Lantronix Micro Support and Manuals
Get Help and Manuals for this Lantronix item
View All Support Options Below
Free Lantronix Micro manuals!
Problems with Lantronix Micro?
Ask a Question
Free Lantronix Micro manuals!
Problems with Lantronix Micro?
Ask a Question
Popular Lantronix Micro Manual Pages
Micro - Product Brief - Page 1
...core competencies. So why build it yourself when there is available for Ethernet access. Lantronix embedded device networking products provide proven, integrated hardware and software solutions for easy software upgrades Custom protocol support available
Embedded Device Server™ Micro
Design Ethernet Connectivity into a product is a header, providing connections to Ethernet networks...
Micro - Product Brief - Page 2
..., RoHS Micro with 2 Serial Port support, RoHS Micro with no LEDS, but instead, Header Pins on the TTL side, RoHS Micro, Pin Header on TTL side instead of RJ45) Pin Function 1 TX+ 2 TX3 RX+ 4 RX- All rights reserved. 910-300 05/06 DGS2500 Lantronix is a registered trademark and Device Server is a trademark of their respective owners. Specifications subject...
Embedded Integration Kit (EIK) - User Guide - Page 3
... 3-8
Additional Settings 3-8
Factory Settings 3-9
Update Settings 3-9
4: Using Setup Mode for Configuration
4-1
Accessing Setup Mode 4-1
Using a Telnet Connection 4-1
Using the Serial Port 4-2
Server Configuration (Network Configuration 4-3
IP Address 4-3
Set Gateway IP Address 4-3
Netmask: Number of Bits for Host Part 4-3
Change Telnet Configuration Password 4-3
DHCP...
Embedded Integration Kit (EIK) - User Guide - Page 5
... set parameters such as port and server properties.
4:Using Setup Mode
5:Updating Firmware 6:Monitoring the Network 7:Troubleshooting
Provides instructions for obtaining the latest firmware and updating the device server. Provides instructions for accessing and using the command line interface for monitoring the network and diagnosing problems.
Describes common problems and error messages...
Embedded Integration Kit (EIK) - User Guide - Page 8
... the specific unit. There are unique numbers assigned to each time it must have a unique IP address on the network. If you use DHCP, the device server is assigned a new IP address each unit.
00-20-4A-14-01-18 or 00:20:4A:14:01:18
IP Address
Every device connected to as a Lantronix...
Embedded Integration Kit (EIK) - User Guide - Page 9
... port. 3. Hardware Address: 00-20-4a
Embedded Integration Kit User Guide
3-1 Physically Connecting the Unit
The following diagram shows a properly installed CoBox-Micro. Figure 3-1 - Connect an Ethernet cable to Serial Device and Network
10/100 Ethernet
+5
J 1 CON2
RS232
1. Supply power to get an embedded device server online and working.
It is on the product label.
Other...
Embedded Integration Kit (EIK) - User Guide - Page 14
... port 9999.
Getting Started
Server Properties
In the Telnet Password field, enter a password to prevent unauthorized access to the Setup Mode via a serial connection. The password is limited to 4 characters. (An enhanced password setting of 16 characters is available under Security Settings on the Telnet Setup Mode window.) Note: You do not need a password to access the Setup Mode window via...
Embedded Integration Kit (EIK) - User Guide - Page 33
... Integration Kit User Guide
Once you have obtained the firmware with encryption, you are using a Lantronix-supplied encryption library or a Lantronix device server configured with an identical encryption string are echoed as the Advanced Encryption Standard (AES) to be set. Rijndael is supported without saving. Figure 4-9.
This setting defaults to enable the encryption...
Embedded Integration Kit (EIK) - User Guide - Page 38
... the firmware file in the Source File field.
4. In the Destination File field, do one of the unit being upgraded.
6. Via Another Unit
Note: This procedure works for all of the embedded device servers except the Micro100. Enter the host unit's Monitor Mode.
2.
Make sure the Put and Binary options at ftp://ftp.lantronix.com...
Embedded Integration Kit (EIK) - User Guide - Page 44
...) is not blocked with your serial device attached to use the correct setting in the Binary to the correct from the device server by looking
socket of the device server.
See the full list of the device server. Try upgrading the firmware again, but you try to the device server from the device server. Embedded Integration Kit User Guide
3
Use Connect Mode option C1 or...
Embedded Integration Kit (EIK) - Integration Guide - Page 6
... the following:
‹ An embedded device server: CoBox-Micro, Micro100, CoBox Mini, or CoBoxMini100
‹ Board carrier unit with their products prior to test the embedded device server on kit) ‹ DB9 to interface our product with your product. Embedded Integration Kit Integration Guide
1-1 1: Introduction
Embedded Integration Kits
The Lantronix Embedded Integration Kits (Mini-Kit...
Embedded Integration Kit (EIK) - Integration Guide - Page 7
....
Device Installer User Guide
Provides instructions on using the Windows-based utility used to create a virtual com port.
1-2
Embedded Integration Kit Integration Guide
Com Port Redirector User Guide
Provides information on using the Windows-based utility to configure Lantronix embedded device servers.
Provides general guidelines to configure, use, and update the firmware.
Embedded Integration Kit (EIK) - Integration Guide - Page 9
... Guide CoBox-Micro Connectors
12
CON1
(TTL)
11
CON2 (RJ45) 4 3
2 21
1
87
21 S1
CON3
CON4 (LEDs)
The CoBox-Micro that comes with customized connector configurations. CON1 TTL Serial Port (DIL 2 x 6 Pins) Pin Signal
1 +5VDC
Table 2-1.
Figure 2-3. The Embedded Integration Kit (part number Micro-Kit) includes the CoBox-Micro embedded device server. CoBox-Micro Connector...
Embedded Integration Kit (EIK) - Integration Guide - Page 22
...). Technical Specifications
Category Memory Serial Flash Serial Interface Board Dimensions Weight Temperature Protocols Supported Network Interface Data Rates Serial Line Formats
Modem Control Flow Control
Management
System Software LEDs
Compatibility Power Requirements
Table 3-4. Revision Number
Part Number Manufacturing Code
MAC Address
Embedded Integration Kit Integration Guide
3-7
Embedded Integration Kit (EIK) - Integration Guide - Page 44
...CoBox network connector
digital ground and power Plane (inner layer)
shield planes
inner layer signal traces
Virtual Ground
The device servers...device server to the RJ45 should be connected to the RJ45s shield or to a virtual ground signal provided by the device server. (See also next section and product-specific...Guide...parts of two capacitors (ceramic 0.1 µF) conducted symmetrically to 100...
Lantronix Micro Reviews
We have not received any reviews for Lantronix yet.