3Com 3C8S5907 - PathBuilder S590 Bridge/router Support and Manuals
Get Help and Manuals for this 3Com item
This item is in your list!
View All Support Options Below
Free 3Com 3C8S5907 manuals!
Problems with 3Com 3C8S5907?
Ask a Question
Free 3Com 3C8S5907 manuals!
Problems with 3Com 3C8S5907?
Ask a Question
Popular 3Com 3C8S5907 Manual Pages
User Guide - Page 3
... happens the telephone company will provide advance notice in the "Technical Support" section of a certified connector assembly. In some cases, the inside wiring associated with the instruction manual, may make necessary modifications to Identify and Resolve Radio-TV Interference Problems
This booklet is operated in some situations. If this device...
User Guide - Page 42
...set. Values include numerics, strings, or addresses depending on ports, paths, or commands, see Reference for Enterprise OS Software. In some cases, you want the parameter to be executed successfully. The value part...interface.
If your command requires more modification, continue to step 3.
The service part of the command focuses the action of the command on as root or as ...
User Guide - Page 58
...setup using :
SETDefault ! -PAth ConnControl = Enabled
Connector parameter settings are supported. Use SH7 for E1 connectors. For T1 lines, long haul and short haul settings are not applied until the connector is supported...LH1|LH2|LH3|LH4|SH1|SH2| SH3|SH4|SH5|SH7
The LineDistance parameter determines the supported long haul (LH) or short haul (SH) line distance. 58 CHAPTER 4: BASIC ...
User Guide - Page 59
...fies the transmission encoding method for single path, unstructured service. For T1 lines both long haul and short haul settings are the following:
T1_SF T1_ESF E1_CRC4 E1_NOCRC
Superframe format T1.
E1 without an active CRC.
2 Set the connector type as appropriate for your setup using:
SETDefault ! -PAth CONNector = E1_Unstructured |T1_Unstructured
where = 4A, 4B...
User Guide - Page 61
... your setup using :
SETDefault ! -PAth ConnControl = Enabled
Connector parameter settings are not applied until the connector is enabled. The coding method you specify for E1 connectors. AMI or B8ZS should be used for T1 connectors and HDB3 should be used for the serial line must match the attached communication device. Further granularity is supported...
User Guide - Page 62
...T3E3FrmMode = E3
For more information about the Path Service parameters and settings, see the Path Service parameters chapter in Reference for Enterprise OS Software. Configuring the ATM Interfaces
This section describes...speed T3/E3 ports for E3 operation using:
SETDefault ! -PAth CONNector = BNC
2 Set the T3/E3 frame mode using permanent virtual circuits (PVCs), LAN Emulation (LANE), and ...
User Guide - Page 65
..., ATMLE, Path and Port Service parameters and settings, see the appropriate chapters in Reference for Enterprise OS Software. Where To Go From Here
If you have a leased line, see Using Enterprise OS Software to complete your port and path configuration. s the local and remote user ID and password.
Where To Go From Here...
User Guide - Page 69
...Using Enterprise OS Software). At the central site, follow these steps:
1 Configure the L2Tunnel Service (see the Building Internet Firewalls chapter in Using Enterprise OS Software) to enable the PathBuilder switch as a ... except the configuration required to the central site based on the bridge/router at the remote office.
This method can access the network and forwards...
User Guide - Page 71
...
Status
Alert Pwr
Fwd
OfficeConnect
bridge/router
PPTP or L2TP tunnel
ISP Firewall
or CSU/DSU (optional)
Central site PathBuilder switch
The connection process typically follows...router. 71
At the central site, follow these steps:
1 Configure the L2Tunnel service (see the Configuring L2Tunnel Connections chapter in Using Enterprise OS Software) to enable the PathBuilder switch...
User Guide - Page 73
...profile contents and key as the remote site (see the Configuring L2Tunnel Connections chapter in Using Enterprise OS Software) to enable the PathBuilder switch as a tunnel terminator.
2 Configure the firewall device if present, or the PathBuilder switch... part of the Web Link, the web-based network Monitor management application for monitoring the performance of service ...
User Guide - Page 77
... URL into your Internet browser:
http://www.3com.com/
This service provides access to online support information such as technical documentation and software, as well as support options that you access the 3Com Corporation World Wide Web site. Located on the World Wide Web at http://knowledgebase.3com.com, this service gives all 3Com customers and partners complementary, round-the...
User Guide - Page 78
...the service by modem, set your FTP client: s Hostname: ftp.3com.com s Username: anonymous s Password:
You do not need a user name and password with Web browser software such as Netscape Navigator and Internet Explorer.
3Com Bulletin Board The 3Com BBS contains patches, software, and drivers for 3Com products.
78 APPENDIX B: TECHNICAL SUPPORT
3Com FTP Site Download drivers, patches, software...
User Guide - Page 79
... the following number: 1 847 262 6000
3Com Facts The 3Com Facts automated fax service provides technical articles, Automated Fax diagrams, and troubleshooting instructions on how to provide a variety of system hardware and software, including revision levels s Diagnostic error messages s Details about your support options, call the 3Com technical telephone support phone number at the location...
User Guide - Page 118
... phase. Lights amber if an error in the
frames is up.
Select
Link Active Fault
Normal operation
Link Lights green when the path is detected. Action: Reload the software.
Select Lights green to indicate which interface is active on the module.
118 APPENDIX E: TROUBLESHOOTING
ATM LEDs The following examples and follow the instructions for troubleshooting.
User Guide - Page 189
... 3Com's Corporate Service Center or an Authorized 3Com Service Center within fifteen (15) days after the date of 3Com. In the event a product completely fails to function or exhibits a defect in materials or workmanship within the first forty-eight (48) hours of installation but may be delayed due to export or import procedures. Any replaced or repaired product or part...
3Com 3C8S5907 Reviews
Do you have an experience with the 3Com 3C8S5907 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for 3Com yet.
Earn 750 points for your review!