JET Tools JWL-1221VS Support and Manuals
Get Help and Manuals for this JET Tools item
View All Support Options Below
Free JET Tools JWL-1221VS manuals!
Problems with JET Tools JWL-1221VS?
Ask a Question
Free JET Tools JWL-1221VS manuals!
Problems with JET Tools JWL-1221VS?
Ask a Question
Most Recent JET Tools JWL-1221VS Questions
Replacing The Controller In A Jet 1221vsr Lathe.
Which sensor plugs into which connector on the controller?
Which sensor plugs into which connector on the controller?
(Posted by crackerjack22470 2 years ago)
Replace Circuit Board Assembly On Jet Lathe 1221 Vs
are there any videos on how to replace the circuit board asse
are there any videos on how to replace the circuit board asse
(Posted by dlspigiel 6 years ago)
Popular JET Tools JWL-1221VS Manual Pages
User Manual - Page 1
M-719200 Revision C1 12/2014 Copyright © 2014 JET This .pdf document is bookmarked
Operating Instructions and Parts Manual
12x21-inch EVS Woodworking Lathe
Model JWL-1221VS
JET 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.jettools.com
Part No.
User Manual - Page 2
...tools needs service or repair, please contact Technical Service by a 90 day limited warranty against manufacturers' defects.
More Information JET is designed to parts, fittings, and accessory equipment which varies in the literature included with a Five Year Warranty that are used for the time period specified in duration based upon the product. (See chart below . The specifications...
User Manual - Page 3
... Warranty and Service...2 2.0 Table of workpiece 21 14.0 Optional accessories ...22 15.0 Troubleshooting the JWL-1221VS Lathe 23 16.0 Replacement Parts...24 16.1.1 Bed Assembly - JWL-1221VS lathe...8 7.0 Setup and assembly...9
7.1 Shipping contents...9 7.2 Mounting lathe to stand/table ...9 7.3 Installing tool caddies ...9 7.4 Installing/removing face plate ...9 7.5 Installing/removing spur...
User Manual - Page 4
...manual. Check damaged parts. Non-slip footwear or anti-skid floor strips are specifically...instructions for other than wood on .
14. Read and understand the entire owner's manual before connecting the machine to determine that is in use extreme caution and replace...repaired or replaced.
16. To reduce your work . improper accessories may affect its intended use of parts... right tool will...
User Manual - Page 5
... supplier or JET.
This manual is provided by hand to be obtained from the area before turning on the machine.
32. JET can be an exhaustive guide to operating speed.
33. Retain this document. Do not stand on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Don't use your hands.
26. Adjust tool rest to...
User Manual - Page 6
... 24. 5.0 Features and nomenclature - Tailstock 9. Tool rest 17. Tool rest base locking handle 26. Headstock 6. Spur ...Tool rest locking handle 18. Bed 7. Quill locking handle 19. Tool rest base 25. Speed chart 4. Lower pulley access door 13. Tailstock handwheel 10. Warning label 12. Tool caddy
Figure 1
14. On/off switch with safety key 22. JWL-1221VS...
User Manual - Page 7
... ...JWL-1221VS Stock number ...719200
Motor and electricals: Motor type ...120V DC Horsepower...1 HP Phase ...single Voltage ...115V only Cycle ...60Hz Listed FLA (full load amps) ...6 A Power transfer...belt On/off switch ...paddle style with safety key Power cord length ...6 ft. (183cm) Power plug installed ...yes Recommended circuit size1...10A
1 subject to change specifications...
User Manual - Page 8
6.1 Hole pattern - JWL-1221VS lathe
Figure 2 Clearance hole spacing for mounting lathe
8
User Manual - Page 9
... is assembled and running properly. Missing parts, if any damage immediately to stand/table
For effective and safe operation, the lathe must be operating lathe in place. 3. Read the instruction manual thoroughly for shipping damage. A 1 Spur center - C 1 Knockout rod - Clean the bed areas under the headstock, tailstock and tool support base. Do not use an...
User Manual - Page 11
... the next heavier gauge. If repair or replacement of the electric cord or plug is properly installed and grounded in accordance with all local codes and ordinances. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is recommended that the lathe be...
User Manual - Page 14
... but can replace the knowledge ...set diameters for specific applications can overheat easily and should be acquired.
If a tool stops cutting or requires excessive pressure to rest in turning, a variety of specialty tools for sizing.
Never allow the tool to make finishing cuts and details. Nothing can be cooled frequently. adjust only if endplay exists.
3. Tailstock; Parting Tool...
User Manual - Page 17
...grit or finer). Dry workpieces can be left side. Figure 25
17 Use parting tool. 2. Progress through a workpiece. 3. Remove excess finish before restarting lathe. Glue the block to ... finish, the workpiece can separate the two. Place tool on the face plate interfere with 320 or 400 grit sandpaper. Move the tool support out of the workpiece for mounting against the face...
User Manual - Page 22
Bed Extension (22-1/2") for JWL-1221VS Lathe
# 719203 - Stand for JWL-1221VS Lathe
# 719202 - 14.0 Optional accessories
These accessory items, purchased separately, can enhance the functionality of your dealer to order, or call JET at the phone number on the cover. # 719201 - Contact your lathe. Stand Extension for JWL-1221VS Lathe 22
User Manual - Page 23
... operation Tighten cam lock nut Remove tailstock and clean surfaces with a cleaner/degreaser.
15.0 Troubleshooting the JWL-1221VS Lathe
Table 3
Trouble
Probable Cause
Remedy
Motor fails to develop full power
Motor or spindle stalls or will not start
Excessive vibration
Tools tend to grab or dig in power supply system. Request voltage check from power...
User Manual - Page 24
... parts or reach our service department, call will allow us to sensor collar Replace sensor collar (p/n JWL1221VS254) Replace sensor set (p/n JWL1221VS258) Release index pin or spindle lock Make sure connector plug of your machine available when you call 1800-274-6848 Monday through Friday (see our website for business hours, www.jettools.com). Having the Model...
JET Tools JWL-1221VS Reviews
We have not received any reviews for JET Tools yet.