the
Double "U"-bracket (42) with an M10 x 50mm
Bolt (81) and an M10 Nylon ...
English Manual - Page 18
...M8 Nylon Locknut (87).
42
100 87
43. Wrap the Lower Short Stack Cable (64) around a 100mm Pulley (38). Wrap the Lower Short Stack Cable (64) under a 90mm Pulley (39). Attach the Pulley to the Leg...an M10 x
45mm Bolt (51). Identify the Leg Press Cable (65). Attach the Pulley and a Large Cable Trap (68) to the bottom of the Lower Short Stack Cable (64) to the Base (1) with an M10 x 45mm...
English Manual - Page 19
...two M10 Washers (99), two 12.5mm Spacers (69), and an M10 Nylon Locknut (101). Wap the Leg Press Cable (65) around a 90mm
45
Pulley (39). Attach the Pulley inside the Leg Lever with an M10 x 50mm
Bolt ...(55), an M10 Washer (99), and an M10 Nylon Locknut (101). Make sure the large ball on the Cable is oriented to the "U"-bracket (40) with an M8 Washer (100) and an M8 Nylon Locknut (87)....
English Manual - Page 20
... with an M10 x 50mm Bolt (81) and an M10 Nylon Locknut (101). Attach the Pulley and a Long Cable Trap
(68) to the Butterfly Upright (2) with an M10 x 45mm Bolt (51) and an M10 Nylon Locknut... Note: This step is routed over a 100mm Pulley
51
(38). Make
sure the Cable Trap is oriented to hold the Cable in the groove of the weight system. Note: The following steps are shown from the...
English Manual - Page 21
... x 45mm Bolt (51) and an M10 Nylon
Locknut (101).
2 101
51 38
56. Wrap the Ab Cable (66) under a 100mm Pulley
53
(38). Route the Ab Cable (66) over a 100mm Pulley
54
(38). Wrap the Ab Cable (66) over a 100mm Pulley (38) and through the Butterfly Upright (2).
Attach the Pulley to the indicated...
English Manual - Page 26
...Clips (75).
Use the WEIGHT RESISTANCE CHART on page 32 for the exercise to the Ab Cable (66) at any worn parts immediately. For some exercises, the 16" Chain (73) should be performed. Do not use...Lock (61) until it engages the Pad Tube (33) in the right weight stack.
Replace any pulley station in the correct starting position for important information about how to adjust the ...
English Manual - Page 28
The other numbers refer to the 6 lb. Note: The actual resistance at each exercise station. top weights. weight plates. Weight resistance shown for the butterfly arm station is for each station may vary due to the 12.5 ... Top" and "Right Top" refer to the 12.5 lb. "Bottom" refers to differences in individual weight plates as well as friction between the cables, pulleys, and weight guides.
English Manual - Page 29
... the proper routing of the Lat Cable (62), Upper Short Stack Cable (63), Lower Short Stack Cable (64), Leg Press Cable (65), Ab Cable (66), and Butterfly Cable (67). Use the diagrams to make sure that the cable traps do not touch or bind the cables.
3 1
4
Upper Short Stack Cable (63) Length: 82 3/4 inches
2 2
5
6
6 4 5
4 3
5 Leg Press Cable (65) Length: 119 inches
2
1
1 3
Lower...
English Manual - Page 30
2
Lat Cable (62)
Length: 188 1/4 inches
1
6
4
7 5
3
8 8
3
4 2
6
Ab Cable (66) Length: 217 inches
5
7
1
1 2
5
4 6
Butterfly Cable (67) Length: 107 1/2 inches
7
30
English Manual - Page 31
... the Pulley and the
Cable Trap between a
set of the Cable far- Slack can be replaced, see ORDERING REPLACEMENT PARTS on the end of the Pulley Plates
with the Bolt and Locknut. If the cables need to hold the cable in the Pulley
2
Plates (41). To tighten the Lat Cable (62) or the Upper Short Stack Cable (not shown), first...
English Manual - Page 39
... without notice. See the back cover of the user's manual for information about ordering replacement parts. PART LIST-Model No. WESY47330
R1003B
Key No. Qty. Description
1
1
... Square Bushing
57
6
58
2
59
2
60
1
61
1
62
1
63
1
64
1
65
1
66
1
67
1
68
... Lat Cable Upper Short Stack Cable Lower Short Stack Cable Leg Press Cable Ab Cable Butterfly Cable Long Cable...
English Manual - Page 41
... you . This warranty does not extend to any implied warranties of the product (WEIDER® CLUB C4800 weight system)
3.
Accordingly, the above limitation may not apply to freight damage,...ICON Health & Fitness, Inc. Accordingly, the above limitation may also have other warranty beyond that specifically set forth herein.
This warranty extends only to replacing or repairing, ...
Similar Questions
I'm Having Cable Routing Problems
I bought a Weider Pro 4100 machine pre built, it had one or two cables out of place but even when I ...
I bought a Weider Pro 4100 machine pre built, it had one or two cables out of place but even when I ...
(Posted by hc12900 3 years ago)
How To Use Butterfly Function On Weirder Club C4800
(Posted by nicolelatta90 7 years ago)
How To Connect The Butterfly Component Of My C4800
i would like to know how to change my c4800 from a press to butterfly
i would like to know how to change my c4800 from a press to butterfly
(Posted by hardheart13 7 years ago)
How To Install Cable And Pulley On Weider Pro 4850
can you help me install new weider pro 4850 cable and pulley?
can you help me install new weider pro 4850 cable and pulley?
(Posted by verrolburnett 8 years ago)
How Does The Butterfly Function Work On The Weider C4800
(Posted by rchillin10 10 years ago)