iRobot Verro 500 Support Question
iRobot Verro 500 Support Question
Find answers below for this question about iRobot Verro 500.Need a iRobot Verro 500 manual? We have 1 online manual for this item!
Question posted by probert9 on July 7th, 2022
Le Robot N Avance Plus.
La batterie s allume et se referme, comme un cour circuit.
Current Answers
Answer #1: Posted by Odin on July 7th, 2022 4:21 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,690
Member since:
April 10th, 2010 Points: 41,236,690
See the Trbleshooting section starting at https://www.manualslib.com/manual/514720/Irobot-Verro-600.html?page=19#manual, and reference a Problem reflecting your precise difficulty.
If the issue persists or if you require further advice, you may want to consult the company: use the contact information at https://www.contacthelp.com/irobot.
If the issue persists or if you require further advice, you may want to consult the company: use the contact information at https://www.contacthelp.com/irobot.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Answer #2: Posted by SonuKumar on July 8th, 2022 8:16 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,617,810
Member since:
May 9th, 2021 Points: 16,617,810
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related iRobot Verro 500 Manual Pages
Product Manual - Page 2
...the pool. A Ground Fault Current Interrupter (GFCI) must be consistent with water.
iRobot Verro Owner's Manual The connection to turn the Power Supply OFF and unplug it must be used ... (electrical code). Please keep the plug away from the water. Always remember to the branch circuit should not be supplied through a Ground Fault Current Interrupter outlet. The unit must be replaced ...
Product Manual - Page 3
... not in the socket on the Power Supply. Operating the cleaner out of its cleaning cycle. Do not use Verro in water.
Retain the safety and operating instructions for 15 to lift Verro from the pool. www.irobot.com Do not use the floating power cord to 20 minutes following the end...
Product Manual - Page 4
...power cord from becoming twisted and to improve coverage of the entire pool. (p. 8)
Tip Store Verro in loss of the pool. Tip iRobot recommends using the mesh filter bag (available separately at ...maintain traction, particularly on the walls of warranty.
The fine filter bag is not kept clean, Verro will not clean properly and will result in a dry place out of direct sunlight at www....
Product Manual - Page 5
Table of Contents
Anatomy 6 Parts List 7 Using Verro 8 - 10 How Verro Works 11 Cleaning the Filter Bag 12 - 13 Maintenance and Adjustment 14 - 18 Troubleshooting 19 - 20 Customer Care 21
www.irobot.com
Product Manual - Page 8
... twisting the floating power cord and ensure more even coverage.
2 Uncoil the floating power cord and spread it over the surface of the water.
3
Place Verro in the water and rock it is right side up and level.
4 Place the Power Supply (transformer) at least 3.5 meters /12 feet from side to...
Product Manual - Page 9
the light on the Power Supply will illuminate and Verro will vary based on
the Power Suppy. ON: Green button turns robot ON.
Warning: A Ground Fault Current Interrupter (GFCI) must be...collar clockwise to lock it into a GFCI outlet. To
stop Verro before the end of the cleaning cycle will start Verro; OFF: Red button turns robot OFF. Never leave the Power Supply plugged in one way. ...
Product Manual - Page 10
... the Power Supply every time you remove the cleaner from the water. Never leave the Power Supply plugged in use the handle to cool.
Using Verro (cont...)
8
When Verro has finished cleaning the pool it will stop automatically and the Power Supply light will drain from...
Product Manual - Page 11
... size. (For comparison, the period at the end of this sentence is more than 500 microns in only 60 - 90 minutes.
How Verro Works
Verro has a powerful motor that they can be vacuumed up through the bottom of the robot and out through the top helps Verro maintain traction on the pool bottom and walls.
Product Manual - Page 12
... panel by pushing the two locking tabs toward the sides of the water pumped through the filter bag to prevent scratching the robot's shell). If the filter bag becomes clogged, Verro will not be able to clean as effectively and may have trouble moving along the bottom and up the walls properly...
Product Manual - Page 13
... this does not remove all visible dirt, machine wash the bag using cold water on the support bars. Label
8 Replace filter bag assembly in the robot. 9 Replace the bottom cover. Do not machine dry.
7 Turn the filter bag so that the felt surface is clear.
www.irobot.com 13
Make sure...
Product Manual - Page 14
.... The Power Supply is riding on its side tracks instead of on the brushes. Changing the Brushes Eventually, Verro's brushes will be happy to provide assistance.
1 Unplug the Power Supply. (Please keep your robot looking good for years to come. Remove the four screws that you have any difficulty, please call our...
Product Manual - Page 15
... brushes are difficult to remove, soak them in water for 20 minutes.
8 Push the new brushes onto the wheel tubes.
9 Place the brushes back in robot, reinstalling the drive belts and drive tracks over the end hubs.
10 Replace the side plate.
11 Reattach the four screws. Side Plate
5 Note the...
Product Manual - Page 16
If you have difficulty climbing the walls of the robot, remove the four screws that hold on its drive wheel. They will be happy to provide assistance.
1 Place Verro upside down on a towel and remove the filter bag assembly. (p. 12)
2 On each side of the pool. Side Plate
3 Remove the side plates. 4 Remove...
Product Manual - Page 17
... to travel around your hand, walk away from the Verro. www.irobot.com 17 However, if the cord tangles or kinks and will not lie properly ... twisted, use the Detangler to untwist it. Detangler location
1 Unplug the floating power cord from the Power Supply. 2 Place Verro so that it untwists as you can walk away from getting twisted. Changing the direction of the water, it may be necessary...
Product Manual - Page 18
.... Cleaning the Impeller
Outlet Top Propeller
1 Unplug the floating power cord from the Power Supply. 2 Remove the screws that attach the outlet top to the robot. 3 Lift off the outlet top. 4 Clean any debris from the propeller and shaft. 5 Replace the outlet top and reinstall the screws. 18 iRobot...
Product Manual - Page 19
... bag. (p. 12) cleaned
The pump impeller is Clean the impeller. (p. 18) fouled
Verro does not climb the walls of the handle before troubleshooting any other additives.
Troubleshooting
Many... fabric softeners, bleach, or any problem.
is fully seated, turn off Verro's Power Supply and unplug it . (p. 9)
Verro is not cleaning properly
The filter bag needs to be Clean the filter ...
Product Manual - Page 20
... to untwist the cord. (p. 17) stuck on which it may
get caught.
Troubleshooting (cont...)
Problem
Verro does not cover the entire pool
Likely cause
What to do
The filter bag needs to be Clean the filter...the long sides of the pool
Ensure the floating power cord is preventing Verro
Position the Power Supply 12 feet away from the center
from objects on its twisted floating power ...
Product Manual - Page 22
....727.9077 or visit store.irobot.com
*See registration card for details. All rights Reserved.
3000a.07 All rights reserved. SAVE 15% on all accessories.*
Verro Accessories: Mesh Filter Bag Fine Filter Bag iRobot Verro Storage Caddy
Visit our website to change. iRobot is a registered trademark and...
Similar Questions
Irobot Verro 500 Outlet Cover
IRobot Verro 500 outlet cover
IRobot Verro 500 outlet cover
(Posted by Anonymous-174235 10 months ago)
Parts For Irobot Verro 500
hiWhere can I get the part #9 called the filter screen for my pool vacuum cleaner IRobot Verro 500. ...
hiWhere can I get the part #9 called the filter screen for my pool vacuum cleaner IRobot Verro 500. ...
(Posted by alain1reg 1 year ago)
I Robot 500 Pool Cleaner
My pool cleaner goes one direction hits the wall and then wont go back the other direction any more....
My pool cleaner goes one direction hits the wall and then wont go back the other direction any more....
(Posted by trevorerhardt 2 years ago)
Tune Up For Irobot Verro 500
Where if possible can i send my iRobot Verro 500 to be tuned up ?If this is not possible do you have...
Where if possible can i send my iRobot Verro 500 to be tuned up ?If this is not possible do you have...
(Posted by lynedenis 2 years ago)
Robot Verro 500
i want service center Canada Montreal h1a4c3.thanks
i want service center Canada Montreal h1a4c3.thanks
(Posted by jacquespep 5 years ago)