Harbor Freight Tools 67255 - 14 in. Electric Chain Saw Support and Manuals
Get Help and Manuals for this Harbor Freight Tools item
View All Support Options Below
Free Harbor Freight Tools 67255 manuals!
Problems with Harbor Freight Tools 67255?
Ask a Question
Free Harbor Freight Tools 67255 manuals!
Problems with Harbor Freight Tools 67255?
Ask a Question
Most Recent Harbor Freight Tools 67255 Questions
Putting On The Chain
My chain came off and I am trying to get it back on. I got it on but when I put the bolt on to hold ...
My chain came off and I am trying to get it back on. I got it on but when I put the bolt on to hold ...
(Posted by tadalahr 5 years ago)
Replacement Gear 39
Please instruct how I may order gear 39 for a 67255 - 14 in electric chain saw.
Please instruct how I may order gear 39 for a 67255 - 14 in electric chain saw.
(Posted by rwolfangel 6 years ago)
What Model Depth Gauge Too Do I Use To File Rockers
Harbor freifgt 14" hainsaw needs a raker depth guage tool. What is the product to buy??
Harbor freifgt 14" hainsaw needs a raker depth guage tool. What is the product to buy??
(Posted by Anonymous-162616 6 years ago)
Switch Malfunction On 67255 Chainsaw.
The switch has failed causing the chainsaw to run constantly. The only way to shut it off is to unpl...
The switch has failed causing the chainsaw to run constantly. The only way to shut it off is to unpl...
(Posted by gregbannen 7 years ago)
Popular Harbor Freight Tools 67255 Manual Pages
User Manual - Page 1
... support at: [email protected]
ITEM 67255
When unpacking, make sure that the product is intact and undamaged. Copyright© 2009 by Harbor Freight Tools®. Due to do so can result in a safe and dry place for future reference. SAVE THIS MANUAL. Owner's Manual & Safety Instructions
Save This Manual Keep this manual for assembly and service...
User Manual - Page 4
... when the nose or tip of the guide bar may cause a sudden reverse reaction, kicking the guide bar up in some cases may push the guide bar rapidly back towards the operator.
Tip contact in a tree may catch the saw by a qualified repair person using only identical replacement parts. Pinching the saw chain along the top...
User Manual - Page 5
...saw in this instruction manual cannot cover ...replacement bars and chains specified by the operator that may occur. WARNING: The cord of this grip thumb below : a. Operation
Maintenance
Item 67255
For technical questions, please call 1-888-866-5797. Wash hands after handling. (California Health & Safety Code...Setup
Either of these reactions may cause chain breakage and/or kickback.
User Manual - Page 6
... to carry electricity away from the plug. They have it repaired by a qualified electrician. The plug must be attached to ... with all codes and ordinances. Tools marked with "Grounding Required" have a proper outlet installed by a service facility before ...Three Prong Plugs
3-Prong Plug and Outlet
1. Safety
Setup
Grounding
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING...
User Manual - Page 7
...Setup
Extension Cords
1. Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc. Read the manual...serious injury. Always replace a damaged extension cord or have it repaired by a qualified electrician before set-up the total... Kickback. WARNING marking concerning Risk of Loss of the guide bar tip with side shields. Grounded tools require a ...
User Manual - Page 9
...
Spiked Bumper Chain Guide Bar
Saw Chain Guide Bar Nose
Chain Guide Bar Sheath
Safety Device...manual including all text under subheadings therein before set up or use of the Trigger until manually activated.
3. Operation
Maintenance
Item 67255
For technical questions, please call 1-888-866-5797. Note: For additional information regarding the parts listed in the following pages, refer to Parts...
User Manual - Page 10
...procedure in the middle section under Checking Saw Chain Tension above. Safety
Setup
Guide Bar and Saw Chain Installation and Adjustment
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure ... following sections for checking and adjusting Saw Chain tension and for replacing the Saw Chain when necessary. Item 67255
Chain Guide Bar (71)
Tension Screw (26)
Hex Key Figure C: ...
User Manual - Page 11
... Guide Bar wears evenly over before mounting the new Saw Chain.
Safety
Setup
Replacing the Saw Chain
Do not install a Saw Chain or Chain Guide Bar...Guide Bar. Replace the Drive Cover. Note: For proper placement the tab on the Drive Cover must fit into its hole on the bottom of the Guide Bar. Finger tighten the Nut, then tension the Saw Chain following the steps in the Specifications...
User Manual - Page 12
...before set up or use of this product. The chain saw -horse or cradle before cutting down trees. The escape path should be separated from the tree.
Before felling is clean and well lit.
Safety
Setup
Operating Instructions
... and wire from the bucking operation by a distance of at the beginning of this manual including all text under subheadings therein before cuts are being felled.
User Manual - Page 14
...of limbs, logs or chocks. Item 67255 When possible, the log should be raised and supported by overbucking to meet the first cut.
2nd cut overbuck (2/3 diameter) to meet 1st... avoid cutting earth
Figure H: Log Supported Along the Entire Length When the log is cutting a log into lengths. Cut from the underside (underbuck).
Safety
Setup
Bucking a Log Bucking is supported on both feet.
User Manual - Page 15
...splintering
2nd cut underbuck (2/3 diameter) to meet 1st cut (to avoid pinching) Figure J: Log Supported Both Ends When bucking on a slope always stand on the uphill side of the cut without relaxing...Figure K.
Always stop before moving from the top (overbuck). Safety
Setup
Bucking a Log (continued) When the log is supported on both ends, as illustrated in Figure J, cut , wait for...
User Manual - Page 17
...parts • dull or damaged Saw Chain • any procedure in liquid.
6. If there is a gap, the bar is damaged, it . Maintenance and Servicing
Procedures not specifically explained in this manual must be replaced. BEFORE EACH USE, inspect the general condition of the Guide... Guide Bar
Figure O: Worn Guide Bar
Item 67255
For technical questions, please call 1-888-866-5797. Safety
Setup...
User Manual - Page 19
..., have a qualified technician service the equipment instead.
If Worn or Damaged:
a. Sharpen or replace Saw Chain. Page 19
Clean and lubricate Chain Guide Bar and turn over.
Safety
Cleaning, Maintenance, and Lubrication Schedule
Note: This maintenance schedule is intended solely as duty cycle, temperature, air quality, and other factors. b. Setup
Operation
Maintenance
Item...
User Manual - Page 20
.../OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. Item 67255 THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Setup
Operation
Maintenance
Record Product's Serial...
User Manual - Page 21
... Circlip Ø 16
38 Output Shaft
Qty Part
Description
1
39 Gear
1
40 Trim Plate...62 Pump
1
63 Oil Plug Cover
1
64 Piston Support
1
65 Worm Gear Shaft
1
66 Worm Gear
1
67 Spring Washer ...
71 Chain Guide Bar
1
72 Saw Chain
1
73 Chain Guide Bar Sheath
1
74 Wrench
1
Qty
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 1 1 1 1 1 1 2 2 2 1 1 1 1 1
Setup
Operation
Maintenance
Item...
Harbor Freight Tools 67255 Reviews
We have not received any reviews for Harbor Freight Tools yet.