Harbor Freight Tools 63090 - 4000 Peak/3200 Running Watts Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 63090 manuals!
Problems with Harbor Freight Tools 63090?
Ask a Question
Free Harbor Freight Tools 63090 manuals!
Problems with Harbor Freight Tools 63090?
Ask a Question
Popular Harbor Freight Tools 63090 Manual Pages
User Manual - Page 1
...,ay from the product described herein.
Tools required for assembly and service may not be included. windows, doors, and vents.
Diagrams within this manual may not be drawn proportionally. If any parts are open. All rights reserved.
SAVE THIS MANUAL. Owner's Manual & Safety Instructions
Save This Manual Keep this product.
Due to do so can result in...
User Manual - Page 2
... codes. All connections and conduits from utility power, and must be installed so that should contact local fire agencies for the restrictions applied to the location and about any batteries.
IMpORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
This manual contains important instructions that access is to be taken. This unit is restricted to only qualified service personnel...
User Manual - Page 3
...5. Operating precautions
SETUp
OpERATION
1. Do...service life of the Generator.
This is operating.
6. If you cannot see or smell.
9. Do not touch engine during a power outage, and the Generator may be beyond the limit of the product to the instruction manual...set up indoors.
4. Make sure that is in accordance with any part...parts of the all relevant electrical codes...
User Manual - Page 4
...Code § 25249.5, et seq.)
40. If damaged, have the Generator serviced...model. Accessories that may be cleaned up immediately. Stay clear of fuel or oil occur, they must follow OSHA requirements.
23. When spills of hot parts.
33.
Prolonged exposure to the State of transport and lifting devices with these instructions... when it is repaired or replaced. OpERATION
MAINTENANCE
Page...
User Manual - Page 5
... that are uncertain about your model.
4. GFCI protection:
This Generator is sealed by a qualified repair person using only identical replacement parts. Do not smoke, or allow excess to its "OFF" position before moving the Generator and before starting engine. Wipe up any wiring where the insulation is maintained. SAFETY
SETUp
Service precautions
1. Turn the engine switch...
User Manual - Page 6
...last pages of this Generator's Engine is warranted for standards set by the California Air Resources Board (also known as CARB). ITEM 63090 SAFETY
SETUp
Functional Description
Specifications
Generator
Output Electrical Receptacle
Engine
Displacement Engine Type Cooling System
...006" 0.006" - 0.008" 10 hr. 70 dB Wheel kit (sold separately)
The emission control system for this manual.
User Manual - Page 8
... which can start fires around dry vegetation. WARNING! ITEM 63090 SAFETY
Initial Tool Set Up/Assembly
Read the ENTIRE IMpORTANT SAFETY INFORMATION section at least 24 inches deep into... proper spark arrestor installed.
Sensitive electronic equipment includes, but is not intended to the engine and any other parts that has been driven at the beginning of this manual including all text ...
User Manual - Page 10
...parts. If the oil level is hot from ignition sources. It can cause particles to check the oil level. Thread the dipstick back in different average temperatures.)
Note: Do not use . SAFETY
SETUp
Operating Instructions... stored in the Service section shows other viscosities to the full level as shown above.
5. If any problems are found , do not use .
If any problems are found , do...
User Manual - Page 11
....
b. d.
Break-in the SERVICE section. b.
SAFETY
SETUp
Using the Generator
Before Starting the...specific instructions
1. c.
Turn off electricity to the equipment. Then store the unit in products.
5. Basic Generator Use procedure - When finished using the Generator, disconnect all loads from the Generator. Page 11 Note: Do not allow it is repaired or replaced...
User Manual - Page 16
...technical questions, please call 1-888-866-5797. SAFETY
SETUp
User-Maintenance Instructions
procedures not specifically explained in dusty areas. **These items should be serviced by a qualified technician.
Note: The following procedures are in addition to safely service the equipment or engine, have the problem corrected before performing any inspection, maintenance, or cleaning procedures...
User Manual - Page 19
... oil shutdown.
2. Follow all safety precautions whenever diagnosing or servicing the equipment or engine. Replace components damaged by the carburetor needle sticking.
8. Use fresh ...1-888-866-5797. SAFETY
SETUp
Troubleshooting
problem
Engine will not start handle several times to air out the chamber. Have qualified technician diagnose/ repair ignition system. Pour tablespoon ...
User Manual - Page 20
...1. Do not use gasoline with more powerful generator. Plug in again and turn on.
4. Turn off and unplug product. Test GFCI receptacle. Product needs service.
4.
SAFETY
SETUp
Troubleshooting (continued)
problem
Engine stops when under heavy load Engine misfires
Engine stops suddenly
Engine knocks
Engine backfires
Product doesn't have power. Product begins to operating equipment...
User Manual - Page 22
...SETUp
parts List and Diagram
parts List
part...
30 Crankshaft Assembly
31 Ring Set, Oil
32 Clip, Piston ...Guide, Seal
45 Tappet, Valve
46 Lifter, Valve
47 Plate Sub, Lifter Stopper
48 Bolt, Valve Adjusting
49 Rocker, Valve
Qty
1 1 1 1 4 2 2 2 4 1 1 1 1 1 1 2 2 1 1 3 1 2 1 1 1 1 2 1 6 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 2 1 2 2
part...77 Support Sub, Governor
78 Nut
79 Bolt, Governor Support
80...
User Manual - Page 25
...aware that HFT may include parts such as the problem exists in order to obtain warranty repair or replacement, by HFT. Page 25...repairs or replacement should contact HFT product support at no abuse, neglect, or improper maintenance of time, not to follow the fuel use instructions contained in a reasonable amount of your Owner's Manual. If you , including diagnosis, parts and labor. SETUp...
User Manual - Page 26
..., warranty services or repairs will be provided at a retail store.
7. The owner will not be performed at no charge to warrant failures of warranted parts caused by the use of warranty coverage, it will be repaired or replaced HFT. Throughout the emissions warranty period stated above, HFT will be used in the written instructions will maintain...
Harbor Freight Tools 63090 Reviews
We have not received any reviews for Harbor Freight Tools yet.