ZyXEL EOC350 Series Support and Manuals
Get Help and Manuals for this ZyXEL item
View All Support Options Below
Free ZyXEL EOC350 Series manuals!
Problems with ZyXEL EOC350 Series?
Ask a Question
Free ZyXEL EOC350 Series manuals!
Problems with ZyXEL EOC350 Series?
Ask a Question
Popular ZyXEL EOC350 Series Manual Pages
User Guide - Page 6
... Configuration ...59 10.6.2 Restore Configuration ...60
Chapter 11 Telnet ...61
11.1 Overview ...61 11.2 Config Telnet Server ...61
11.2.1 Command Format ...61 11.2.2 Generic Command Sets ...62
Chapter 12 SNMP ...71
12.1 Overview ...71
Chapter 13 Troubleshooting...73
13.1 Power, Hardware Connections, and LEDs 73 13.2 EOC350-TS Access and Login ...74
6
EOC350 Series User's Guide
User Guide - Page 16
... used over the Coax connections.
Bootcode
This shows the version of the system firmware.
System Firmware
This shows the version of the program code that consists of different types of the device. If you forget your last configuration.
16
EOC350 Series User's Guide System MAC Address
This shows the MAC address used over the Ethernet connections...
User Guide - Page 18
... Setup
Use this menu to reset the system to enable and configure the HTTP server.
View Log
Use this menu to put new firmware in to see the current system time.
Upload Firmware
Use this sub-menu to the management interface. After login, the main window shows the System Info screen.
18
EOC350 Series User's Guide...
User Guide - Page 19
EOC350 Series User's Guide
19
Your EOC350-TS automatically computes the subnet mask based on the IP address you enter, so do not change this field unless you want to assign to your network in dotted decimal notation, for example 255.255.255.0 (factory default). CHAPTER 3
System Setup
3.1 Overview
This chapter describes how to configure the...
User Guide - Page 20
... IP address of the first DNS server the EOC350-TS checks to add source information and validate IP/MAC bindings granted by DHCP servers. Select DHCP Option 82 and IP Source Guard to resolve IP addresses. Click Apply to pass DHCP traffic without modification.
Select Disable to save your settings.
20
EOC350 Series User's Guide
User Guide - Page 36
... to obtain the connection speed and duplex mode that both ends support. Click Apply to the main EP Management screen.
36
EOC350 Series User's Guide Choices are Auto, 10M/Full, 10M/Half, 100M/Full, ...100M/Half.
If this port. Click Back to return to save your settings. Select On to enable...
User Guide - Page 42
The backup configuration file will be useful in case you back up (save) the EOC350-TA's current configuration to a file on your previous settings.
42
EOC350 Series User's Guide Once your EOC350-TA is configured and functioning properly, it is highly recommended that you need to return to back up your configuration file before making configuration changes...
User Guide - Page 48
... Click Administration > HTTP Setup to save your settings.
48
EOC350 Series User's Guide Chapter 6 Administration Figure 45 Administration > Telnet Setup
The following table describes the items in this screen.
Figure 46 Administration > HTTP Setup
The following screen. Table 38 Administration > HTTP Setup
LABEL
DESCRIPTION
HTTP Server Select whether the HTTP service is disabled or...
User Guide - Page 49
... name. Figure 48 Administration > SNMP Trap Server
EOC350 Series User's Guide
49
Location
Type a location.
Chapter 6 Administration
6.6 The SNMP Setup Screen
Use this screen to show the following screen.... Table 39 Administration > SNMP Setup
LABEL
DESCRIPTION
SNMP
Select whether the SNMP service is disabled or enabled. Click Apply to save your settings.
6.7 The SNMP Trap Server ...
User Guide - Page 53
... is updated from. EOC350 Series User's Guide
53 Server
Secondary SNTP Server
Type the address of the primary SNTP server. Click Apply to configure when and where the time is updated via the Simple Network Time Protocol. Click System Time > SNTP Setup to show the following table describes the items in this screen to save your settings.
User Guide - Page 61
...to apply settings to be configured via the telnet console.
the console idle timer is also applicable to and parameters. Figure 66 Administration > Telnet Setup
Note: ...i.e. This format is 10 minutes (600 seconds).
11.2.1 Command Format
The following table describes some common parameter formats for 5 minutes; EOC350 Series User's Guide
61
CHAPTER 11
Telnet
11.1 Overview...
User Guide - Page 62
... including passwords. This stops all settings to be diagnosed
62
EOC350 Series User's Guide Reset all service for EoC interface. Setup DHCP ...firmware/driver types, 'n', where n=0~12'.
• n=0: System bootcode (termination system bootloader) • n=1: System firmware (termination system OS) • n=2: Termination system EoC driver • n=3: termination adapter EoC driver...
User Guide - Page 65
... 'private'
EOC350 Series User's Guide
65 Chapter 11 Telnet
Table 50 Generic Telnet Commands (continued)
COMMANDS
ARGUMENTS [ ] IS OPTIONAL
passwd
[name]
-o
-n
ping
reboot rmep service
[-n ] [-w ] [-l ] IP address
-m
[-s [-c ] [-p ] [-t ] ]
showep
[-f] [-n ] [-m ]
showlog showmaster
snmp
[-c ] [-p ] [-n ] [-t ] [-l ] [-r ] [-w ]
DESCRIPTION
Change user's password.
Users can...
User Guide - Page 67
...set to the default 00-0000-00-00-00
EOC350 Series User's Guide
67 Chapter 11 Telnet
Table 50 Generic Telnet Commands (continued)
COMMANDS
ARGUMENTS [ ] IS OPTIONAL
swqosq
[-t ]
[-p ]
swqosrate
swqostc
swsmac
[-m ] [-c ]
DESCRIPTION
Display or setup... Q3/Q2/Q1/Q0 service weight 8/4/2/1
• mix: Q3 is invalid if N >= 3125 (>200Mbps)
Display or setup the QoS configuration for TCP...
User Guide - Page 79
....htm
EOC350 Series User's Guide
79 Any replacement will consist of a new or re-manufactured functionally equivalent product of equal or higher value, and will , at www.us.zyxel.com ...magnetic, optical, chemical, photocopying, manual, or otherwise, without notice. This warranty is subject to receive e-mail notices of firmware upgrades and information at www.zyxel.com for global products, or ...
ZyXEL EOC350 Series Reviews
We have not received any reviews for ZyXEL yet.