3Com 3CCFEM556B - Megahertz 10/100 LAN Support and Manuals
Get Help and Manuals for this 3Com item
View All Support Options Below
Free 3Com 3CCFEM556B manuals!
Problems with 3Com 3CCFEM556B?
Ask a Question
Free 3Com 3CCFEM556B manuals!
Problems with 3Com 3CCFEM556B?
Ask a Question
Popular 3Com 3CCFEM556B Manual Pages
User Guide - Page 5
... Windows 98 Support 54 Windows NT Troubleshooting 55 Windows NT 5.0 Support 56 Windows 3.1x Troubleshooting 56 LAN Problems with NDIS2 Drivers 57 LAN Problems With ODI Drivers 58 Basic LAN Troubleshooting 59 Troubleshooting Guidelines 59 LAN Driver Placement in AUTOEXEC.BAT 59 Forcing Full-Duplex Mode 59 Basic Modem Troubleshooting 60
A SPECIFICATIONS
B TECHNICAL SUPPORT
On-line Technical Services...
User Guide - Page 7
... multifunction extensions to a telephone line. 1
INTRODUCTION
The 3Com® Megahertz 10/100 LAN+56K Modem PC Card (called the LAN+Modem card in this multifunction specification.
Figure 1 10/100 LAN+56K Modem PC Card
The LAN+Modem card is a dual-function device. Windows 95® and Windows NT® both support this guide) links your notebook computer to a Fast Ethernet...
User Guide - Page 8
.... See http://www.3com.com/56K for Microsoft® (NDIS2, NDIS3, and NDIS4) and Novell® NetWare® (ODI) networks.
s Windows 95 Plug-and-Play support. s Driver support for details. Supported network management applications can retrieve performance data and error statistics from ISDN or digital PBX lines. 2
CHAPTER 1: INTRODUCTION
Features of the LAN+Modem card include:
s Parallel...
User Guide - Page 9
... not already have. However, before installing the LAN+Modem card, you should know: s What network operating system you will connect to s What information you need to set up a network
connection, for any setup information that you are : 1 Run Setup to view installation instructions.
In some cases, the Setup program will run and what setup
parameters they require
Ask your...
User Guide - Page 13
...) slots. The power to most notebook computers. Inserting the LAN+Modem Card
These general instructions apply to the computer can be on or off. Without forcing the...manual that accompanied your computer for instructions specific to disconnect the connector from the card. To install the card, slide it inoperable. Inserting the LAN+Modem Card 7
When attaching connectors to the LAN+Modem...
User Guide - Page 14
However, if you want to install the help, diagnostic, and support utilities provided for the LAN+Modem card, you are described in Chapter 9. They will light when the network driver is installed and you must run Setup (see "Running Setup" in Chapter 3). Figure 4 Connecting the Twisted-Pair Adapter The LEDs on the LAN+Modem card.
3 Connect one end of...
User Guide - Page 27
... modem adapter and telephone cables as chosen at Step 4 and click OK.
21 Select 3Com Megahertz 10-100 + 56K PC Card (Modem Interface) and click Next.
22 Select a port for the modem ...modem manufacturers and models will appear. In order for the requested fields and click Next.
24 Click Finish to open the Control Panel.
17 Double click Modems to complete the installation. Running Setup ...
User Guide - Page 30
... drive.
2 Click File from Program Manager.
3 Click Run.
4 Enter a:\setup
5 Follow the prompts as described in this Guide. 24
CHAPTER 5: INSTALLATION FOR WINDOWS FOR WORKGROUPS
Running Setup to Install Microsoft Network Clients
During the Setup procedure, you specify a different directory, note the new name. Before using the modem, make sure the communications software you access to your...
User Guide - Page 34
... driver as described in the following sections. See your system administrator or network manuals for installing the LAN+Modem card software. To install your LAN+Modem card under Windows:
1 Insert Installation Disk 1 into any PC Card slot in Chapter 2. The default directory is installed and the cables are connected as described in your notebook. Setup prompts for a directory for installation...
User Guide - Page 35
... ODI client software (including the driver), and to see problems listed in Chapter 2.
2 Boot the PC under DOS.
3 Insert Installation Disk 2 into drive A and type: a:config [Enter]
4 Choose Auto Install and Config for NetWare (AutoLink) and Press [Enter]
5 Select AutoLink Windows 3.x or WFW 3.11. A final message indicates successful installation. To use the AutoLink program...
User Guide - Page 37
... might not work with a range of the network drivers available when 3Com shipped the LAN+Modem card. Locate the Support Welcome screen, Select Network Interface Cards, then select Software/Drivers. In DOS environments, the point enabler (FMENABLE.EXE) must run
a:\config.exe
About Point Enablers and Card Services
In DOS, Windows 3.x, and Windows for computers that contain Card...
User Guide - Page 38
Verify whether Card Services is installed on your computer. If Card Services is installed, one device statement will not support another PC Card in your computer by the LAN+Modem card. If your Card Services documentation for PC and PCMCIA cards. You must use the point enabler to sockets and system resources, including device drivers, utilities, and application programs...
User Guide - Page 39
... enabler should be installed in the CONFIG.SYS file. For example, type this example, the memory setting is using. The CONFIG.SYS file should contain the line:
device=c:\nwclient\fmenable.exe
Alternatively, you can run the configuration manager manually from DOS each time you use the modem by an 8K...
User Guide - Page 54
... menu.
s NDIS driver installation and information.
Follow the instructions provided on Novell NetWare drivers.
48
CHAPTER 9: DIAGNOSTICS AND TROUBLESHOOTING
To run a:\config.exe. To start CONFIG, put Installation Disk 2 in the disk drive and run the diagnostics test: 1 Start CONFIG from any DOS window. Press [F1] for NetWare Driver Installation and Update
(continued)
Description...
User Guide - Page 55
...from the CONFIG main menu to see these topics. s Software Compatibility Information. DEC® Pathworks® MS LAN Manager
Troubleshooting and Support
s Installing NDIS driver for all Windows environments. s CONFIG Program instructions s Changing the NIC configuration and
running diagnostics software. Card Diagnostics Programs 49
Table 2 CONFIG Information Library (continued)
Menu Item...
3Com 3CCFEM556B Reviews
We have not received any reviews for 3Com yet.