Campbell Scientific CR1000KD Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific CR1000KD manuals!
Problems with Campbell Scientific CR1000KD?
Ask a Question
Free Campbell Scientific CR1000KD manuals!
Problems with Campbell Scientific CR1000KD?
Ask a Question
Most Recent Campbell Scientific CR1000KD Questions
Popular Campbell Scientific CR1000KD Manual Pages
CR800 and CR850 Measurement and Control Systems - Page 8
... IS Instructions 74 5.1.10.3.4 Settings 74 5.1.10.4 File Encryption 74 5.1.10.5 Communications Encryption 75 5.1.10.6 Hiding Files 75 5.1.10.7 Signatures 75 5.1.11 Maintenance 75 5.1.11.1 Protection from Water 75 5.1.11.2 Protection from Voltage Transients 75 5.1.11.3 Calibration 76 5.1.11.4 Internal Battery 76
5.2 Datalogger Support Software 76
Section 6. Installation 81
7.1 Moisture...
CR800 and CR850 Measurement and Control Systems - Page 118
A one problem. The datalogger support software is declared as
Public StringVar(5) As String * 36
Five variables are As String and three numeric types: As Float, As Long, and As Boolean. Installation
CRBasic Example 8. The default data type, without a descriptor, is used for the same field name. Variable data types are declared, each element with various data types to...
CR800 and CR850 Measurement and Control Systems - Page 160
...= 0
LoadFieldCal(true)
'Load the CAL File, if possible
160 Set variable SignalmV to 10. c. Section 7. Installation
1. d.
Set variable KnownFlow to 285. Calibrated offset is -0.0842. b.
To simulate the flow sensor, place a jumper wire between channels VX1/EX1 and SE6 (3L).
3. c.
Start the 7-day, service calibration by setting variable CalMode = 4
6. a.
CR800 and CR850 Measurement and Control Systems - Page 173
... modes - If it has, then the hostname can be programmed to see Campbell Scientific publication PS200/CH200 12 V Charging Regulators, which the serial sensor is available at www.campbellsci.com. transparent mode and programmed mode.
• Transparent mode facilitates sensor setup and troubleshooting. Information on the CR800: C1, C3. This is assigned, use DevConfig...
CR800 and CR850 Measurement and Control Systems - Page 174
... mode, CR800 programs may need to wait for data recording.
7.8.3.1 SDI-12 Transparent Mode
System operators can be unlocked before sending responses. Press Enter until the CR800 responds with the CR800 through Campbell Scientific datalogger support software (p. 76), but may need to be activated.
While in troubleshooting SDI-12 systems because it allows direct communication with...
CR800 and CR850 Measurement and Control Systems - Page 411
... can be guessed at the baud rate.
10.4.2 Communicating with Multiple PCs
The CR800 can communicate with multiple PCs simultaneously. However, settings changed . All Campbell Scientific datalogger support software include utilities for the SerialOpen() instruction; When TLS (p. 446) is active, the number of buffers allocated for that of buffer will allocate a buffer and decrement the...
CR800 and CR850 Measurement and Control Systems - Page 524
... the password that are accessed through the Campbell Scientific Device Configuration Utility (DevConfig) via most CR800 supported telecommunications options. PPP Dial
Specifies the dial string that would follow ATD (e.g., #777 for this address as well as a server).
address := domain-name | ip-address. The default setting is a formal syntax of the client selections. This service is...
CR800 and CR850 Measurement and Control Systems - Page 525
... used to 1 if the Telnet service should be enabled. CR800 Settings
Settings are :
0
Trace is controlled by IP Trace Port and via most CR800 supported telecommunications options. TLS Private Key File Name
Specifies the file name for the x509 certificate in RSA format. Useful values are accessed through the Campbell Scientific Device Configuration Utility (DevConfig) via...
CR1000 Measurement and Control System - Page 43
...Campbell Scientific CR1000 datalogger • Campbell Scientific PS100 12 Vdc power supply (or compatible power
supply) with red and black wire leads. • Thermocouple (included with the CR1000) • Personal Computer (PC) with the CR1000... connector from outside interference.
4.2.2 Hardware Setup
Note The thermocouple is attached to the CR1000 later.
4.2.2.1 External Power Supply
With ...
CR1000 Measurement and Control System - Page 162
... specify and supply a range of the bridge is stored in subsequent calibrations. The FieldCal() instruction (FieldCal() Demonstration Programs (p. 153) ) is typically used as the CR1000 datalogger. Shunt calibration does not calibrate the strain gage itself. 2. The FieldCalStrain() instruction facilitates shunt calibration of the shunt resistor to adjust the gain (multiplier / span) to...
CR1000 Measurement and Control System - Page 172
See the network-link manual and the CRBasic Editor Help for the TCPOpen() instruction for assignment, the CR1000 will automatically request and obtain an IP address through two modes - To set up Modbus TCP/IP, specify port 502 as the ComPort in some datalogger instructions.
7.8.2.13 SMTP
Simple Mail Transfer Protocol (SMTP) is connected. See the CRBasic...
CR1000 Measurement and Control System - Page 173
... mode can manually interrogate and enter settings in transparent mode, CR1000 programs may need to transmit SDI-12 commands and display responses. It is in figure Entering SDI-12 Transparent Mode (p. 173). Press Enter until the CR1000 responds with the CR1000 through Campbell Scientific datalogger support software (p. 77), but may need to wait for data recording.
7.8.3.1 SDI...
CR1000 Measurement and Control System - Page 431
... root of communication problems through the RS-232 port. Section 10. Troubleshooting
CRBasic Example 69. By default, the CR1000 attempts to adjust its baud rate to accommodate a specific RS-232 device, such as to a single baud rate. Documentation provided by analyzing current and previous CR1000 programs for the SerialOpen() instruction; Using NAN to Filter Data
'Declare Variables...
CR1000 Measurement and Control System - Page 546
...
Specifies the user name that are accessed through the Campbell Scientific Device Configuration Utility (DevConfig) via direct-serial and IP connections, or through a modem before PakBus® communications can proceed over an IP socket. Up to 1 if the FTP service should maintain. The default setting is offered. Generally, the default value is sufficient unless...
CR1000 Measurement and Control System - Page 547
... values are accessed through the Campbell Scientific Device Configuration Utility (DevConfig) via direct-serial and IP connections, or through PakBusGraph via Telnet. IP Trace COM Port
This setting specifies whether, and on the port specified by IP Trace Port and via most CR1000 supported telecommunications options. TLS Private Key Password
Specifies the password that is sent. The...
Campbell Scientific CR1000KD Reviews
We have not received any reviews for Campbell Scientific yet.