JET Tools JWL-1221VS Support Question
JET Tools JWL-1221VS Support Question
Find answers below for this question about JET Tools JWL-1221VS.Need a JET Tools JWL-1221VS manual? We have 1 online manual for this item!
Question posted by dlspigiel on April 23rd, 2018
Replace Circuit Board Assembly On Jet Lathe 1221 Vs
are there any videos on how to replace the circuit board asse
Current Answers
Related JET Tools JWL-1221VS Manual Pages
User Manual - Page 1
This .pdf document is bookmarked
Operating Instructions and Parts Manual
12x21-inch EVS Woodworking Lathe
Model JWL-1221VS
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No. M-719200 Revision C1 12/2014 Copyright © 2014 JET
User Manual - Page 2
... are given as expendable parts or accessories expected to effect at 1-800-274-6846 for industrial or commercial purposes 5 Year -
Pro-Duty Air Tools 2 Year - Hand Tools
NOTE: JET is Covered This warranty covers any reason whatsoever.
How State Law Applies This warranty gives you will explain and assist with your product or...
User Manual - Page 3
... ...22 15.0 Troubleshooting the JWL-1221VS Lathe 23 16.0 Replacement Parts...24 16.1.1 Bed Assembly - Parts List ...26 16.2.1 Headstock Assembly - Parts List ...30 17.0 Electrical Connections...31
3 Exploded View 30 16.3.2 Controller Assembly - JWL-1221VS lathe ...7
6.1 Hole pattern - Exploded View 28 16.2.2 Headstock Assembly - JWL-1221VS lathe 6 6.0 Specifications -
User Manual - Page 4
...the machine is designed and intended for other purposes, JET disclaims any real or implied warranty and holds itself harmless... on the machine and in the OFF position before attempting assembly or operation.
2. Your risk of moving parts. 9. Remove...replaced.
16. Looking around the machine clean and free of parts, mounting and any injury that use this lathe. The right tool...
User Manual - Page 5
...32. Read and understand the entire contents of the type necessary for a JET Model JWL-1221VS Lathe. Keep work pieces from experienced users or trade articles. Retain this manual for...the power off the machine before attempting assembly or operation! Don't use your local supplier or JET. Check the workpiece carefully for the work. Adjust tool rest to a complete stop a ...
User Manual - Page 6
... readout 24. Index pin 3. Headstock 6. Spur center 16. Tool rest 17. Faceplate 15. Warning label 12. Lower pulley access door 13. Forward/reverse switch 23. Tool rest base locking handle 26. DC motor 11. Tool caddy
Figure 1
14. Bed 7. Tool rest locking handle 18. Variable speed dial (potentiometer) 21. Belt tension release lever
6 JWL-1221VS lathe
1.
User Manual - Page 7
... 14.75" (375 mm) Stand footprint 30-1/2"L x 9"W (775 x 229 mm) Tool support post diameter ...5/8" (15.9 mm) Overall dimensions, assembled 33.6"L x 11"W x 17.7"H (853 x 280 x 450 mm) Overall dimensions of... of our policy of continuous improvement, JET reserves the right to local/national electrical codes.
JWL-1221VS lathe
Model number ...JWL-1221VS Stock number ...719200
Motor and electricals...
User Manual - Page 8
6.1 Hole pattern - JWL-1221VS lathe
Figure 2 Clearance hole spacing for mounting lathe
8
User Manual - Page 9
... safety instructions.
7.1 Shipping contents
Carton contents (see section 14.0) or a work table, using handwheel, until the Lathe is assembled and running properly.
Compare the contents of lathe with a protectant. A 1 Spur center - B 1 Spindle Wrench - D 2 Tool caddies -
Push in spindle lock (A) and rotate spindle
using the four threaded holes in faceplate (or chuck...
User Manual - Page 11
...shown in A, Figure 9. All Grounded, Cord-connected Tools:
In the event of a malfunction or breakdown, ...replace damaged or worn cord immediately.
2. 8.0 Electrical connections
The JWL-1221VS JET lathe is rated for electric current to reduce the risk of electric shock.
It is recommended that have the proper outlet installed by a
Figure 9
8.2 Extension cords
The use on a circuit...
User Manual - Page 12
... increase risk of pulley access door. 9.0 Adjustments
Make sure all levers and locking handles are tightened before operating the lathe.
9.1 Tool rest
Referring to Figure 10:
The tool rest assembly is designed to allow adjustment for height, position on tool rest base to slide base forward or back, and to angle it to the bed.
User Manual - Page 13
...Figure 15)
4. Figure 14
9.4 Index pin
Referring to Figure 15: Indexing is secured between lathe centers. Rotate knurled head counterclockwise until index pin (I) aligns with a hand-held router, while ...) can be removed to engage threads and secure in a work piece, while keeping the lathe spindle locked; If a power outage should occur during operation.
Use spindle lock for this ...
User Manual - Page 14
...rest in the craft.
11.1 Inspection
Before operating the lathe, check that everything is essential to get red hot. Tool support; should be acquired. Lighting; As one place on...bowls, round edges of specialty tools for cooling. Square Scraper (Bedan) - 3/8" or 1/2", used to make a cut -off, or to be quenched for specific applications can replace the knowledge gained by conversation with...
User Manual - Page 15
... to hold the workpiece securely in place. Be careful that it is mounted in the Lathe spindle. Advance the tailstock spindle with the attached workpiece) into position. The tailstock ram ... mallet or dead blow hammer as in Figure 20. Tighten the spindle locking handle. Move tool support into the headstock spindle.
7. 11.3 Spindle Turning
Spindle turning takes place between the...
User Manual - Page 20
...lathe from power. 2. Figure 29
8.
Disconnect lathe from power.
2. Engage spindle lock, and loosen both setscrews (B) in handwheel with 3mm hex key. Loosen both set
screws (A) in spindle pulley. 7. Figure 30 9.
A heavily worn or damaged brush, if allowed to remain, may pop out with the spindle. Inspect brush. Figure 28
12.3 Belt replacement...replacing, replace.... Replace brush...
User Manual - Page 22
Contact your lathe. Stand Extension for JWL-1221VS Lathe
# 719203 - Stand for JWL-1221VS Lathe 22 Bed Extension (22-1/2") for JWL-1221VS Lathe
# 719202 - 14.0 Optional accessories
These accessory items, purchased separately, can enhance the functionality of your dealer to order, or call JET at the phone number on the cover. # 719201 -
User Manual - Page 23
...
Voltage too high
Overload limiter in circuit board activated Spindle sensor not working
Reduce depth of cut
Check connectors of oil to lathe bed surface.
Replace motor Reduce depth of cut
Improper belt adjustment, or worn or broken belt
Correct overload condition
Increase supply wire size. 15.0 Troubleshooting the JWL-1221VS Lathe
Table 3
Trouble
Probable Cause
Remedy...
User Manual - Page 24
... working
E8 shown on the following pages. Having the Model Number and Serial Number of motor cord is connected Replace circuit board
16.0 Replacement Parts
Replacement parts are listed on digital readout
Spindle locked Motor cord unplugged
Circuit board burned out
Remedy
Check connectors of motor sensor cord to switch box Readjust sensor closer to sensor collar...
User Manual - Page 30
...5 JWL1221VS-305....... Pan Head Screw M3x20 2 6 JWL1221VS-306....... Exploded View
16.3.2 Controller Assembly - Controller Assembly (includes #1 thru #15 1 1 JWL1221VS-301....... Main Switch 1 9 JWL1221VS-309....... Control Panel Label 1 10 JWL1221VS-310....... Circuit Board Assembly (serial # 1304627 and higher 1 14 JWL1221VS-321....... Tapping Screw M3x19 4 3 TS-1540011...
User Manual - Page 31
BLACK
GREEN
M+
WHITE
Run/Stop Switch
MOTOR
GREEN
GREEN
31 17.0 Electrical Connections
SENSOR SPINDLE
SENSOR MOTOR
VR POTENTIOMETER
BLACK
S-S
M-S
BLUE(CW) RED (V+)
FWD/REV Switch
VR
LI-SW
Digital Readout
WHITE
N
L
GND PRINTED CIRCUIT BOARD
M-
Similar Questions
Isometric Drawing For 18" Jet Bandsaw Blade Guide
I need the drawing for re asse
I need the drawing for re asse
(Posted by Andrewsmarlin 1 year ago)
Free Spool
I have a Jet model JLP-150A that want release to free spool. This unit does not have the separate pr...
I have a Jet model JLP-150A that want release to free spool. This unit does not have the separate pr...
(Posted by dce1414 2 years ago)
Replacing The Controller In A Jet 1221vsr Lathe.
Which sensor plugs into which connector on the controller?
Which sensor plugs into which connector on the controller?
(Posted by crackerjack22470 2 years ago)
What Type Of Coupon Codes Does Jet Tools Offer?
What is the best place to go to find JET Tools coupon codes?
What is the best place to go to find JET Tools coupon codes?
(Posted by Anonymous-154243 10 years ago)
How Can I Find Unbiased Jet Tools Reviews?
I am looking into JET Tools, but would like to read honest ratings and reviews first.
I am looking into JET Tools, but would like to read honest ratings and reviews first.
(Posted by Anonymous-154240 13 years ago)