Harbor Freight Tools 63086 - 8750 Peak/7000 Running Watts Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 63086 manuals!
Problems with Harbor Freight Tools 63086?
Ask a Question
Free Harbor Freight Tools 63086 manuals!
Problems with Harbor Freight Tools 63086?
Ask a Question
Popular Harbor Freight Tools 63086 Manual Pages
User Manual - Page 1
....com Email our Engine support at: [email protected]
When unpacking, make sure that the product is intact and undamaged. Write the product's serial number in a safe and dry place for assembly and service may not be included. All rights reserved. Due to do so can result in any parts are open. EGnegnineeraetxohrauesxthcaounstatincsocnatrabionns...
User Manual - Page 2
...Setup 6 Specifications 6 Operation 10
Maintenance 16 Parts List and Diagram 22 Warranty 24
Safety
Setup
Operation
WARNING SYMBOLS AND DEFINITIONS This is restricted to only qualified service personnel who have been instructed...all applicable laws and electrical codes. Operation of security and shall be installed by a qualified electrician. Set up Precautions
1.
Connections for...
User Manual - Page 3
...codes and standards before grounding. Always read and adhere to the instruction manual ... parts of the Generator and interconnecting cables or conductors with any part... The carbon monoxide from the Engine during set up Precautions (continued)
8. Maintenance
ITEM ... which will shorten the service life of the tools ...Setup
Operation
1. Do not fill gas tank while engine is operating.
6.
User Manual - Page 4
...Setup...
38. If damaged, have the Generator serviced before each use .
26.
Guard against... Code § 25249.5, et seq.)
40. Do not operate the Generator with these instructions and in moving parts,...parts. Disconnect all connections and disconnected wires.
19. If above 85 dBA is repaired or replaced... model. When spills of parts, and any local, state, or federal codes and...
User Manual - Page 5
...Servicing of the receptacles become necessary, use the following precautions are worn, discolored, or corroded. SAVE THESE INSTRUCTIONS.
Should replacement of batteries are uncertain about your model...replacement.
8. c.
Safety
Setup
Service Precautions
1. Unplug all devices from the spark plug.
2. Replace...qualified repair person using only identical replacement parts....
User Manual - Page 6
... pages of this Generator's Engine is warranted for this manual.
Safety
Setup
Functional Description
Specifications
Generator
Output
Battery needed for electric start (not included)...- 0.008" 12 hr. 76 dB Wheel kit (sold separately)
The emission control system for standards set by the U.S. Components and Controls
Fuel Valve Choke
Air Filter Frame
Fuel Cap
DC Receptacle DC Circuit ...
User Manual - Page 8
... and any other parts that control the fuelair ratio will not protect from the engine to operate the electric start fires around dry vegetation. This Generator requires installation of this equipment ... addition of this manual including all text under subheadings therein before use. Note: Wheel Kit, #68531 (sold separately) can be required. Safety
Setup
Initial Tool Set Up/Assembly
Read...
User Manual - Page 10
...repaired. To prevent FIRE, do not start the engine while the smell of the Dipstick and the area around it in a metal fuel container or a dirty fuel container. Safety
Setup
Operating Instructions... Service section shows other viscosities to about 1 inch under subheadings therein before set up to enter the carburetor, effecting engine performance and/or causing damage.
4. Then replace ...
User Manual - Page 11
...with no load for specific instructions
1. Press Test ... the Generator.
IMPORTANT: After starting the engine, allow it is repaired or replaced.
Unplug all electrical loads. c. Inspect the Generator and engine. ...b. Safety
Setup
Using the Generator
Before Starting the Generator Engine
Before starting with no load after each use .
4. Follow the Set Up Instructions
to the ...
User Manual - Page 16
... are in addition to the regular checks and maintenance explained as part of the regular operation of the Generator to cool, and disconnect...Setup
User‑Maintenance Instructions
Procedures not specifically explained in this manual, will differ depending on factors such as a general guide. ITEM 63086 Follow all service instructions in this manual. of equipment will need to be serviced...
User Manual - Page 19
...repair ignition system. plug hole. If that does not remedy problem, replace head gasket.
4. Follow all safety precautions whenever diagnosing or servicing the equipment or engine. Safety
Setup
Troubleshooting
Problem
Engine will occur when trying to start.)
replace...set Choke to air out the chamber. Clean spark plug.
3. Spark plug cap broken.
4. Cylinder not lubricated. If problem ...
User Manual - Page 20
...service.
4. Problem with fresh 87+ octane stabilizer treated unleaded gasoline. Immediately unplug appliance. Follow all safety precautions whenever diagnosing or servicing the equipment or engine. ITEM 63086 Spark plug cap loose.
1. Re-gap or replace spark plug.
3. Replace... capacity exceeded.
2. Safety
Setup
Troubleshooting (continued)
Problem
Engine misfires
Engine stops suddenly...
User Manual - Page 21
... AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY.
NEITHER THE MANUFACTURER OR...
User Manual - Page 22
...
Setup
Parts List and Diagram
Parts List
Part
... Assembly
36 Shaft Assembly, Balancing
37 Ring Set, Oil
38 Clip, Piston Pin
39 Piston... Exhaust Valve Retainer
49 Rotator, Valve
50 Guide, Seal
51 Tappet, Valve
52 Lifter Sub... 1
90 Rod, Governor
1
91 Spring, Governor
1
92 Support Sub, Governor
1
93 Nut
1
94 Bolt, Governor Support
1
95 Collar
1
96 Motor, Starting
1
97 Bolt
2...
User Manual - Page 25
...repair or replace, at our option, any subsequent owner within the two year warranty period. HFT also warrants that you must indicate the specific emissions control part...maintenance services or replacement of this two (2) year warranty. HFT may either (a) contact HFT product support at http://www.harborfreight.com. When going to conform with this warranty under normal use instructions ...
Harbor Freight Tools 63086 Reviews
We have not received any reviews for Harbor Freight Tools yet.