JET Tools JLP-075A-10 Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JLP-075A-10 manuals!
Problems with JET Tools JLP-075A-10?
Ask a Question
Free JET Tools JLP-075A-10 manuals!
Problems with JET Tools JLP-075A-10?
Ask a Question
Popular JET Tools JLP-075A-10 Manual Pages
User Manual - Page 1
M-187505 Revision B1 12/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
JLP-A Series Manual Lever Hoists/Pullers
1/4- to 6-Ton
JLP-25A 1/4-ton
JLP-75A 3/4-ton
(models shown are representative of the series)
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
...specifications listed in workmanship or materials subject to become inoperable within a
reasonable amount of our tools needs service or repair, please contact Technical Service by JPW Industries, Inc. Parts; Light-Duty Air Tools 1 Year - Heavy-Duty Air Tools... Technical Support Please contact Technical Service by a 90 day limited warranty against manufacturers' defects. JET woodworking ...
User Manual - Page 4
... . If used in conjunction with instructions and warnings may cause damage to "set forth in American National Standards titled ...support loads over sharp edges. If in service. 23. If the lever is centered between top and bottom hooks. 17. Do not place yourself or other object. 10. Prevent weld splatter upon the chain. 22. 1. Read and understand the entire owner's manual...
User Manual - Page 5
... following safety notices used in accordance with instructions set forth in serious or even fatal
Introduction
This manual is provided by JET covering the safe operation and maintenance procedures for quick reference:
Model No.:
Stock No.:
Purchased From:
Serial No.: Date Purchased:
The specifications in minor injury and/or possible tool damage. If there are any time...
User Manual - Page 6
Load Lift per Pull Lever
Std. Specify length when ordering.
6 Distance No. Min. Specifications (JLP-25A, -50A)
Stock Number Description
187740 JLP-25A-5 187505 JLP-50A-5 187506 JLP-50A-10
Rated Capcty.
(ton)
1/4
1/2
1/2
Lbs. chain is available in .) Weight "C" "D" "E" (lbs)
2.44 3.1 1.40 4.56
2.68 3.74 1.38 5.18
2.68 3.74 1.38 6.82
NOTE: The above stock ...
User Manual - Page 7
...models are representative; Specifications (JLP-75A, -150A, -300A, -600A)
Stock Number
Description
187606 JLP-75A-5 187607 JLP-75A-10 187608 JLP-75A-15 187609 JLP-75A-20 287606 JLP-75AWO-5 * 187610 JLP-150A-5 187611 JLP-150A-10 187612 JLP-150A-15 187613 JLP-150A-20 287610 JLP-150AWO-5 * 187614 JLP-300A-5 187615 JLP-300A-10 187616 JLP-300A-15 187617 JLP-300A-20 287614 JLP-300AWO-5 * 187618 JLP...
User Manual - Page 8
... or cracked.
5. Read this entire instruction manual thoroughly for shipping damage. See "Allowable Limits" on the surface, especially at the points where links contact each other. Contents of 30-weight oil to hook.
3. Periodically apply a light coat of the Carton
1 Lever Hoist 1 Owner's Manual 1 Warranty Card 1 Test Certificate
Installation
Support for the hoist may be...
User Manual - Page 9
... replacing, for your hoist clean and store in a clean, dry location.
9
Figure 3
If these sounds are worn and should not slip while using the hoist.
4. Free play is measured by a JET authorized service center.
3. The brake should be kept clean and free from dirt, water, and oil. Other Inspections
1. have it inspected and repaired...
User Manual - Page 10
... puller. Avoid lifting one load with the proper lift capacity. Figure 4 Figure 5
Figure 6
10 Move selector switch to raise or pull the load. Capacity of the safety latch (A, Figure 5)....the hook off the centerline (C, Figure 5).
• Never load the hook sideways (D, Figure 5).
3. Set the top hook securely.
2. Below is unavoidable, apply equal weight to the DOWN position and ratchet the...
User Manual - Page 12
...repair... shown in the model number). The slip ...before storage. Any load chain that are installed out-of-doors should not require any adjustment... Links Limit
Replace if ≥
2.433" 2.433" 3.629" 4.838" 6.058" 6.058"
Hook Wear Limits (Top and Bottom)
Replace the hook ... and should be replaced with calipers to rotate ...sizes.
Overload Protection
Some models of the JLP Lever Hoist have overload...
User Manual - Page 15
Parts List
Index No. Part... JLP25A-08 Change Over Gear 1 9 JLP25A-09 Lever Handle Bushing 1 10 JLP25A-10 Nut and Spring Washer M5 and 5 mm 2 11 JLP25A-11 Hex ... Plate 1 Pawl Pin...1 22 JLP25A-22 Chain Guide 2 23 JLP25A-23 Load Sprocket and Pinion Shaft...JLP-25A - specify length 4x12 mm 1 37 JLP25A-37 Chain Stop ...1
When ordering replacement chain (#36), specify length. 15
User Manual - Page 22
JLP-150A -
Parts List
Index No. Part No. Description
Size
Qty
2 JLP150A-02 Castle Nut (1.5T, 3T, 6T M10 1 3 JLP150A-03 Split ...-28A Load Sprocket (s/n 120606750 and higher 1 29 JLP150A-29 Roller Set (Right and Left 3x6 mm 74 30 JLP150A-30 Driving Pinion 1 31 JLP150A-31 Stripper ...1 32 JLP150A-32 Chain Guide Plate 1 34 JLP150A-34 Gear Side Plate Assembly 1 Gear Side ...
User Manual - Page 24
...6T 1 JLP300A-28A Load Sprocket (3T, 6T) (s/n 12043550 and higher 1 29 JLP300A-29 Roller Set (Right and Left) (3T, 6T 5x6 mm 60 30 JLP300A-30 Driving Pinion (3T, 6T ...1 31 JLP300A-31 Stripper (3T, 6T 1 32 JLP300A-32 Chain Guide Plate (3T, 6T 1 34 JLP300A-34 Gear Side Plate Assembly (3T, 6T 1 Gear Side ... (3T, 6T 2
24 JLP-300A - Parts List
Index No.
User Manual - Page 26
...6T 1 JLP300A-28A Load Sprocket (3T, 6T) (s/n 120615109 and higher 1 29 JLP300A-29 Roller Set (Right and Left) (3T, 6T 5x6 mm 60 30 JLP300A-30 Driving Pinion (3T, 6T ...1 31 JLP300A-31 Stripper (3T, 6T 1 32 JLP300A-32 Chain Guide Plate (3T, 6T 1 34 JLP300A-34 Gear Side Plate Assembly (3T, 6T 1 Gear Side ... (3T, 6T 2
26
JLP-600A - Parts List
Index No...
User Manual - Page 28
Having the Model Number and Serial Number of your hoist available when you call 1-800-274-6848, Monday through Friday (see our website for business hours, www.jettools.com). Ordering Parts
To order parts or reach our service department, call will allow us to serve you quickly and accurately.
427 New Sanford Road LaVergne, Tennessee 37086
Phone: 800-274-6848 www.jettools.com 28
JET Tools JLP-075A-10 Reviews
We have not received any reviews for JET Tools yet.