Rane AC 22S Support and Manuals
Get Help and Manuals for this Rane item
Popular Rane AC 22S Manual Pages
Operation Manual - Page 1
... / HIGH
300
400
250
500
180
700
120
1.0k
90
1.5k
80
2.0k
75
3.0k
70
3.6k
FREQUENCY
MID / HIGH
HIGH
46
2
8
0 10 LEVEL
HIGH
AC 22S
ACTIVE CROSSOVER
POWER
AC 22S
ACTIVE
CROSSOVER
Operation Manual - Page 2
... SAFETY INSTRUCTIONS
1. Install in a residential installation. The wide blade or third prong is present within this apparatus near any ventilation openings. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with manufacturer's instructions. 8. Servicing is required when the apparatus has been damaged in any way, such as power supply cord...
Operation Manual - Page 4
...the back of the midrange filter. WEAR PARTS: This product contains no wear parts.
When operated in the MONO 3-WAY position. OPERATORS MANUAL
AC 22S
ACTIVE CROSSOVER
CH 1 MASTER
46
2
8
0 ... HIGH
POWER
AC 22S
ACTIVE
CROSSOVER
QUICK START
The AC 22S can be set for more information on cabling and grounding requirements. To keep operation simple, remember this manual for STEREO 2-WAY....
Operation Manual - Page 5
...
3.6k
FREQUENCY
MID / HIGH
HIGH
46
2
8
0 10 LEVEL HIGH
7
POWER
AC 22S
ACTIVE
CROSSOVER
Observe the labels screened above the controls for stereo operation.
1 CHANNEL 1 MASTER LEVEL controls the overall Level of Channel 1 without altering relative settings of the HIGH and LOW Outputs.
8 POWER indicator: If the power cable is plugged in position, all LEVEL controls is at...
Operation Manual - Page 6
...(USA domestic).
Channel 2 LOW OUT is set to MONO SUB, only use Channel 1 LOW OUT. Do not lift the ground connection! Manual-3 The result is subject to the right channel...Part 15 of the low frequency amp. REAR PANEL: STEREO 2-WAY CONFIGURATION
2-way operation: read the top row
1 Right Input
100-240 V
COMMERCIAL AUDIO
50/60 Hz 7 WATTS EQUIPMENT 24TJ
R
AC 22S
MADE IN U.S.A. RANE...
Operation Manual - Page 7
...
2
8
0 10 LEVEL HIGH
678 9 0
POWER
AC 22S
ACTIVE
CROSSOVER
q
Observe the labels below the controls for Mono operation.
1 CHANNEL 1 MASTER LEVEL controls the overall Level without altering the relative settings of signal going to the HIGH Output only. Refer to Time Delay Adjustment on page Manual-6 for procedure.
9 MID / HIGH FREQUENCY: sets the crossover Frequency between LOW and MID...
Operation Manual - Page 8
... this device may cause undesired operation. Manual-5 REAR PANEL: MONO 3-WAY CONFIGURATION
100-240 V
COMMERCIAL AUDIO
50/60 Hz 7 WATTS EQUIPMENT 24TJ
R
AC 22S
MADE IN U.S.A. Operation is subject to... SWITCH MUST BE SET TO 2- RANE CORP. This mates with Part 15 of the low frequency amp.
5 MODE switch: Set this switch for MONO 3-WAY operation.
6 SUBWOOFER switch: Set this switch for ...
Operation Manual - Page 9
... all the main lobes are supplied in many cases it is possible that the exact recommended Crossover Frequency may be sure that all the drivers vertically lined up with 41 choices it works! Setting Delay controls by no hazard to the driver or degradation in crossovers. The AC 22S utilizes 41‑detent crossover Frequency selectors which narrow the...
Operation Manual - Page 10
... analyzer, pink noise generator and flat response microphone to set the analyzer display level control so the readout corresponding to ±3 dB on the crossover so pink noise is heard from only the mid driver at the crossover frequency:
i. Manual-7
The procedure applies to match your specific crossover points than +3 dB reading, slowing turn up the MID...
Operation Manual - Page 11
... throughout the test, so affix it up causes the lower frequency driver to move the high driver, then you obtain a 0 dB reading on the crossover so that the meter remain in the AC 22S is then repeated for some reason inappropriate, an accurate Delay setting can be obtained by the tone generator.
Adjust the SPL meter...
Operation Manual - Page 12
... system in the AC 22S is necessary; Manual-9
Once all of common speaker configurations;
The amount of the stack.
b. Subwoofers will have to change relative positions, then you will often possess long folded or straight horns, resulting in balancing the speaker stack. If the meter reads +3 dB, then the drivers are set, then re‑...
Operation Manual - Page 13
...
21"
8 8 8 MAX MAX MAX
Displacement
7k 1.2 MAX
24"
MAX MAX MAX
Manual-10
Fig. 3.
Pink noise can be used if all other frequencies are electronically aligned and...setting corresponding to a 9" displacement at the crossover frequency. When both drivers. then the two drivers are disregarded, since room acoustics and imperfect driver response will then be "5" as a source, each driver...
Operation Manual - Page 14
...of setting the crossover Output Levels. Setting Levels With a Realtime
Analyzer
NOTE: If you profess, the absolute importance and effectiveness of some kind of active crossovers. Set all crossover ...set the crossover, set the HIGH LEVEL control for all LEVEL controls to be corrected by the crossover. IMPORTANT: Compression driver or horn roll‑off, bass roll‑off problem...
Operation Manual - Page 15
... each crossover section to "down point of driver response. 1. Find the frequency at soldering. For a Mono 3-Way system with a chart showing a frequency response curve. Install the capacitor, and solder the leads from that it reads 0 dB on the high output, only place C54 in the AC 22S to "C-weighting", "slow" if those switches are set for...
Rane AC 22S Reviews
We have not received any reviews for Rane yet.