Campbell Scientific CR510 Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific CR510 manuals!
Problems with Campbell Scientific CR510?
Ask a Question
Free Campbell Scientific CR510 manuals!
Problems with Campbell Scientific CR510?
Ask a Question
Popular Campbell Scientific CR510 Manual Pages
CR510 Basic Datalogger - Page 52
... greater than 4.5 m/s:
3.8 PROGRAM CONTROL LOGICAL CONSTRUCTIONS
Most of the Program Control Instructions have a command code parameter which can be called the subroutine.
3-4 Instruction 89 is placed just before proceeding to another instruction to specifically reset Flag 9 low before Instruction 75 and is used to set Flag 9 high if the wind speed is desired to 4.5 m/s. SECTION...
CR510 Basic Datalogger - Page 59
... it seems the CR510 is currently in Table 1 caused error 23).
Run time errors 9 and 31 are four types of errors flagged by
watchdog timer
09 Run Time Insufficient Input Storage
10 Run Time Low battery voltage
11 Editor
Attempt to the right of times the voltage drops below 9.6 volts.
INSTRUCTION SET BASICS
3.10 ERROR CODES
There are...
CR510 Basic Datalogger - Page 61
... is referred to set the Output Array ID, enter Instruction 80 (Section 11).
3. This instruction must be used to multiple peripherals. A specific pin in the datalogger program for on -line transfer of the CR510's routine operation) or it sends data to in use or if you wish to output data to be MANUALLY INITIATED.
Enter Instruction 96 to enable...
CR510 Basic Datalogger - Page 67
... 6 and in the American Standard Code for the devices. Campbell Scientific has developed a software package which automates data retrieval and facilitates the programming of Campbell Scientific dataloggers and the handling of these links. These commands and the responses to program the CR510. Those details are sent in the individual manuals for Information Interchange (ASCII). The...
CR510 Basic Datalogger - Page 81
...
05: Do (P86) 1: 51
Set Port 1 Low
7.4 ANEMOMETER WITH PHOTOCHOPPER OUTPUT
An anemometer with the cups, allows light to pass from the source to 10 pulses per 60 seconds (1 minute) or 6 rpm = 1 pulse per sec. (Hz). Young Model 12102D Cup Anemometer, with a Configuration Code of the Pulse Count Instruction (Configuration Code = 20) is the R.
Thus...
CR510 Basic Datalogger - Page 162
... at specific points during program execution may be compensated for every 512 times that the program table is compiled that Instruction 24 is executed. To prevent overrun errors which makes a temperature measurement, and sets flag 1 if the temperature exceeds a fixed value. Instruction 24 calibration ensures that the coefficients are replaced each time that contains Instruction 24...
CR510 Basic Datalogger - Page 174
... PE line) in the ∗6 Mode. PRINT DEVICE: Any device capable of data generated by Output Processing Instructions is set . A low resolution data value requires 1 Final Storage location (2 bytes). OUTPUT ARRAY: A string of data to raise the CR510's ring line or be used with the CR510.
The data points which complete the Array are the result of the...
CR510 Basic Datalogger - Page 193
...'s modbus driver does not support floating point, and thus is set . APPENDIX F. CR10(X) users have "coils" originally meaning coil relays that support Modbus. The register is available as spread spectrum radios may require an SC932.
MODBUS ON THE CR10(X) AND CR510
Modbus communication capability is followed by PC208 and most SCADA software packages.
Campbell Scientific
Modbus...
CR510 Basic Datalogger - Page 209
... programs for Campbell Scientific CR10X dataloggers. Key
Display
Explanation
*
00:00
Enter mode.
1
01:00
Enter Program Table 1. Next, connect the CR10X to store the measurement, location 1. AD-OV-3
The program can be slightly different. Entering an instruction into the CR10X in one of
ROM), in Section OV5, or on the keyboard/display. NetAdmin supports communication via...
CR510 Basic Datalogger - Page 246
...: The CR10X-TD and CR510-TD have limited communication rates and do not support options 4 through the loop. When a PakBus command is received from the remote.
When this address refers to automatically increment the address with each pass through 7. The PakBus and Modbus addresses in the datalogger cannot be set a value in parameter 3), Instruction 63...
CR510 Basic Datalogger - Page 256
... of values sent is not set in which holds the first value that will be left at 0.
Enter the level 2 security code for the transferred data must be stored. Subsequent data values from the host (master) datalogger should be received from the host (master) datalogger when data is transferred. Program Control Instructions
Swath to Send parameter...
CR510 Basic Datalogger - Page 258
...locations required for this instruction must be allocated manually. Program Control Instructions
Result Location
Result Code -1001 -1002 -1003 0 >1
Description The attempted setting is a read-only setting Out of space in the remote Syntax error Success Number of communication failures
Routing Table Information (P199)
A program control instruction that is used as a trouble-shooting tool.
10...
TD Operating System Addendum for CR510, CR10X, and CR23X - Page 11
Entering an instruction into a program table is a prompting editor for writing and documenting programs for Campbell Scientific CR10X dataloggers.
Program files developed with a simple programming example.
A
02:P00
Enter the location # and advance to the CR10X using EDLOG. Sections 9-12 have more detailed descriptions of the parameters. EDLOG is described in OV5. OV5. ...
TD Operating System Addendum for CR510, CR10X, and CR23X - Page 48
..., 4800 Modem Enabled Device, 19200 Modem Enabled Device, 38400 SDC 6 (COM 310) SDC 7 SDC 8
Note: The CR10X-TD and CR510-TD have limited communication rates and do not support options 4 through the loop.
Program Control Instructions
Port Address
Notes:
Edlog allocates only one of this instruction.
Valid options are handled later when the remote replies.
TD Operating System Addendum for CR510, CR10X, and CR23X - Page 60
... a read-only setting Out of space in the remote Syntax error Success Number of input locations. For each hop takes 1 second). A -1 in a series of communication failures
Routing Table Information (P199)
A program control instruction that is used as a trouble-shooting tool.
10: PakBus - Note: The input locations required for this instruction must be allocated manually. Section 12...
Campbell Scientific CR510 Reviews
We have not received any reviews for Campbell Scientific yet.