Acer XF253QX Support and Manuals
Get Help and Manuals for this Acer Computers item
This item is in your list!
View All Support Options Below
Free Acer XF253QX manuals!
Problems with Acer XF253QX?
Ask a Question
Free Acer XF253QX manuals!
Problems with Acer XF253QX?
Ask a Question
Popular Acer XF253QX Manual Pages
User Manual - Page 2
... include the serial number, model number and purchase information. All correspondence concerning your computer. Other companies' product names or trademarks are used herein for identification purposes only and belong to the contents hereof and specifically disclaims the implied warranties of Acer Incorporated. Acer Incorporated. Acer LCD Monitor User's Guide Original Issue: 07/2020...
User Manual - Page 4
...comfortably
and without distortion.
• After setting the volume level, do not place the...touch dangerous voltage points or short-out parts that the total
Never spill liquid of... heat register, or in a built-in installation unless proper ventilation is provided.
• Never...of power available, consult your hearing, follow these instructions.
• Gradually increase the volume until you ...
User Manual - Page 5
...devices. Using a power outlet that may result in performance, indicating a need
to replace the power cord set .
v
ampere rating of the equipment plugged into a non-grounded power outlet. ... all servicing to service this product.
• Use the product only with the supplied power supply cord set , make sure that the new power cord meets the following the operating
instructions
User Manual - Page 15
The cord set should have the appropriate safety approvals for the country in which the equipment will not be installed.
Please confirm the distribution system in either 100... required.
Plug one end of the power cord to make sure that allows operation in building installation shall provide the circuit breaker rated 120/240 V, 20 A (maximum). No user-adjustment is the correct...
User Manual - Page 19
... install the monitor to your monitor into the power port at the back of the volume control as well as given below: Steps 1. 1-1 Connect HDMI Cable (Only HDMI-input model)
a. Plug the power cords of your computer and your host system, please follow the steps as the equalizer to other settings than the...
User Manual - Page 21
... general reference only. Modes 2. EN-11 Input 4. Actual product specifications may vary. The OSD (on or off From any function page, press to open the OSD. Brightness 3.
For advanced settings, please refer to use (please see the OSD section for adjusting the settings of your preferred functions.
1. You can use the Hot Key...
User Manual - Page 22
Adjusting the Brightness Open the Brightness control and select the brightness setting using the Navi/ OK button. Selecting the Input Open the Input control and select an available input source.
EN-12 When you are done, press the Navi/OK button to exit. When you are done, press the Navi/OK button to go back one level.
User Manual - Page 23
.... Using the Navi/OK button, select Picture from 0 to 100. Use the Navi/OK button to select a menu function, and adjust the settings which you wish to adjust. 3. Note: Sets the degree of the display- blacks will be less black.
The Function page
Open the Function page to adjust the sliding scales...
User Manual - Page 24
... high-resolution images by boosting the pixel density of the original source. Then navigate to
the setting you wish to automatically detect and process HDR signal. ACM: Turn ACM on or off . 9. The default is set to open the OSD. 2. Using the Navi/OK button, select Color from the OSD.
EN-14...
User Manual - Page 25
..., green, blue, yellow, magenta and cyan
saturation. Press the MENU key to select the setting. 4. Use the Navi/OK button to "HDR" automatically. 2.
Gamma mode allows you wish to adjust. ...is warm. Modes: Select your preferred mode. 7. If Color Space is not "HDR", then Modes is set to adjust the luminance tone. Using the Navi/OK button, select Audio from the OSD. Color temperature: ...
User Manual - Page 26
... the Over Drive selection is "OFF", then the user can set
to
either one of VRB is Extreme or Normal, VRB provides a sharper and clearer dynamic picture; the default is Off. • VRB does not support PIP/PBP Mode and HDR Mode. (Selective
models) • When VRB is Extreme or Normal, FreeSync Premium...
User Manual - Page 27
.... 6. If the OSD Lock message remains, please check whether the Navi/OK button is not supported at resolutions below 800 x 600.
9. Aim Point: Show an Aim point on the screen ... 60%, or 80%. 7. Press the MENU key to adjust. 3. Language: Set the OSD menu language. 5. Note: 1. Then navigate to the
setting you wish to open the OSD. 2. Transparency: Select the transparency when using ...
User Manual - Page 28
.../Command Interface, which allows monitor controls to be set at DP1.4. 7. The
options are Normal and Low.
11. Press the MENU key to select the setting. 4.
Using the Navi/OK button, select System...Navi/OK button to open the OSD. 2. DDC/CI: Allows the monitor settings to adjust. 3. Then navigate to
the setting you are using . HDMI Black Level: You can select which DP format ...
User Manual - Page 29
Product information 1. Reset All Settings: Reset all settings to open the OSD. 2.
From any function page, press the key to the factory defaults. EN-19
User Manual - Page 30
...monitor for servicing, please check the troubleshooting list below to see if you can self-diagnose the problem.
(HDMI/DP Mode)
Problems
Current Status LED ON
No Picture
LED OFF LED displays amber color
Abnormal Sound (Only Audio-Input model) (Optional... the host PC is connected.
Check if the volume setup of the host PC is in minimum position and try to raise the volume level. EN-20
Acer XF253QX Reviews
Do you have an experience with the Acer XF253QX that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Acer yet.
Earn 750 points for your review!