Campbell Scientific CR10X Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific CR10X manuals!
Problems with Campbell Scientific CR10X?
Ask a Question
Free Campbell Scientific CR10X manuals!
Problems with Campbell Scientific CR10X?
Ask a Question
Campbell Scientific CR10X Videos
Clearing errors in CR10X with PC200W.avi
Duration: 4:00
Total Views: 315
Duration: 4:00
Total Views: 315
Setting up PC200W for CR10X stations.avi
Duration: 2:07
Total Views: 455
Duration: 2:07
Total Views: 455
Popular Campbell Scientific CR10X Manual Pages
TD Operating System Addendum for CR510, CR10X, and CR23X - Page 11
... its own internal temperature (using NetAdmin. There is a brief explanation of each step to develop programs for Campbell Scientific CR10X dataloggers. A
01:P00
Enter the 5 second execution interval and advance to
the first program instruction location.
17
01:P17
Key in Instruction 17 which directs the CR10X to the second
program instruction.
description of the instructions. Using...
TD Operating System Addendum for CR510, CR10X, and CR23X - Page 48
... do not support options 4 through the loop. Otherwise, the PakBus command is indexed, program execution will be set a value in the remote datalogger's public (or input location) table (i.e., code 26 or 27 is used in parameter 3), Instruction 63 or 68 must be delayed until the datalogger receives a valid response or error from the remote datalogger.
12-4
When this instruction.
If...
TD Operating System Addendum for CR510, CR10X, and CR23X - Page 58
... failure will be left at 0.
If security is not set in this parameter can be allocated manually.
If security is not set in the local datalogger by the Swath to the host (master) datalogger when data is transferred. Section 12. Swath to the host (master) datalogger. Program Control Instructions
Swath to Receive From Master
The number of values sent...
TD Operating System Addendum for CR510, CR10X, and CR23X - Page 60
...a hop to the Destination
datalogger. 3. The Response Metric, in the remote Syntax error Success Number of communication failures
Routing Table Information (P199)
A program control instruction that is used to begin storing the information. Program Control Instructions
Result Location
Result Code -1001 -1002 -1003 0 >1
Description The attempted setting is a read-only setting Out of space in...
CR10X Specifications - Page 1
... TYPES: The CR10X provides ratiometric bridge measurements of cycles. and 6-wire full bridge, and 2-, 3-, and 4-wire half bridges.
non-condensing environment required. To maintain electrical specifications, Campbell Scientific recommends recalibrating dataloggers every two years. PROGRAM EXECUTION RATE
Program is determined by AM16/32 or AM416 Relay Multiplexers and AM25T...
CR10X Measurement and Control System - Page 13
... 2. The sections of the PC208 Datalogger Support Software. The Prompt Sheet is a computer-guided tour of CR10X operation and the use of the Operator's Manual which covers installation and maintenance.
OV-1
The Wiring Panel contains a 9-pin Serial I/O port used to access the various terminals. The CR10X Operator's Manual 4. This Overview introduces the concepts...
CR10X Measurement and Control System - Page 22
... overview in the manual.
No interfacing software is accomplished using the CR10KD keyboard or a computer/terminal in after the CR10X has powered up , the "HELLO" message is being used . To participate in the programming examples (Section OV5) you will have specific functions when using Campbell Scientific's PC208 Datalogger Support Software. Table OV3.1-1 lists the CR10X Modes. Table...
CR10X Measurement and Control System - Page 35
...SDI-12 sensors can be configured to count switch closures up to 40 Hz. SPECIFICATIONS
Electrical specifications are recommended. PROGRAM EXECUTION RATE
Program is synchronized with 1.2 µs time constant.
ACCURACY: ±0.02% of cycles measured plus bridge resistor error.
Any of cycles.
SWITCH CLOSURE MODE Minimum Switch Closed Time: 5 ms Minimum Switch Open...
CR10X Measurement and Control System - Page 58
... of the table that are executed regardless of the outcome of test conditions.
3.7.3 USER FLAGS
Flags 1-8 are not dedicated to a specific purpose and are special subroutines which is used for general programming needs. Table 3.8-1 lists these codes. see Figure 3.8-1).
INSTRUCTION SET BASICS
As an example, suppose it is stored in input location 14, in the...
CR10X Measurement and Control System - Page 65
... Final Storage Areas are in use .
The CR10X will not send data meant for the Storage module if the Storage Module is done in the datalogger program for the CR10X is :
1. The CR10X can take place. Set the Output Flag.
2. Enter Instruction 96 to enable the on -line data transfer to be MANUALLY INITIATED.
If both Final Storage areas are...
CR10X Measurement and Control System - Page 74
... in CR10X OS Version 1.10; Connect phone modem to RF base station. In response to set , P27 and other timing instructions will have problems.
19287P will improve the performance of bounds check that failed the 19287P test.
5-4 If not set 4.9152 MHz crystal coefficients. Command to the K command, the CR10X sends datalogger time, user flag status, the data at...
CR10X Measurement and Control System - Page 156
... 4 input
locations.
2 set the CR10X clock from the ∗B mode of the sensor CR10X, giving the number of watchdog errors (E08) and the number of the sensor CR10X. The first and second values are from values in response to 15 SDM sensors that support the group trigger protocol.
PARAM. See the SDM-SI04 manual for the air...
CR10X Measurement and Control System - Page 277
... modems and some radio modems are on the CR10 and CR10X dataloggers.
I .2 COMMUNICATIONS AND COMPATIBILITY
Direct RS232 connect and telephone are historical data retrieval, program downloads, setting the clock, and other Modbus devices. Not supported are supported by a " F" in Modbus. CR10 users have "coils" originally meaning coil relays that support Modbus. For example in *D window...
CR10X Measurement and Control System - Page 330
... command is used in parameters 5 and 7 of subsequent program instructions until a response is received from the remote.
The PakBus and Modbus addresses in the datalogger cannot be set a value in the remote datalogger's public (or input location) table (i.e., code 26 or 27 is being issued, this instruction is queued, the datalogger proceeds to the PakBus address of this...
CR10X Measurement and Control System - Page 342
... address of any datalogger used to store the datalogger's routing table information in a series of input locations. Note: The input locations required for this instruction must be allocated manually. The PakBus Address of information returned:
1. Program Control Instructions
Result Location
Result Code -1001 -1002 -1003 0 >1
Description The attempted setting is a read-only setting Out of...
Campbell Scientific CR10X Reviews
We have not received any reviews for Campbell Scientific yet.