ZyXEL XS3800-28 Support and Manuals
Get Help and Manuals for this ZyXEL item
View All Support Options Below
Free ZyXEL XS3800-28 manuals!
Problems with ZyXEL XS3800-28?
Ask a Question
Free ZyXEL XS3800-28 manuals!
Problems with ZyXEL XS3800-28?
Ask a Question
Popular ZyXEL XS3800-28 Manual Pages
User Guide - Page 23
...Application
1.1.1 Multi-Gigabit
A 10 Gigabit port supports speeds of writing, most existing cabling is Cat 5e or Cat 6, further limiting maximum speed/distance potential. XS3800-28 User's Guide
23 If a network device such as a...Gigabit ports. it drops to 1G if these problems by additionally supporting 2.5 Gigabit and 5 Gigabit Ethernet connections over Cat 5e and higher Ethernet cables. Multi-...
User Guide - Page 47
... Versions
If you want to check the supported models and firmware versions later, you will see the device release notes for ZON utility support. If your device is not listed here, see if your device and firmware version support the ZON
Utility. Then select the Supported model and firmware version link. XS3800-28 User's Guide
47 Chapter 4 The Web Configurator • 100MB...
User Guide - Page 49
... and unzipped it 'll show in advance.
You must have downloaded the firmware from the Zyxel website to enable or disable the Nebula Control Center (NCC) discovery feature on the connected network again.
XS3800-28 User's Guide
49 You must know the current admin password before changing to selected device(s) of the selected AP. Use this...
User Guide - Page 84
... be connected.
Figure 58 Basic Setting > General Setup
XS3800-28 User's Guide
84 otherwise Error is currently operating from the power source. Status
Active indicates the Switch is displayed.
Current
This is functioning above the minimum speed. Chapter 8 Basic Setting
Table 14 Basic Setting > System Info > Hardware Monitor (Stacking Mode) (continued)
LABEL
DESCRIPTION
Status...
User Guide - Page 101
... this screen to a screen where you can configure the IPv6 neighbor discovery settings. Figure 71 Basic Setting > IPv6 > IPv6 Configuration > IPv6 Global Setup
XS3800-28 User's Guide
101
IPv6 Neighbor Setup
Click the link to go to configure the global IPv6 settings. IPv6 Global Address Setup
Click the link to go to a screen where you can create a static IPv6...
User Guide - Page 106
... table describes the labels in IPv6 router advertisements, which means IPv6 hosts use DHCPv6 to obtain additional configuration settings, such as a default router for this screen afresh. Table 31 Basic Setting > IPv6 > IPv6 Configuration > IPv6 Router Discovery Setup
LABEL
DESCRIPTION
Interface
Select the IPv6 interface you want to change the settings. XS3800-28 User's Guide
106
User Guide - Page 108
...change the settings.
Click Cancel to begin configuring this to create a new entry or to update an existing one. Click Clear to reset the fields to select a specific entry. ... screen to display the screen as shown next. Figure 78 Basic Setting > IPv6 > IPv6 Configuration > IPv6 Neighbor Setup
XS3800-28 User's Guide
108
This is the interface index number.
Click this screen afresh....
User Guide - Page 115
... the Switch defined. 6 The second Switch master LED will then turn on the port settings. Figure 84 Basic Setting > Stacking > Configuration
XS3800-28 User's Guide
115 Please wait
until it stops blinking, indicating that it 's initializing. Chapter 8 Basic Setting 1 Select a Switch to support the stacking mode. See Section 8.5 on page 94 and Section 9.7 on page 117 for details on...
User Guide - Page 168
... Cancel to the same region.
The Switch supports instance numbers 0-16. Set the priority of the VLAN ID range that...are mapped to the MST instance. • Clear - XS3800-28 User's Guide
168 This is aged. Enter a descriptive name (up...stacking mode. Active
Select this section to identify a region's configuration. Enter a number to configure MSTI (Multiple Spanning Tree Instance) settings...
User Guide - Page 272
...media server, S, via the Switch. XS3800-28 User's Guide
272 Multiple subscriber devices can set your Switch to operate in the forwarding...on the Switch). This allows the multicast devices to update the multicast forwarding table to forward or not forward multicast... receiver port (in this case, you must manually configure the forwarding settings on the Switch that matches the multicast stream to...
User Guide - Page 283
... screen afresh.
26.2.2 TACACS+ Server Setup
Use this screen to configure your network administrator instructs you are done configuring. See Section 26.1.2 on page 280 for more information on the top navigation panel to save your RADIUS accounting server settings.
Figure 215 Advanced Application > AAA > TACACS+ Server Setup
XS3800-28 User's Guide
283
This key is a read...
User Guide - Page 378
... for troubleshooting. In stacking mode, the first number represents the slot and
the second the port number. The Zyxel Switch device...supported.
The Link Aggregation TLV indicates whether the link is capable of the port.
• Aggregation Status -
The current aggregation capability of being aggregated, whether the link is :
• Network Connectivity
XS3800-28 User's Guide...
User Guide - Page 383
... Power Pairs • Power Class
This displays the maximum supported frame size in an aggregation, the port identification of remote Switch which indicates whether the VLAN ID and whether it advertises whether these setting were the result of the sending 802.3 node. XS3800-28 User's Guide
383
The auto-negotiation capabilities of the port.
•...
User Guide - Page 405
...causing STP topology changes in the network. Click Advanced Application > BPDU Guard in the Basic Setting > Port Setup screen (Section 8.5 on page 94) or use the Errdisable Recovery screen (see Section 33.6... on the port(s) on the Switch and the port status. XS3800-28 User's Guide
405 You can then enable the port(s) manually in the navigation panel. The BPDU guard feature allows you to...
User Guide - Page 409
... troubleshoot network connection problems. The Switch supports the following IEEE 802.3ah features: • Discovery - Because link layer Ethernet OAM operates at layer two of the OSI (Open Systems Interconnection Basic Reference) model, neither IP or SNMP are necessary to view the configuration of the Ethernet link and their OAM configuration. • Remote Loopback -
XS3800-28...
ZyXEL XS3800-28 Reviews
We have not received any reviews for ZyXEL yet.