Campbell Scientific SC105 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific SC105 manuals!
Problems with Campbell Scientific SC105?
Ask a Question
Free Campbell Scientific SC105 manuals!
Problems with Campbell Scientific SC105?
Ask a Question
Popular Campbell Scientific SC105 Manual Pages
SC105 9-pin to RS232 DCE Interface - Page 1
SC105 CS I/O to RS-232 Interface
Revision: 11/13
Copyright © 2004-2013 Campbell Scientific, Inc.
SC105 9-pin to RS232 DCE Interface - Page 3
... in lieu of all other locations, Campbell will return such products by Campbell, and product specific training, is not liable for any products which shall be free from defects in the corresponding Campbell pricelist or product manual. Campbell is part of Entry) INCOTERM® 2010, prepaid. Warranty
"PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. Products not manufactured, but...
SC105 9-pin to RS232 DCE Interface - Page 4
... number clearly on products that may not be issued. A completed form must fill out a "Statement of the problem, an RMA number will be either emailed to repair@campbellsci.com or faxed to determine which Campbell Scientific company serves your country. After an application engineer determines the nature of Product Cleanliness and Decontamination" form and...
SC105 9-pin to RS232 DCE Interface - Page 5
... to the printed version of Spark Gap Protection 7
Tables
5-1. Installation 5
5. RAD Modem Application 5
5.1 RAD Modem -
Set-up Menu 3
3.1 Set-up Menu 4 Two Way Communication 6 Installation of this document. SC105 CS I/O to specific sections.
1. Use the PDF reader bookmarks tab for links to RS-232 Interface 1 Set-up Menu Selections 4
4. CDMA Modem Application...
SC105 9-pin to RS232 DCE Interface - Page 7
... RS-232 signal levels. • Power for the SC105 is used to interface a Campbell Scientific datalogger to power the RS-232 modem if needed. • Two way (interactive) communication. • Supports most RS-232 baud rates. • Supports all CS I/O port modes. SC105 CS I/O to RS-232 Interface The SC105 (FIGURE 1-1) is supplied from the 5 V supply on...
SC105 9-pin to RS232 DCE Interface - Page 8
...
5
GND Signal Ground
6
In DSR Data Set Ready (No Connection)
7
Out RTS Request to Send - I /O Name Description
In +5 V Regulated 5 Volt supply
GND Ground
Out Ring
Ring signal to RS-232 Interface
2. Specifications
RS-232 9-Pin Male Connector Pin-out:
Pin No. SC105 CS I/O to datalogger
Out RXD SC105 transmits on this line
In ME...
SC105 9-pin to RS232 DCE Interface - Page 9
... modem connection to the PC, typically Campbell Scientific's Device Configuration Utility (DevConfig) is powered by connecting the SC105's RS-232 port to a PC with the message "Set-up Menu
The SC105 has a built-in DevConfig or menu item 4 if using HyperTerminal or Procomm. If left idle, the Set-up Menu will support the following baud rates: 1200...
SC105 9-pin to RS232 DCE Interface - Page 10
... here, as well as the RS-232 Auto Power Down (APD) Mode. The DTR and RTS Mode setting allows control over how these two lines behave.
DTR is being used, SDC address 7, 8, 10, or... it executes the P96 instruction.
2) RS-232 Port Configuration
RS-232 baud rate, data bits, and parity are both driven to RS-232 Interface
SC105 - SC105 CS I /O Port Configuration
An SC105 may be activated either ...
SC105 9-pin to RS232 DCE Interface - Page 11
... the last data is sent out the RS-232.
'Custom mode': This mode is possible. Installation
Connect the SC105 to the RS-232 device and to communicate across several distances.
5 For SDC Address 7, 8,...RAD modem uses a cable made of two pairs of 2 seconds when data coming in a Campbell Scientific enclosure. Data rates up to 9600 bps are transmitted and received at a balanced impedance, ...
SC105 9-pin to RS232 DCE Interface - Page 12
... communicate through the SC105/RAD modem, "Set-up of the line. To decrease the chances for damage, spark gaps should be purchased from Campbell Scientific (pn 5563 shown in the Connect window.
5.2 RAD Modem Wiring and Grounding
FIGURE 5-2 shows a typical set the DCE/DTE switch to DCE. Start two way communication using Campbell Scientific's datalogger support software to...
SC105 9-pin to RS232 DCE Interface - Page 13
...power supply that pin to pin continuity exists between the two modems. If the modems are installed entirely within a building, the transient spark gap protection is straight through such that will boost... a customer needs to RS-232 Interface enclosures models ENC10/12, ENC12/14, or ENC16/18). FIGURE 5-2. Spark gap wiring is probably not needed. SC105 CS I/O to transmit data across longer or ...
SC105 9-pin to RS232 DCE Interface - Page 14
..., use a CR10KD Keyboard Display to RCV + and jumper the XMT - When unable to be repaired or replaced.
8 If the datalogger passes tests 4, 5, and 7, but fails test 6, then the SC105 is set up, testing can proceed as HyperTerminalTM or Campbell Scientific's datalogger support software (Test Terminal Emulator) must be within a tenth of the computer. Repeat step 1 by jumpering...
SC105 9-pin to RS232 DCE Interface - Page 15
... radio. This allows communications from the time that can be used , the SC105 DTR and RTS mode setting will be set -up as modem enable 9600 baud, 8 data bits, Parity None and ...9
Standard OS (Array)
X
X
Table Data OS
X
PakBus OS
X
X
7. This sets the SC105 up of the datalogger, the SC105, the Freewave radio, and LoggerNet PC software for the turn-on latency of its low power ...
SC105 9-pin to RS232 DCE Interface - Page 16
SC105 CS I/O to RS-232 Interface 10
Campbell Scientific SC105 Reviews
We have not received any reviews for Campbell Scientific yet.