Fluke 9103-A-156 Support and Manuals
Get Help and Manuals for this Fluke item
View All Support Options Below
Free Fluke 9103-A-156 manuals!
Problems with Fluke 9103-A-156?
Ask a Question
Free Fluke 9103-A-156 manuals!
Problems with Fluke 9103-A-156?
Ask a Question
Popular Fluke 9103-A-156 Manual Pages
Product Manual - Page 3
... Cautions 3
1.3 Authorized Service Centers 3
2 Introduction 7
3 Specifications and Environmental Conditions 9
3.1 Specifications 9 3.2 Environmental Conditions 9 3.3 Warranty 10
4 Quick Start 11
4.1 Unpacking 11 4.2 Setup 11 4.3 Power 11 4.4 Setting the Temperature 12
5 Parts and Controls 13
5.1 Back Panel 13 5.2 Front Panel 13 5.3 Constant Temperature Block Assembly 15 5.4 Probe...
Product Manual - Page 10
...
To avoid personal injury, follow these guidelines. DO NOT connect this unit without a properly grounded, properly polarized power cord. BURN HAZARD - 9103 Dry-Well User's Guide
Symbol
Description Canadian Standards Association
OVERVOLTAGE (Installation) CATEGORY II, Pollution Degree 2 per IEC1010-1 refers to a non-grounded, non-polarized outlet. DO NOT remove inserts at : www.
.com...
Product Manual - Page 13
1 Before You Start Authorized Service Centers
When contacting these Service Centers for support, please have the following information available:
• Model Number • Serial Number • Voltage • Complete description of the problem
5
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664
Product Manual - Page 15
... continuously shows the current well temperature. The temperature may be familiar with pulsed driven Thermal Electric Devices (TED). The 9103 Dry-well was designed for Fluke products online at: www.
.com 1.888.610.7664 The calibrator features:
• Convenient handle • RS-232 interface • Universal AC input
Built in this user manual.
7
MyFlukeStore Shop for portability...
Product Manual - Page 17
...temperature range: 5-45°C (41-113°F) • ambient relative humidity: 15 - 50% • pressure: 75kPa - 106kPa • mains voltage within ± 10% of this manual. 3
3.1
3.2
3 Specifications and Environmental Conditions Specifications
Specifications and Environmental Conditions
Specifications... calibration ...it Software (Model 9930) 10.25" H x 5.63"... Fluke ...
Product Manual - Page 19
... • Manual
4.2
Setup
Place the calibrator on a flat surface with at : www.
.com 1.888.610.7664 Refer to operate please check the power connection. Observe that the nominal voltage corresponds to that the following components are present:
• 9103 Dry-well • Insert for power details. Turn on and begin to show the well temperature and...
Product Manual - Page 20
9103 Dry-Well User's Guide
4.4
Setting the Temperature
Section 7.2 explains in the new set-point.
(4) Press "EXIT" to return to the temperature display. The displayed well temperature gradually changes until it reaches the set -point on or off to raise or lower the temperature. Another 6 to 10 minutes is required to 30 minutes more of the set -point depending on the span...
Product Manual - Page 23
... Controls Constant Temperature Block Assembly
99110 3 DRY-WELL CALIBRATTOORR -25°C to fit snugly into the calibrator well and tongs for sensors of that is to the displayed value are available allowing the user's probe to 140°C
104.6 C Smoked Display Window
SWITCH HOLD
SET
DOWN
UP
EXIT
Figure 2 9103 Front Panel
EXIT - The calibrator is inserted...
Product Manual - Page 24
9103 Dry-Well User's Guide
• Insert A (variety block): 1/2", 3/8", 1/4", 3/16", 1/8", and 1/16" holes • Insert B (comparison block): 2 each 3/8", 2 each 1/4", and 2 each 3/16"
holes • Insert C (1/4" comparison block): 6...4 mm
6 mm 4 mm
6 mm 3 mm
Figure 3 Inserts Available for the 9103 Block Assembly
16
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664
Product Manual - Page 28
... Period
Duplex Mode
Adj. SEE MANUAL
EXIT
Cal Menu
SET X5
R0
Adj. DELTA
BETA Adjust BETA
20
MyFlukeStore Shop for Fluke products online at: www.
.... menu and display the temperature
Figure 4 Controller Operation Flowchart
EXIT
Serial Interface
Menu
SET
BAUD Rate
Adjust BAUD Rate
Sample Period
Adj. SEE MANUAL
9103 Dry-Well User's Guide
Display Temperature
SET Select Setpoint
Adjust Setpoint
...
Product Manual - Page 40
... be changed using "UP" or "DOWN" and pressing "SET".
32
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664 To enter the serial parameter programming mode first press "EXIT" while pressing "SET" and release to the next parameter in seconds between temperature measurements transmitted from the serial interface. Press "UP" until...
Product Manual - Page 42
9103 Dry-Well User's Guide
Table 2 9103 Controller Communications Commands
Command Description Display Temperature Read current set-point Set current set-point to n
Command Format
s[etpoint] s[etpoint]=n
Command Example
s s=200.0
Read temperature Read temperature units Set temperature units: Set temperature units to Celsius Set temperature units to Fahrenheit Read scan mode Set scan mode Read...
Product Manual - Page 48
R1-4 - 9103 Dry-Well User's Guide
10.2.2
B = T3 − T2
C
=
⎡ T4 ⎣⎢100
...temperature using thermometer. Value of R from display of 9103 (Press SET and DOWN at the same time.) where T1 and R1 are the measured temperature and resistance at -25°C T2 and R2 are the measured temperature...
40
MyFlukeStore Shop for Fluke products online at: www.
.com 1.888.610.7664
Product Manual - Page 53
... model number, and the firmware version. Check the Scan and Scan Rate settings.
an ADC setup error Err 5 - Incorrect R0, ALPHA, DELTA, and BETA parameters. Find the value for assistance. The displayed temperature is frozen keeping the
at the left of your instrument available. Be sure to have locked up .
a NVRAM error Err 3 - 12
12.1
12 Trouble Shooting Troubleshooting...
Product Manual - Page 54
... as described above . If the unit repeats the error code, turn the unit off the unit and contact contact a Hart Scientific Authorized Service Center for a return authorization and for instructions on . If no change ocout is not the actual curs, the unit may be calibrated. 9103 Dry-Well User's Guide
Problem
Possible Causes and Solutions
The display shows Defective...
Fluke 9103-A-156 Reviews
We have not received any reviews for Fluke yet.