Weider Pro 3550 Support Question
Weider Pro 3550 Support Question
Find answers below for this question about Weider Pro 3550.Need a Weider Pro 3550 manual? We have 1 online manual for this item!
Current Answers
Answer #1: Posted by Odin on April 1st, 2023 9:24 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,640
Member since:
April 10th, 2010 Points: 41,236,640
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Weider Pro 3550 Manual Pages
English Manual - Page 1
Patent Pending
Visit our website at www.weiderfitness.com
new products, prizes, fitness tips, and much more! MST
CAUTION
Read all precautions and instructions in the space above for future reference. Save this equipment.
As a manufacturer, we will ...
English Manual - Page 2
... YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 22 WEIGHT RESISTANCE CHART 24 TROUBLESHOOTING 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of ICON Health & Fitness, Inc.
2 WEIDER is a registered trademark of this manual. Remove the PART...
English Manual - Page 3
.... Do not use of this manual and in the locations shown on a level surface. Make sure that does not use only. Make sure that the cables are exercising, stop immediately and begin cooling down.
16.
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precautions
before using...
English Manual - Page 4
... a decal attached to tone your body, build dramatic muscle size and strength, or improve your benefit, read this manual for selecting the versatile WEIDER® PRO 3550 weight system. until 6 p.m. The model number is to the weight system (see the front cover of this manual carefully before calling.
VKR* Arm Lat Bar...
English Manual - Page 5
... to the weight stacks. Tightening Parts
Tighten all parts as shown in the drawings. Mountain Time. Cable Assembly-During this stage, you assemble them, unless instructed to make assembly easier, we have divided ... size, the weight system should be assembled in the location where it will attach the cables and pulleys that there is enough room to walk around the weight system as you assemble...
English Manual - Page 11
...the parts bags labeled "CABLE ASSEMBLY" and "PULLEYS." Locate the VKR High Cable (74), which is... identifying the
19
cables. Attach the eyelet end of the Cable inside of two ... 2 3/4" Bolts (101)
and two 3/8" Nylon Jamnuts (113).
31
CABLE ASSEMBLY
19. IMPORTANT: Refer to the Butterfly Frame (47) with soapy water...26) to the Cable Identification
Chart on the other end. Slide an Inner Cap...
English Manual - Page 12
... the Butterfly Top Frame with 3/8" x 1 3/4" Bolt
(93) and a 3/8" Nylon Locknut (87).
74
78
93
87 61
6 87
93 119
74
22.
Wrap the VKR High Cable (74) under the Top Weight.
5
Place a 1/2" Washer (1) on the other end. Remove the preattached 3 1/2" Pulleys (78 [only one end and a ball on top of the...
English Manual - Page 13
... with the 3/8" x 2" Bolt (100) and the 3/8" Nylon Locknut (87). Make sure that the Cable Trap is turned to the indicated
bracket on the Left Butterfly Arm (25) with the Bolt and a...
5/16" x 1" Shoulder Bolt (103) and a 5/16" Nylon
Locknut (86).
13
86 69
103 70
25 Attach the Cable to hold the Cable in the Pulley Plates (63) with a 5/16" x 2 1/2" Bolt
(59), two 5/16" Washers (90), and a...
English Manual - Page 14
... the Butterfly Upright (3) with a 3/8" x 1 3/4" Bolt (93) and a 3/8" Nylon Locknut (87).
69
78
30. Wrap the Butterfly Cable (69) over a "V"-pulley (55). Wrap the Butterfly Cable (69) over a "V"-pulley (55).
28
Attach the Pulley and a Long Cable Trap (102) to the Pivot Bracket
31
(70) on the Butterfly Upright (3)
with a 5/16" x 1"
Shoulder Bolt (103...
English Manual - Page 15
...119 91 75
113 3
35
93
87
62
75
78
15 32. Make sure that the Large Cable Trap is 98 1/2" long and has an eyelet on one end and a threaded pin on the ... (89), and a 3/8" Nylon Locknut (87) as shown.
34. Route the Leg Lever Cable (75) under a 4 1/2" Pulley (119). Route the eyelet end of the Cable through the Seat Upright (9) and attach it to the indicated side of the Seat Upright (9) ...
English Manual - Page 16
... 3 1/2" Pulley (not shown) from the "U"-bracket (64).
36
Attach the end of the Leg Lever Cable (75) to the indicated brack-
Attach the Pulley to the "U"-bracket (64) with 3/8" x 1 3/4"... 3/8"
Nylon Locknut (87).
16
87 78
72 93
120
93 87
61 72
78 Route the eyelet
end of the Cable.
75
64 97 34
37. Attach a 3 1/2" Pulley (78) to the Offset Double "U"- bracket (61) with...
English Manual - Page 17
... 3/4" Bolt
(93) and a 3/8" Nylon Locknut (87).
78 72 87
42. Wrap the VKR Low Cable (72) over a 3 1/2" Pulley
42
(78). et on the Short Base (2) with a 3/8" x 2" Bolt (100) ... Nylon
Locknut (87).
Attach the Pulley and a Cable Trap (68)
between the indicated holes in the groove of Weights (44). Make sure that the Cable Trap is
turned to the indicated brack- Attach the...
English Manual - Page 18
... holes in the groove of
45
the Short Base (2) with a 3/8" x 3 1/4" Bolt
(96) and a 3/8" Nylon Jamnut (113). Wrap the VKR Low Cable (72) over a 3 1/2" Pulley
47
(78). Attach the Pulley and a Cable Trap (68)
44
between the indicated brackets
on the Squat Slider (38) with a 5/16" x 2 1/2" Bolt (59),
two 5/16" Washers (90), and...
English Manual - Page 19
...120
6 87
93 119 73
50.
Press the two Knee Pad Caps (109) into the ends of the Squat Cable (73). Slide two Short Pads (20) onto the Leg Lever (10).
50
51 109
19
4 73
118... screw the end of holes from the top in the Seat Upright (9). Wrap the Squat Cable (73) under the Top Weight. 48. ond set of the Cable (73) two full turns into the square hole in the indicated brack-
Place a 1/2"...
English Manual - Page 21
... and slide the Squat Bracket (37) down onto the Squat Slider (38). Make sure that the cables move smoothly, find and correct the problem. See TROUBLESHOOTING on page 26 and 27 of the Squat ...
114
115 38
58. Turn the Squat
Backrest (35) so that the four screw holes are not properly installed, they may be explained in ADJUSTMENTS, beginning on page 22 of the 3/8" Nylon Locknuts (87) used ....
English Manual - Page 22
... lat bar, row bar, or handle, make sure that both "L"-pins w/Tethers (60) are in the correct starting position for the exercise to the Lat Cable (88) or the VKR Low Cable (not shown) in the same way. The weight setting of each part of the Weight Pin is in 10-pound increments...
English Manual - Page 24
... below shows the approximate weight resistance at each weight station may vary due to differences in individual weight plates as well as friction between the cables, pulleys, and weight guides. Note: The actual resistance at each butterfly arm. "Top" refers to the 10-pound weight plates.
English Manual - Page 25
... with
the Bolt and Nylon Locknut.
Remove the cable and re-install it is slack in several ways:
See drawing 1. If there is first used . Screw the
end of the weight stacks. See drawing 3. Reattach the Pulley and the Cable
4
Trap between
a set of cable used on the
end of holes closer to be...
English Manual - Page 31
... Pad Cap 5/16" x 2 1/2" Carriage Bolt Inner Cap w/Hole Pin w/Tether 3/8" Nylon Jamnut 1/4" x 3/4" Screw Adjustment Knob 3/4" x 1 1/2" Inner Cap 1 1/4" Square Inner Cap 1/2" Nut 4 1/2" Pulley Long Base Large Cable Trap 3/8" x 3 3/4" Bolt Knee Rest Bumper 3/4" Spacer 2" x 2 1/2" Inner Cap Butterfly Arm Stop User's Manual Exercise Guide
Note: "#" indicates a non-illustrated part.
English Manual - Page 33
...costs of removal or installation or other consequential damages ... of the product (WESY38322)
• The NAME of the product (WEIDER® PRO 3550 weight system)
• The SERIAL NUMBER of the product (see the front cover... is in its authorized service centers.
ICON is authorized by ICON. ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 191730 R1102B
...
Similar Questions
I Have A Weider Pro 3550 And I Need A Cable For The Press And Butterfly Arm.
(Posted by runnenwb 2 years ago)
Weirder Pro 575 Replacement Cables
where can I order the replacement cables for this machine.
where can I order the replacement cables for this machine.
(Posted by Lilhoss 3 years ago)
What Is The Part # For The Vkr Low Cable (72) On The Weiderpro 3550
(Posted by fgcoker 3 years ago)
What Did The Weider Pro 3550 Cost New?
I'm trying to sell one that I got in a trade. It is like new.
I'm trying to sell one that I got in a trade. It is like new.
(Posted by leewild 7 years ago)
Video For Cable Installation
I'm looking for a Video showing how to install the Cables and Pulleys for my Weider 3650
I'm looking for a Video showing how to install the Cables and Pulleys for my Weider 3650
(Posted by Timzshadow 10 years ago)