Harbor Freight Tools 61482 - 1/4 in. Air Hydraulic Riveter Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 61482 manuals!
Problems with Harbor Freight Tools 61482?
Ask a Question
Free Harbor Freight Tools 61482 manuals!
Problems with Harbor Freight Tools 61482?
Ask a Question
Popular Harbor Freight Tools 61482 Manual Pages
User Manual - Page 2
... not avoided, will result in the loss of control of Contents
Safetye 2 Specifications 6 Setup 7 Operationa 10
Maintenancei 12 Parts List and Diagram 14 Warranty 16
Safety
Setup
Operation
WARNING SYMBOLS AND DEFINITIONS This is the safety alert symbol.
Obey all the instructions before using tools, basic precautions should always be followed, including the following:
General...
User Manual - Page 3
... service must be controlled with the specific tool model, increases the risk of binding and is off . Use only the lubricants supplied with your finger on or off before leaving the work by the manufacturer for misalignment or binding of moving parts. Dress properly.
Use clamps or another practical way to secure and support the...
User Manual - Page 4
... to persons. Wear ANSI‑approved eye protection.
Setup
Operation
Maintenance
Page 4
For technical questions, please call 1-800-444-3353.
Never use oxygen, carbon dioxide, combustible gases or any bottled gas as marked on the tool.
Item 61482
SAVE THESE INSTRUCTIONS. Symbols and Specific Safety Instructions
Symbol Definitions
Symbol
Property or statement
PSI Pounds...
User Manual - Page 5
... ensure medical problems are : ...manual for an extended period should first be examined by a doctor and then have impaired blood circulation to cause birth defects (or other reproductive harm. Moving parts... & Safety Code § 25249...manual. Anyone using vibrating tools regularly or for the air compressor used Rivet Pins.
2.
Install... Safety
Setup
Specific Safety Instructions
1. If...
User Manual - Page 6
Item 61482 Safety
Functional Description
Specifications
Maximum Air Pressure Air Inlet Average Air Consumption Rivet Pin Capacity
Components and Controls
90 PSI
1/4″ -18 NPT
4.5 CFM @ 90 PSI 1/8", 5/32", 3/16", 1/4" (Nosepiece change needed)
Pin Cap Pin Cap Nut
Nosepiece Outer Cylinder
Trigger
Setup
Operation
Maintenance
Page 6
Air Inlet For technical questions, please call...
User Manual - Page 7
... parts ...service, as a coupler plug and quick coupler, will make operation more drops after disconnecting to Operation section for this tool.
1. Safety
Setup
Initial Tool Set Up/Assembly
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual...manual. The shutoff valve should not be present after the air supply is disconnected from the air supply. Repair...
User Manual - Page 8
... tool lubrication Provides quick connection and release Increases coupler life Prevents water vapor from damaging workpiece For fine tuning airflow at tool
Item 61482
Safety
Setup
Operation
Maintenance
Page 8
Figure A: Portable Air Supply Setup
Lubricated Tools
BC D
A
E
F
A
For technical questions, please call 1-800-444-3353.
User Manual - Page 9
Figure B: Stationary Air Supply Setup
Item 61482
Slope
Lubricated
G
Tools
C
J
K
H
L
M
F
CD E
For technical questions, please call 1-800-444-3353. I
IN
B A
B A
F
C
J
F
Non-lubricated Tools
LO H
Description
A Vibration ... release Increases coupler life Prevents water vapor from damaging workpiece For fine tuning airflow at tool
Page 9
Maintenance
Operation
Setup
Safety
User Manual - Page 10
...
Maintenance Safety
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use , looking for damaged, loose, and missing parts. Improper adjustment can result in place before performing any problems are stored in a way not specifically explained within this manual. Page 10...
User Manual - Page 11
...must be long enough to the needed pressure. General Operating Instructions
1. CAUTION! Then, release pressure on the air compressor, and set its regulator to reach the work area must not be required... to possible damage. Then store the tool indoors out of the Riveter.
5. Safety
Setup
Workpiece and Work Area Set Up
1. Secure the Pin Cap (9) firmly to the Riveter by children or pets ...
User Manual - Page 12
...Setup
User‑Maintenance Instructions
Procedures not specifically explained in liquids.
Quarterly (every 3 months) - Use care as part of the regular operation of Jaws into the Jaw Case.
5. To replace the Jaws, insert the new set of the air-operated tool.
1. If abnormal noise, vibration, or leaking air occurs, have the problem...the tool in this manual must be highly flammable, causing...
User Manual - Page 13
... Jaws.
1. Tighten Nosepiece. 2. Have compressor serviced by a qualified technician/
upgrade to Figure D.
9. Poor hose connections. 2. see page 10. 3. Follow all safety precautions whenever diagnosing or servicing the tool.
Jaw Case (3)
Jaw Cylinder
(13)
Lock Nut (14)
Housing (15)
Figure D: Checking Jaw Case Tightness
Troubleshooting
Problem
Jaws slipping. Weak pulling action...
User Manual - Page 14
... MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Page 14
For technical questions...
User Manual - Page 15
Page 15
Assembly Diagram
Safety
Setup
Operation
Maintenance
Item 61482
For technical questions, please call 1-800-444-3353.
User Manual - Page 16
...part must bear the cost of our product. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation...800) 444-3353 This warranty gives you specific legal rights and you with transportation charges... We will either repair or replace the product at our...
Harbor Freight Tools 61482 Reviews
We have not received any reviews for Harbor Freight Tools yet.