Sony ICP-X7000 Support and Manuals
Get Help and Manuals for this Sony item
View All Support Options Below
Free Sony ICP-X7000 manuals!
Problems with Sony ICP-X7000?
Ask a Question
Free Sony ICP-X7000 manuals!
Problems with Sony ICP-X7000?
Ask a Question
Popular Sony ICP-X7000 Manual Pages
Users Guide - Page 16
...] and [Initial Status Define 562 Data Saved by [Setup Define 562 Data Saved by [Initial Status Define]........563 Error Messages 565 Error Messages Displayed in the Error Status/
Error Log Menu 565 Error Messages Appearing in a Message
Box 566 Error Messages Shown in the Error
Information Menu 575 Maintenance 576
Replacing Keytop Labels 576 Cleaning the Control Panel 576...
Users Guide - Page 17
Overview
1 Chapter
Introduction
This manual is the User's Guide for system features
System with installed option 4K system boards and settings to support 4K format
System with installed option HD system boards and settings to support HDTV format
System with installed option SD system boards and settings to support SDTV format
A system in which the control 6M/E system panel has six M/E banks...
Users Guide - Page 66
...Function grouping
(functions of the HF buttons at the bottom of the control panel setup.
Returning Settings to Default Values
Press [Default Recall], turning it on menus that can position ... >Shortcut menu (0021).
2 Select a group in the same way as part of the screen) • When a parameter setting button is pressed in relation to adjust the value, then left decreases the ...
Users Guide - Page 122
.... When DME is replaced by the key fill and key edge fill state.
1 Open the M/E-1 >Key1 >Transition menu (1116).
2 In the group, select a blink effect. Key Blink: Sets key blinking. Note...
If the input signal and AUX bus color corrector is enabled in the Setup menu, the video process of each switcher bank cannot be used....
Users Guide - Page 217
... be selected.
• Screen aspect, show key, and [MACRO ATTACH ENABLE] button settings are common to main and sub.
• If a snapshot is recalled simultaneously for ... is executed with different M/E Config settings are recalled:
- Similarly, those created when the signal format is other than 1080P. M/E-1 to four levels.
M/E Config - Not supported Not supported
a) Key 2 to key 8 ...
Users Guide - Page 220
...the Engineering Setup >Switcher >Config >Logical M/E Assign menu (7331.5).
220 Item Keys
Resizer Wipes DME Wipes Frame memory
Restrictions
• Wipe pattern keys not supported • Filter parameter settings for
luminance keys, linear keys, and chroma keys not supported • Y Filter and C Filter parameters for color vector keys not supported • [Key Position] settings for luminance...
Users Guide - Page 272
... the Non Linear >Melt
menu (4141.27), select the melt method. Applying the Melt effect
1 In the group of jaggedness at melted
part
3 To make transition settings, press [Transition] and set the following parameters.
To stop the wave in center of swirl
3 Outer
Amount of rotation outside of Area
4 Area
Region of swirl...
Users Guide - Page 303
... VTR, Extended VTR, or disk recorder in this system, the following manual operations and timeline settings. • Controlling manually from the utility/shotbox control block (Cueup & Play and VTR/disk ...register, then recalling the register to the start point when playback of the start point. Update the timecode of a frame memory clip finishes, and repeat playback in VTR/disk recorder...
Users Guide - Page 398
You must manually delete both files...7151).
2 Press [File Edit].
In the device selection area, press [DEFAULT] (default setting), then select the target folder in the 1080P signal format, there are two still image...delete the other paired file.
For frame memory file operations, frame memory folder specification and data type selection is not possible to 8 characters in the frame memory...
Users Guide - Page 405
... is necessary to set in the Engineering Setup >System menu (see page 421).
• The signal format for the 2nd switcher cannot be connected is always DME1 (unit ID: 1), supporting four channels.
Note... control panels that can be connected can connect up to four MVE-8000A units to the installation manual for 1st switcher (Ch7/8)
Unit ID 4
Notes
• When the signal format is ...
Users Guide - Page 413
...] is selected: In each of the to the
selection in non-volatile memory or ROM within each channel on . You can set Setup mode and Initial Status mode settings separately. • Setup mode: Set one of the following states of each device when the system is only available for the DME.
4 Perform the following operations...
Users Guide - Page 422
...]. Note that it is not possible to set as the primary device automatically In the group, press [Auto Detect]. Changing the lock password
1 In the Engineering Setup >System >Maintenance
>Setup Operation Lock menu (7317.1), press [Change Password].
2 Check the message, then press [Yes].
3 Follow the on-screen instructions to 16 characters in the File menu. Always...
Users Guide - Page 423
...displayed menu is locked, press [Lock] and enter the password. To set a lock candidate, first remove the lock in the Setup Operation Lock menu (7317.1). Locking File Loading Operations
You... the lock password
1 In the Engineering Setup >System >Maintenance
>File Load Lock menu (7317.2), press [Change Password].
2 Check the message, then press [Yes].
3 Follow the on-screen instructions to white....
Users Guide - Page 549
...at the same time as Key Border. Editor port usage
7344
Yes
settings
1080P support
7313
Yes
MVE-9000 Yes Cannot be enabled at the same time as Key Border. Combiner [Depth]... (Spotlighting)
Edge softness function 7334
No
enable/disable
AUX bus output/re-entry 7337.7 input settings
DME1 to 8 Ext In settings supported No
Yes
No
No
Yes
See page page 258 page 259
page 294
page 417 page 466...
Operating Instructions - Page 23
... installs into the MKS-X7700 for remote connector expansion.
ICP-X7000 Integrated Control Panel Pack
General
Power requirements 1) 42.5 V to change without notice.
MKS-X7032 Key Fader Module A module for key adjustments and other operations. Specifications
Design and specifications are not filled by the modules in the "LICENSE" folder on the CD-ROM. The source code...
Sony ICP-X7000 Reviews
We have not received any reviews for Sony yet.