Makita XLT02Z Support and Manuals
Get Help and Manuals for this Makita item
View All Support Options Below
Free Makita XLT02Z manuals!
Problems with Makita XLT02Z?
Ask a Question
Free Makita XLT02Z manuals!
Problems with Makita XLT02Z?
Ask a Question
Popular Makita XLT02Z Manual Pages
XLT02Z Instruction Manual - Page 1
INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Cordless Angle Impact Wrench Boulonneuse d'Angle à Chocs sans Fil Llave de Impacto
XLT02
014172
IMPORTANT: Read Before Using. IMPORTANTE: Leer antes de usar. 1 IMPORTANT: Lire avant usage.
XLT02Z Instruction Manual - Page 2
... the warnings refers to follow the warnings and instructions may differ from heat, oil, sharp edges or moving parts. Cluttered or
dark areas invite accidents. 2. ... (RPM)
0 - 2,000 /min
Impacts per minute
0 - 3,000
Max. ENGLISH (Original instructions)
SPECIFICATIONS
Model
XLT02
Capacities
Standard bolt High tensile bolt
M4 - Carrying power tools with earthed or grounded surfaces such...
XLT02Z Instruction Manual - Page 3
... with water. in this instruction manual may differ depending upon the kind or size of battery pack may affect the power tool's operation. Service 28. Power tool use ...Hold power tool by a qualified
repair person using the tool in use ) replace strict adherence to a rotating part of fire when used . Check the torque with specifically designated battery packs. A wrench...
XLT02Z Instruction Manual - Page 4
...careful not to water or rain. Overcharging shortens the battery service life. 3. Charge the battery cartridge once in locations ...not incinerate the battery cartridge even if it . 4. SAVE THESE INSTRUCTIONS.
Always insert it from the tool while sliding the button on the front of the cartridge.
• To install the battery cartridge, align the tongue on (1) battery charger, (2) ...
XLT02Z Instruction Manual - Page 5
...that causes it may damage the tool. • When not operating the tool, always set the reversing switch lever to see the source of light
directly.
012128
Lithium-ion batteries ...before
operation. • Use the reversing switch only after switch lever release, have tool serviced at a Makita service center. Release the switch lever to draw an abnormally high current. CAUTION: • Always...
XLT02Z Instruction Manual - Page 6
... hex bolt to do so may cause the breakage of the tool or personal injury.
1. To install the hook, insert it into place. To remove, loosen the screw and then take it locks ...angle head to the bolt or nut. Tooth
2
008496
To install the socket, push it onto the anvil of the tool. Hook (Accessory)
CAUTION: • When installing the hook, tighten the screw firmly. Anvil
2
2
008335...
XLT02Z Instruction Manual - Page 7
...The proper fastening torque may damage the
bolt/nut or socket. If you can see the red part on and fasten for 15 minutes before proceeding with a torque wrench. 1. Before starting your ...check the torque with a fresh battery cartridge. If not, it is operated continuously until the red part cannot be seen. Insert it
locks in the figures. When the battery cartridge is shown in place...
XLT02Z Instruction Manual - Page 8
... the above limitation may also have been made to state. It is caused by Makita Authorized or Factory Service Centers, always using Makita replacement parts. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF "MERCHANTABILITY" AND "FITNESS FOR A SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM OF THIS WARRANTY. This Warranty gives you...
XLT02Z Parts Breakdown - Page 2
... PC. 1 PC. 1 PC. 1 PC. 1 PC. 2 PC. 1 1 0 1 PC. 1 PC. Model XLT02Z Parts List
A = Standard Equipment 〇= Circuit Diagram
Item#
Part# Description
001
187889-4
001 C10 263005-3
001 C20 803B00-9
001 C21 802J50-9
001 D10
002
265995-6
003
815L76-4
004
...
040 C21 802J50-9
040 D10
042
424044-0
043
231990-8
HOUSING SET RUBBER PIN 6 CAUTION LABEL CAUTION LABEL INC. 40 TAPPING SCREW ...
Makita XLT02Z Reviews
We have not received any reviews for Makita yet.