Campbell Scientific CR10 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific CR10 manuals!
Problems with Campbell Scientific CR10?
Ask a Question
Free Campbell Scientific CR10 manuals!
Problems with Campbell Scientific CR10?
Ask a Question
Popular Campbell Scientific CR10 Manual Pages
CR10 Measurement and Control - Page 15
...CR10 Operator's Manual 4. The CR10 Prompt Sheet
PCTOUH is very similar Campbell Scientific's 21X and CR7 dataloggers.
The user accesses the CR10 with the portable CR1OKD Keyboard Display or with a CRl0 willhelp the learning process, so dont just read to complete a basic understanding of the CRl0 operation are the Programming Sections l-3, the portions of each programming instruction...
CR10 Measurement and Control - Page 24
Campbell Scientific's PC208 Datalogger Support Software is available for loading the program into the datalogger or on the mode the CR10 is in and is broken into the display Advance to next instruction in program table ("1 , *2, *3) or to next Output Array in Final Storage (.7) Back up to previous instruction in program table or to previous Output Array in Final Storage...
CR10 Measurement and Control - Page 28
...the CR10, purchase the Campbell Scientific Thermocou Reference, ModelCRl0TCR (Section 13.4) and make the reference temperature measurement with Output Instruction
77. The CR10 would automatically advance through a polynomialfit to the low input. Enter 1 and advance to the first stored temperature. The Data Storage Pointer (DSP) is at the same time. Advance to fourth program instruction...
CR10 Measurement and Control - Page 54
... to a specific purpose and are availabb to execute if the comparison is used to end of program table - The wind speed rose is computed using the Histogram Instruction 75, and...regardless of the outcome of the Program Control Instructions have a command code parameter which can be indexed to be manually toggled from the keyboard in the instruction is set high
and the test condition of...
CR10 Measurement and Control - Page 58
Program Gontrol Instruction Memory and Execution Times
INSTRUCTION
83 IF CASE SECTION 3. INSTRUCTION SET BASICS
TABLE 3.9-4.
CR10 Measurement and Control - Page 66
... transfer, but will NOT be tolerated during setup and check-out operations, the recorder requires 4 alkaline ... jacks on the wiring panel.
range volume setting is recommended for transferring programs via tape (refer to Appendix B)
The ...previously supplied with the CR10. Two are not compatible with the CR21 datalogger is generally successful, Campbell Scientific recommends the use of...
CR10 Measurement and Control - Page 71
...CR10 to allow the user to Severalcarriage returns (CR) must be
optional.
o
monitor data in
by hand) interrogating or programming the CRl0 via a computer/terminal.
The shorter transmission times for error detection. Campbell Scientific... computer/terminal and to set ' the
9Rl9is. varid characters are covered in Section 6 and in the American Standard Code for the devices.
The...
CR10 Measurement and Control - Page 82
... serial port is supported by the CR10.
Make sure that the computer/terminal is transmitted). lf the computer/terminal is set to 8 data bits and even or odd parity, communication cannot be displayed once if it is not transmitted, or twice if it . The most compatibles come with a jumper block. Campbell Scientific's TERM program (part of the...
CR10 Measurement and Control - Page 89
...PROGRAMMING EXAMPLES
temperatures of the scan rate. The program listed below is a continuation of the Pulse Count Instruction
(Configuration Code...to Ground (G). Young Model 121O2D Cup Anemometer, with a photochoPPer transducer produces a pulse output which revolves with a Configuration Code of previous example)
...by the CR10's Pulse Count Instruction.
AC power or back-up batteries should...
CR10 Measurement and Control - Page 115
... the output interual, this total is zeroed. Program Table 1 sets the Output Flag low
after zeroing the location where the normaltotal is set . To provide comparison, this example, Subroutine...tipping bucket rain gage.
The CR10 willcomplete whatever instruction it is executing, execute the subroutine, and then resume executing the table. The value in Instruction 92.
The subroutine adds 0....
CR10 Measurement and Control - Page 189
... average of the automatic calibration in applications where: 1) the CR10 is exposed to automatic calibration is set of the 19 input locations, the CR10 has a hardware problem or needs factory calibration.
13-23 Program table overruns are replaced each time that the instruction is stable enough to complete. Instruction 24 calibration is compiled that the program table is executed.
CR10 Measurement and Control - Page 199
... to switch external power to be used to power various sensors, it is
*25V. In this problem, the sensor power ground and the CR10 ground should be made . Campbell Scientific's CM10 and CM6 Tripods come complete with Program Control Instructions 83 through a grounding rod.
One line is for excitation voltage, the other is for use of...
CR10 Measurement and Control - Page 206
...: Increments by a Program Control Instruction. MANUALLY INITIATED: Initiated by the user, usually with CR10 Program lnstructions, parameters are numbers or codes which are entered to do. The Array ends when the Output Flag is time to Final Storage takes place when the Output Flag has been set by 1 with the CR10. The results of that instruction in this category...
CR10 Measurement and Control - Page 230
... analog OV-3, 13-2 Checksum 5-2 Clock Example of setting OV-l7 SeVdisplay time ("5 Mode) 1-2 CM6/CM10 Tripods grounding protection 14-6 Common mode range 13-3,14-7 Communicating with the CR10 OV-8 Via telemetry 5-1 With external peripherals 4-1 Communication Protocol OV-8,6-7,5-2 Troubleshooting 6-7 Compiling Data 1-4 Errors 3-9 Program 1-2 Computation of Running Average 8-1 Computer Conngcting to...
CR10 Measurement and Control - Page 234
... 3-1 Functionalmodes OV-l0 Instruction format OV-l1 Key definition OV-l0 Logical constructions 3-4 Manualcontrol of program execution 1-3 Maximum program size 1-5 Overrange detection 3-2 Overview of programming 8-2
Rain gauge, Tipping Bucket Connecting to CR10 7-1
R
Rainfall intensity, Example of lnstruction Set 3-1 Program memory 1-5 Remote 5-4 Save/load programs (.D Mode) 1-9 Sequence OV...
Campbell Scientific CR10 Reviews
We have not received any reviews for Campbell Scientific yet.