JET Tools JWL-1221VS Support Question
JET Tools JWL-1221VS Support Question
Find answers below for this question about JET Tools JWL-1221VS.Need a JET Tools JWL-1221VS manual? We have 1 online manual for this item!
Question posted by crackerjack22470 on November 12th, 2021
Replacing The Controller In A Jet 1221vsr Lathe.
Which sensor plugs into which connector on the controller?
Current Answers
Answer #1: Posted by SonuKumar on November 13th, 2021 6:16 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,619,300
Member since:
May 9th, 2021 Points: 16,619,300
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Answer #2: Posted by Technoprince123 on November 12th, 2021 8:26 AM
Technoprince123
Member since:
February 8th, 2021 Points: 1,205,190
Member since:
February 8th, 2021 Points: 1,205,190
Please response if this answer is acceptable and solw your problem thanks
Related JET Tools JWL-1221VS Manual Pages
User Manual - Page 1
M-719200 Revision C1 12/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
12x21-inch EVS Woodworking Lathe
Model JWL-1221VS
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
... IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. Machine Accessories;
More Information JET is a division of maintenance. Consumable items; JET Parallel clamps; Manual Hoist Accessories;
Pro-Duty Air Tools 2 Year - Hand Tools
NOTE: JET is constantly adding new products. This warranty does not cover failures due directly or indirectly to -date...
User Manual - Page 3
... pattern - Exploded View...25 16.1.2 Bed Assembly - Exploded View 30 16.3.2 Controller Assembly - Parts List ...30 17.0 Electrical Connections...31
3 JWL-1221VS lathe...8 7.0 Setup and assembly...9
7.1 Shipping contents...9 7.2 Mounting lathe to stand/table ...9 7.3 Installing tool caddies ...9 7.4 Installing/removing face plate ...9 7.5 Installing/removing spur center ...10 7.6 Installing...
User Manual - Page 4
...; Make all of checking to cause cancer, birth defects or other purposes, JET disclaims any real or implied warranty and holds itself harmless from that are :...tools with approved safety equipment, such as face or dust masks that use this lathe. 9. This lathe is properly grounded.
12. Remove adjusting keys and wrenches. Check damaged parts. Provide for use extreme caution and replace...
User Manual - Page 5
... with the following safety notices used , always make personal safety a priority. 25. Adjust tool rest to be reached at our web site: www.jettools.com. This means that if precautions... are not heeded, it . Read and understand the entire contents of the type necessary for a JET Model JWL-1221VS Lathe. Serious injury could occur if the machine tips over.
27. Don't use your hands.
26....
User Manual - Page 6
... 19. Belt tension release lever
6 Live center 8. Tailstock 9. Tool caddy
Figure 1
14. Speed chart 4. Tool rest locking handle 18. Forward/reverse switch 23. Index pin 3. Tailstock handwheel 10. Lower pulley access door 13. Tool rest base locking handle 26. 5.0 Features and nomenclature - Faceplate 15. Tailstock locking handle 20. JWL-1221VS lathe
1.
User Manual - Page 7
...JWL-1221VS lathe
Model number ...JWL-1221VS Stock number ...719200
Motor and electricals: Motor type ...120V DC Horsepower...1 HP Phase ...single Voltage ...115V only Cycle ...60Hz Listed FLA (full load amps) ...6 A Power transfer...belt On/off switch ...paddle style with safety key Power cord length ...6 ft. (183cm) Power plug...cast iron and steel Tool support ...cast iron Tool support base ...cast...
User Manual - Page 8
6.1 Hole pattern - JWL-1221VS lathe
Figure 2 Clearance hole spacing for mounting lathe
8
User Manual - Page 9
... shipping agent. Missing parts, if any, should be removed with a protectant. C 1 Knockout rod - H 1 Owner's manual 1 Warranty card
Tools required for correct spacing of the lathe, such as it will be drilled in the worktable.
7.3 Installing tool caddies
Referring to loosen, and may result in spindle lock (A) and rotate spindle
using the four threaded...
User Manual - Page 11
...
The JWL-1221VS JET lathe is not permitted in Canada. It is recommended that is properly installed and grounded in accordance with all local codes and ordinances. The plug must be...replacement of the power source. Local codes take precedence over recommendations. This adapter is rated for electric current to carry the current your product will draw. All Grounded, Cord-connected Tools...
User Manual - Page 12
... 12
Figure 10
9.2 Tailstock
Referring to a different pulley: 1. This chart is no torque on tool rest base to slide base forward or back, and to angle it to Figures 13 and 14: The lathe has three speed ranges, controlled by the manufacturer. Adjust cam lock nut (Figure 12) as follows: (H) 600220, (M) 300-110...
User Manual - Page 13
... 2. Make sure belt is properly seated in position. 3. for example, when cutting flutes on the lathe. Move pulley to engage threads and secure in both pulleys, and both pulleys are identified by pulling...as viewed from tailstock end.
It is the normal rotation for this purpose.
10.0 Operating controls
Referring to Figure 16:
Speed dial (A): Rotate dial to full speed. If a power outage...
User Manual - Page 14
...keep clean, use a mill file to sharpen tools freehand. The following tools provide the basics for specific applications can be located near your lathe and at a comfortable height. Square Scraper ...shadows and reduce eye strain.
11.2 Turning Tools
If possible, select only quality, high-speed steel turning tools.
Carbon steel tools can replace the knowledge gained by conversation with a 60...
User Manual - Page 15
... sure the headstock is mounted in place. Advance the tailstock spindle with the tailstock to the Lathe bed.
5. Tighten support base to the bed.
8. Figure 18 shows the basic profile shapes... of the spur center and the inside of the lathe. Tighten the spindle locking handle. Use enough pressure to a cylinder. 1. Move tool support into the ends of exerting excessive pressure against ...
User Manual - Page 16
... work -piece, never start in a continuous motion to rough the piece down to ensure control and avoid catches. Roll the tool in a burned or burnished "V" with a large roughing gouge. Coves
1. With the flute... the tool on the tool support with the workpiece to a
cylinder, smooth it up at 90 degrees to the workpiece, touch the point of the tool to make cut . Start lathe at the...
User Manual - Page 18
... half along the pith to control than other gouges. This will find good, sound wood. The deep fluted bowl gouge is best to start with each tool before attempting to accomodate attaching ...jaw scroll chucks with the 1/2" deep fluted bowl gouge, holding a block of gouges. Start lathe at a time. Once turning becomes comfortable, try green wood which cuts very easily. Most average...
User Manual - Page 19
...lathe back on tool support at the rim). Apply second finish coat and allow to fit your elbow.)
2. As the tool goes deeper into the bowl, progressively work deeper into the bowl.
(NOTE: Try to make it moves deeper into the bowl to control... cutting edge of gouge, while right hand swings tool handle around toward the four o'clock position, ...
User Manual - Page 20
Reinsert brush, or install new one, and screw in spindle sensor collar (C). NOTE: When cover is worn 1/4" (6mm) or more, collapsed ...Release belt tension (see Figure 14), and
open pulley access doors. 3. Inspect brush. Disconnect lathe from power.
2.
If brushes need replacing, replace both set
screws (A) in spring, abnormal discoloration, signs of the motor.
turn clockwise to ...
User Manual - Page 22
Bed Extension (22-1/2") for JWL-1221VS Lathe
# 719203 - Stand for JWL-1221VS Lathe
# 719202 - Stand Extension for JWL-1221VS Lathe 22 14.0 Optional accessories
These accessory items, purchased separately, can enhance the functionality of your dealer to order, or call JET at the phone number on the cover. # 719201 - Contact your lathe.
User Manual - Page 23
... bearings Worn motor Workpiece warped, out of oil to sensor collar Replace sensor collar (p/n JWL1221VS110) Replace sensor set too far from work piece
Use correct tool for turning Worn spindle bearings Worn drive belt Motor mounting fasteners are loose Lathe on uneven surface Dull tools Tool support set too low Tool support set (p/n JWL1221VS112)
23
Re-apply light coat of...
Similar Questions
Isometric Drawing For 18" Jet Bandsaw Blade Guide
I need the drawing for re asse
I need the drawing for re asse
(Posted by Andrewsmarlin 1 year ago)
Free Spool
I have a Jet model JLP-150A that want release to free spool. This unit does not have the separate pr...
I have a Jet model JLP-150A that want release to free spool. This unit does not have the separate pr...
(Posted by dce1414 2 years ago)
Replace Circuit Board Assembly On Jet Lathe 1221 Vs
are there any videos on how to replace the circuit board asse
are there any videos on how to replace the circuit board asse
(Posted by dlspigiel 6 years ago)
What Type Of Coupon Codes Does Jet Tools Offer?
What is the best place to go to find JET Tools coupon codes?
What is the best place to go to find JET Tools coupon codes?
(Posted by Anonymous-154243 10 years ago)
How Can I Find Unbiased Jet Tools Reviews?
I am looking into JET Tools, but would like to read honest ratings and reviews first.
I am looking into JET Tools, but would like to read honest ratings and reviews first.
(Posted by Anonymous-154240 13 years ago)