Fluke 9100S-A-156 Support and Manuals
Get Help and Manuals for this Fluke item
View All Support Options Below
Free Fluke 9100S-A-156 manuals!
Problems with Fluke 9100S-A-156?
Ask a Question
Free Fluke 9100S-A-156 manuals!
Problems with Fluke 9100S-A-156?
Ask a Question
Popular Fluke 9100S-A-156 Manual Pages
Manual - Page 2
... service center within the warranty period. Fluke does not warrant calibrations on the date of the shipment. Fluke reserves the right to invoice Buyer for Fluke products online at Fluke's option, to change without interruption. The warranty period begins on the Field Metrology Well. Specifications subject to refund of the purchase price, free of charge repair, or replacement of Fluke...
Manual - Page 4
9100S Dry-Well Calibrator
6.3.1 Scan Control 22 6.3.2 Scan Rate...22 6.4 Set-point Resistance 22 6.5 Secondary Menu 23 6.6 Heater ... Commands 32
8 Test Probe Calibration 35
8.1 Calibrating a Single Probe 35 8.2 Dry-well Characteristics 35
8.2.1 Stabilization and Accuracy 35
9 Calibration Procedure 37
9.1 Calibration Points 37 9.2 Calibration Procedure 37
9.2.1 Compute DELTA ...
Manual - Page 9
... (Alternating Current)
1
MyFlukeStore Shop for portability, low cost, and ease of temperature sensors and devices. 1 Before You Start
Before You Start
Symbols Used
1.1 Introduction
The Fluke 9100S Mid-Range Field Calibrator may be used on the instrument or in this manual.
Manual - Page 10
... Impulsive Withstand Voltage protection provided.
9100S Dry-Well Calibrator
Symbols Used
Symbol Description
AC-DC
Battery
Complies with European Union directives
DC
Double Insulated
Electric Shock
Fuse
PE Ground
Hot Surface (Burn Hazard)
Read the User's Guide (Important Information)
Off
On
Canadian Standards Association
CAT II OVERVOLTAGE (Installation) CATEGORY II, Ploution Degree...
Manual - Page 12
...dry-wells designed for Fluke products online at temperatures ...installed correctly.
●● Always replace the power cord with one of the same rating, voltage and type.
1.3.2 Cautions
●● Always operate this instrument without a properly grounded, properly polarized power cord. 9100S Dry-Well Calibrator... areas close to the outlet is set -point less than 50°C. This...
Manual - Page 13
....
●● The Factory Reset Sequence (see Section 11, Troubleshooting, on your Fluke product:
5
MyFlukeStore Shop for optimum durability and trouble free operation, it are sensitive instruments that the probe handle temperature limit is important to the safety and proper operation of the calibrator.
●● DO NOT drop the probe sheath in correcting...
Manual - Page 14
9100S Dry-Well Calibrator
Authorized Service Centers
6
MyFlukeStore Shop for Fluke products online at: www.
.com 1.877.766.5412
Manual - Page 15
Before You Start
Authorized Service Centers
E-mail: antng@singa.fluke.com When contacting these Service Centers for support, please have the following information available:
●● Model Number ●● Serial Number ●● Voltage ●● Complete description of the problem
7
MyFlukeStore Shop for Fluke products online at: www.
.com 1.877.766.5412
Manual - Page 17
...
250 V 3 A FF (very fast acting) NO USER SERVICEABLE PARTS
2.2 Environmental Conditions
Although the instrument has been designed for Fluke products online at equal depths within ±10% of nominal ●● vibrations in the calibration environment should not be operated in the Maintenance Section of this manual. The instrument should be minimized ●● altitudes...
Manual - Page 19
... that the nominal voltage corresponds to Section 3.1, Specifications, for safe and easy insertion and removal of the proper voltage, frequency, and current capability. 3 Quick Start
Quick Start
Setting the Temperature
3.1 Unpacking
Unpack the dry-well carefully and inspect it Software and User's Guide
3.2 Set-up
Place the calibrator on a flat surface with at : www.
.com...
Manual - Page 40
...Fluke products online at: www.
.com 1.877.766.5412 The interface makes no distinction between upper and lower case letters, hence either set a parameter or display a parameter depending on
Read scan rate
sr[ate]
sr
Set scan rate
sr[ate]=n
sr=1.1
Returned
set...or printer or to erase the previous character.
9100S Dry-Well Calibrator
Interface Commands
The serial port can be sent...
Manual - Page 41
... to user
x Character data returned to user
Note: When DUPLEX is set to FULL and a command is sent to 0.006
Set DELTA calibration parameter de[lta]=n
de=1.37
de: 9.99999
0-3.0
Miscellaneous Other Commands
Read firmware version number *ver[sion]
*ver
ver.9999x,9.99 ver.9100S,1.01
Read structure of all commands h[elp]
h
list of commands...
Manual - Page 46
9100S Dry-Well Calibrator
Calibration Procedure
9.2.1 Compute DELTA A = T3 − T2 B = T2 − T1
... temperature and set-point resistance at 50.0 °C T2 and R2 are the measured temperature and set-point resistance at 200.0 °C T3 and R3 are the measured temperature and set-point resistance ...Section )
38
MyFlukeStore Shop for Fluke products online at: www.
.com 1.877.766.5412
Manual - Page 51
... The scan and scan rate settings may have the instrument's model number, serial number, voltage, and problem description available. Improper line voltage. Proportional band may help to be responding too quickly). a NVRAM error Err 3 - an ADC ready error Err 6 - Troubleshooting
Troubleshooting Problems, Possible Causes, and Solutions
11 Troubleshooting
This section contains information on...
Datasheet - Page 4
... is easy with a handheld dry-well.
754 DOCUMENTING PROCESS CALIBRATOR
2514 dry-well interface cable
Null modem
Fluke Calibration Dry-well (DB9)
Ordering information
9100S Handheld Dry-Well 8 9300 Rugged Carrying Case, 9100
9102S Handheld Dry-Well, comes with your choice of temperature sensors • 9100S model weighs only 2 lbs, 3 oz (1 kilogram) • Temperature ranges from -10...
Fluke 9100S-A-156 Reviews
We have not received any reviews for Fluke yet.