Makita AN454 Support and Manuals
Get Help and Manuals for this Makita item
This item is in your list!
View All Support Options Below
Free Makita AN454 manuals!
Problems with Makita AN454?
Ask a Question
Free Makita AN454 manuals!
Problems with Makita AN454?
Ask a Question
Makita AN454 Videos
Popular Makita AN454 Manual Pages
AN454 Instruction Manual - Page 2
...instructions)
SPECIFICATIONS
Model:
AN454
Air pressure
0.49 - 0.83 MPa (70 - 120 PSIG)
Nail length (L) x Shank diameter (D)
L: 19 mm - 45 mm x D: 3.05 mm (L: 3/4″ - 1-3/4″ x D: 0.120″)
Nail... Tool modification
1. The tool should not be modified unless authorized in the tool manual or approved in fully pulled position.
5. Refer to a source whose pressure potentially ...
AN454 Instruction Manual - Page 3
... fasteners as a working with fasteners when any maintenance or repairs;
3. Do not point tool toward yourself or anyone whether it setting.
6. Do not use common sense when working implement.
...high pressure inside the tool, failure to re-contact work surface only.
13. Ask Makita's Authorized service centers for periodical inspection of tool. Do not lift, pull or lower tool by striking...
AN454 Instruction Manual - Page 4
... nailing frequency may cause a decrease in this instruction manual may result in serious injury to follow the safety rules stated in
the driving capability of the tool.
4 ENGLISH
PARTS DESCRIPTION
1
3
INSTALLATION
...Makita Authorized or Factory Service Centers, always using Makita replacement parts. Trigger 2.
Failure to tool operator or persons in the vicinity. Nailing...
AN454 Instruction Manual - Page 5
.... Hook
► 1 . If the nailer accidentally drops, it may result in the B direction, decrease the air pressure. Adjusting depth of nailing
CAUTION: Always return the trigger and disconnect the hose before adjusting the depth of nailing.
1
A
To insure maximum performance, install an air set to assure continuous, efficient nailing operation. If nails cannot be fired a couple of...
AN454 Instruction Manual - Page 6
... 2. Set the nailer so that the contact element will depress both the exposed shingle and previous row of nails when loading nails in desired position. If the tool is designed for hanging the tool temporarily. Adjusting plate 2. Shingle guide 3. Hole The hook is convenient for consistent shingle exposure. NOTICE: Set the coil support plate according to the nail...
AN454 Instruction Manual - Page 7
...installed onto the air fitting. Coil support plate 2. Graduation 3.
Select this mode, set the actuation mode selector to reach the feed claw. Contact actuation mode: You can drive one nail...
nail coil is set to the position for 1-2 seconds after checking to the position. Place other uncoiled nails on feeder body.
Place the
first nail in the driver channel and the second nail ...
AN454 Instruction Manual - Page 8
...prudent manner and in solvent and remove tar and dirt with all local and national code requirement.
8 ENGLISH Failure to perform inspection or maintenance, always return the trigger and... the nailer becomes jammed, do so causes poor nail feeding. Avoid storing nails in solvent. Cleaning and removal of the tool may result.
Hammer 2. NOTICE: Never use deformed nails or nail strip....
AN454 Instruction Manual - Page 9
.... Air filter
9 ENGLISH Maintenance of nailer
Always check the tool for more details regarding these accessories, ask your Makita tool specified in this manual. With tool disconnected, make daily inspection to wear quickly.
1
2
Maintenance of the contact element and trigger. Do not use with your local Makita Service Center.
• Nails
• Air hose
• Safety...
AN454 Instruction Manual - Page 10
...Makita's Factory or Authorized Service Centers. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of ONE YEAR from state to you.
10 ENGLISH If inspection shows the trouble is caused by others: • repairs...by defective workmanship or material, Makita will repair (or at our option, replace) without charge. THIS DISCLAIMER ...
AN454 Parts Breakdown - Page 2
Model AN454 Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part... SEPARATER O-RING 67 O-RING 35 DRIVER COMPLETE FRONTCUSHION HOUSING COMPLETE INC. 29... ONE TOUCH JOINT HOOK FLAT WASHER 5 SPRING WASHER 5 HEX.SOCKET HEAD BOLT M5X16 TRIGGER BASE SPRING PIN 3-28 SPRING PIN 3-28 O-RING 15 TRIGGER VALVE GUIDE O-RING 17
1 PC. 1 PC. 1 PC. 4 PC. 4 PC. 2 2 1 1 1 PC. 1 PC. 1 1 PC. 1 PC. 1...
AN454 Parts Breakdown - Page 3
... CASE COMPRESSION SPRING 10 STOP RING E-3 SLEEVE4 TRIGGER COMPLETE INC. 62-64 SPRING PIN 2.5-16 IDLER TRIGGER STEELBALL3 COMPRESSIONSPRING2 LEVER4 O-RING 41 O-RING 4 DRIVER GUIDE ASSY INC. 71-82 DRIVER GUIDE COMPLETE PIN 4 FEEDING CLAW COMPRESSION SPRING 6 O-RING 8 URETHAN RING 3 PISTON O-RING 17 COMPRESSION SPRING 7 RUBBER RING 16 CUP WASHER 5 RETAINING RING R-24 FRONT...
AN454 Parts Breakdown - Page 4
... M4X10 HOLDER CAP MAGAZINE GUARD L SPRING WASHER 4 PAN HEAD SCREW M4X10 FLAT WASHER 5 HEX.SOCKET HEAD BOLT M5X30 ADJUSTER PLATE HEX.SOCKETHEADBOLTM4X20 SPRING WASHER 4 SINGLE GUIDE RING 9 LEVER PLATE LOCK PLATE SPRING WASHER 4 PAN HEAD SCREW M4X10 HEX.BOLT M6X20 URETHAN RING 3 DOOR PIN 4 DOOR COVER HEX.SOCKET HEAD BOLT M4X8...
AN454 New Tool Flyers English - Page 1
...Saw (5007F)
1
2
3
All specifications subject to stock on hand. Patent and Trademark Office. NTF-0418 MA-4311-18
4
5
makitatools.com 1-3/4" COIL ROOFING NAILER
NEW TOOL OVERVIEW
AN454
PRODUCT HIGHLIGHTS
PERFORMANCE
Large carbide inserts on nose piece for long lasting performance
EFFICIENCY
Easy, one-step open, adjustable canister system for control over nailing operation • Powerful...
Makita AN454 Reviews
Do you have an experience with the Makita AN454 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Makita yet.
Earn 750 points for your review!