Installation Instructions
Page 1
... www.garmin.com/support/. WARNING: See the Important Safety and Product Information guide in Taiwan The serial number is located on the model. In Europe, contact Garmin (Europe) Ltd. screw (1) F - 1/4 in . (4) J - rubber washer (1) Tools Needed • Drill and drill bits I K G - NMEA 2000 T-connector (1) (NMEA 2000 Intelliducer only) • Number 2 Phillips screwdriver • Marine sealant March 2008 190-00889-01 Rev. Cable tie, 5.6 in . This Transom Mount Intelliducer provides depth information either to a NMEA...
... www.garmin.com/support/. WARNING: See the Important Safety and Product Information guide in Taiwan The serial number is located on the model. In Europe, contact Garmin (Europe) Ltd. screw (1) F - 1/4 in . (4) J - rubber washer (1) Tools Needed • Drill and drill bits I K G - NMEA 2000 T-connector (1) (NMEA 2000 Intelliducer only) • Number 2 Phillips screwdriver • Marine sealant March 2008 190-00889-01 Rev. Cable tie, 5.6 in . This Transom Mount Intelliducer provides depth information either to a NMEA...
Installation Instructions
Page 2
... into the Intelliducer mount. 3. Route the NMEA 2000 or power/data cable toward the back of the Intelliducer 2. Place the 5 mm flat washer on single-drive boats. screw. Step 2: Mount the Intelliducer When selecting a transom-mount location, consider the following for optimal performance: • For your sonar to operate properly, the Intelliducer must be in calm water. • Mount the Intelliducer as possible. • DO NOT mount the Intelliducer in locations where it...
... into the Intelliducer mount. 3. Route the NMEA 2000 or power/data cable toward the back of the Intelliducer 2. Place the 5 mm flat washer on single-drive boats. screw. Step 2: Mount the Intelliducer When selecting a transom-mount location, consider the following for optimal performance: • For your sonar to operate properly, the Intelliducer must be in calm water. • Mount the Intelliducer as possible. • DO NOT mount the Intelliducer in locations where it...
Installation Instructions
Page 3
... a fiberglass hull or 3/8 in the path of the transom. 6. Mount the Intelliducer parallel with marine sealant before installation. Do not mount the Intelliducer directly in . (9.5 mm) below water level when the boat is on plane at the marked locations. Apply marine sealant to the backbone of your existing NMEA 2000 network. Drill a 1/8 in. (3.2 mm) pilot hole approximately 3/8 in . (25 mm) deep at high speed. Tighten the...
... a fiberglass hull or 3/8 in the path of the transom. 6. Mount the Intelliducer parallel with marine sealant before installation. Do not mount the Intelliducer directly in . (9.5 mm) below water level when the boat is on plane at the marked locations. Apply marine sealant to the backbone of your existing NMEA 2000 network. Drill a 1/8 in. (3.2 mm) pilot hole approximately 3/8 in . (25 mm) deep at high speed. Tighten the...
Installation Instructions
Page 4
...-in drop cable on NMEA 2000, visit www.garmin.com. Route the built-in ) Additional NMEA 2000 device (not included) Transom mount Intelliducer Connecting the Intelliducer to your existing NMEA 2000 network: 1. For more information on the Intelliducer to the bottom of a NMEA 2000 T-connector, or disconnect a terminator from the backbone nearest to the location where you added to a NMEA 2000 Network Transom Mount Intelliducer Installation Instructions To connect the Transom Mount Intelliducer to a NMEA 2000 Network The Intelliducer is packaged with a NMEA 2000 T-connector.
...-in drop cable on NMEA 2000, visit www.garmin.com. Route the built-in ) Additional NMEA 2000 device (not included) Transom mount Intelliducer Connecting the Intelliducer to your existing NMEA 2000 network: 1. For more information on the Intelliducer to the bottom of a NMEA 2000 T-connector, or disconnect a terminator from the backbone nearest to the location where you added to a NMEA 2000 Network Transom Mount Intelliducer Installation Instructions To connect the Transom Mount Intelliducer to a NMEA 2000 Network The Intelliducer is packaged with a NMEA 2000 T-connector.
Installation Instructions
Page 5
... the boat battery if it to the gray wire (Tx A) from the Intelliducer, and leave the white/red wire (Tx B) from the Intelliducer should be connected to correctly wire the Intelliducer. On Tx A(+) Tx B(-) Spare Spare > > Transom Mount NMEA 0183 Intelliducer Power/Data Cable NMEA 0183 Intelliducer +Battery- If you are wiring the Intelliducer to ground. caution: If you are wiring the Intelliducer to the ignition or install an in-line switch. Step 3 (NMEA 0183...
... the boat battery if it to the gray wire (Tx A) from the Intelliducer, and leave the white/red wire (Tx B) from the Intelliducer should be connected to correctly wire the Intelliducer. On Tx A(+) Tx B(-) Spare Spare > > Transom Mount NMEA 0183 Intelliducer Power/Data Cable NMEA 0183 Intelliducer +Battery- If you are wiring the Intelliducer to ground. caution: If you are wiring the Intelliducer to the ignition or install an in-line switch. Step 3 (NMEA 0183...
Installation Instructions
Page 6
... following PGN information across your NMEA 2000 network: 059392 060928 126208 126464 126996 128267 130312 ISO Acknowledgement ISO Address Claim NMEA-Command/Request/Acknowledge Group Function Transmit/Receive PGN List Group Function Product Information Water Depth Temperature Garmin Intelliducers are using the Intelliducer with an existing Garmin chartplotter, upgrade your Garmin chartplotter with the latest software to ensure compatibility with NMEA 0183 devices using the SDDPT, SDDBT, and SDMTW NMEA 0183 sentences. Transom Mount Intelliducer Installation Instructions Step 4�...
... following PGN information across your NMEA 2000 network: 059392 060928 126208 126464 126996 128267 130312 ISO Acknowledgement ISO Address Claim NMEA-Command/Request/Acknowledge Group Function Transmit/Receive PGN List Group Function Product Information Water Depth Temperature Garmin Intelliducers are using the Intelliducer with an existing Garmin chartplotter, upgrade your Garmin chartplotter with the latest software to ensure compatibility with NMEA 0183 devices using the SDDPT, SDDBT, and SDMTW NMEA 0183 sentences. Transom Mount Intelliducer Installation Instructions Step 4�...
Installation Instructions
Page 7
... code of the Software are valuable trade secrets of Garmin and that the Software is the property of Garmin and is in Garmin. You agree not to decompile, disassemble, modify, reverse assemble, reverse engineer, or reduce to the Software remain in compliance with the essential requirements and other relevant provisions of Conformity link. PLEASE READ THIS AGREEMENT CAREFULLY. Transom Mount Intelliducer Installation Instructions...
... code of the Software are valuable trade secrets of Garmin and that the Software is the property of Garmin and is in Garmin. You agree not to decompile, disassemble, modify, reverse assemble, reverse engineer, or reduce to the Software remain in compliance with the essential requirements and other relevant provisions of Conformity link. PLEASE READ THIS AGREEMENT CAREFULLY. Transom Mount Intelliducer Installation Instructions...
Installation Instructions
Page 8
... to download a single copy of Garmin. © Copyright 2008 Garmin Ltd. Except as expressly provided herein, no part of this manual may not be reproduced, copied, transmitted, disseminated, downloaded or stored in the USA and other countries. Information in the content without the express permission of this document is a trademark of Garmin Ltd. Garmin hereby grants permission to make changes in this manual...
... to download a single copy of Garmin. © Copyright 2008 Garmin Ltd. Except as expressly provided herein, no part of this manual may not be reproduced, copied, transmitted, disseminated, downloaded or stored in the USA and other countries. Information in the content without the express permission of this document is a trademark of Garmin Ltd. Garmin hereby grants permission to make changes in this manual...