BenQ BenQ PU9530 Large Venue Projector Support and Manuals
Get Help and Manuals for this BenQ item
View All Support Options Below
Free BenQ BenQ PU9530 Large Venue Projector manuals!
Problems with BenQ BenQ PU9530 Large Venue Projector?
Ask a Question
Free BenQ BenQ PU9530 Large Venue Projector manuals!
Problems with BenQ BenQ PU9530 Large Venue Projector?
Ask a Question
Popular BenQ BenQ PU9530 Large Venue Projector Manual Pages
User Manual - Page 2
... panel and functions...10 Remote control and functions...11 Remote control operation...12
Setup and operations...13
Setting the remote control batteries...13 Connecting to the projector...13 Projection lens selection and Installation 14
Installing or removing the optional lens 14 Installing the new lens...14 Using the Anti-theft Screw...14 Removing the existing lens...
User Manual - Page 3
...Tips for troubleshooting...59 Image problems...59 Lamp problems...60 Remote control problems...60 Specifications...62 Dimensions...63 Timing chart...64 PC timing...64 3D supported timing...65 RS232 command control...66 Control the projector through a Network 69 Set up the projector for Network 69 Control the projector through a web browser 70 Projector status...70 Alert mail setup...71 Crestron...
User Manual - Page 5
...) as appropriate to have the projector repaired.
5. Excessive operation of lamps beyond the rated lamp life. Allow the projector to cool for replacement.
!!
5 If the projector does become wet, disconnect it ...call BenQ to your sight.
6. UPS
7. Do not place liquids near or on the projector.
The lamp becomes extremely hot during operation. Do not operate the projector lamp...
User Manual - Page 13
... battery compartment.
English
Setup and operations
Setting the remote control batteries
1. Refit the cover by certain high-frequency fluorescent lights, you can connect to the projector with new ones, ...necessary) and install two new AA batteries observing the battery polarities as illustrated.The cover will not be used batteries according to the battery manufacturer's instructions and local...
User Manual - Page 16
... in one of your dealer for this location with the projector
Select this installation
location.
70cm
* To set the projector position: Press MENU and then press ◄/► until the correct position is required to highlight Projector Installation and press ◄/► until INSTALLATION menu is highlighted. Front Ceiling:
4. Press ▲/▼ to dissipate heat...
User Manual - Page 20
... the Security Lock function is displayed.
20 If you have set or changed the password, take a memo and keep it securely. Press arrow keys to the following guide. 1.
Unlocking the projector To unlock the projector, refer to display the Main
menu. Contact your PIN code, the projector can no default keyword; Press Menu on the OSD control...
User Manual - Page 28
... the fans stop and the Power indicator light turns orange.
28 The projected image will be a problem with the start the projector shortly after power has been applied. 2. Refer to the following guide to "Troubleshooting" on page 58. If any of the LEDs remain flashing or blink there may run for use. 5. Press Power...
User Manual - Page 37
... H
Test Pattern
Color Bar, Crosshatch,
Burst, H Ramp, Red, Green,
Blue, White, Black, Off
HDBaseT / Network Auto, HDBaseT
Model Serial Number Software Version BenQ Firmware version Lamp Status Source Information
Usage Time
Filter Timer Reset Factory Reset
BenQ projector xxxxx xxxxx xxxxx xxxxx xx-xxx
Lamp1 Status
Lamp2 Status
Active Source
VGA
Pixel Clock
13.50...
User Manual - Page 43
...option is narrowed. Side by Side: Manually switch the 3D Format to the HDMI input signal, the signal can be enabled for setup by Side, Top/Bottom or Frame ...narrow the horizontal size of the projected image. Reset: Set the H/V Alignment back to the factory default settings.
3D Set up 3D format and sync method.The projector displays options available for the input signal below:
•...
User Manual - Page 58
... WARNING LED.
The internal temperature is high. 99 Placed projector under cooling Start up Normal, Lamp Power is set to Normal Normal, Lamp Power is set to ECO Lamp Power is set to alert users of problems with your nearest authorized dealer or service center.
58
English
Troubleshooting
Indicator messages
Several indicator messages are used by the...
User Manual - Page 59
... take when troubleshooting:The information may be replaced. 99 Install the lamp or check if the lamp is usually
done by pressing an Fn-key combination on . • Ensure all equipment and power up again in suspend mode. • Ensure a connected notebook computer is configured for troubleshooting
In each problem-specific section, try the steps in...
User Manual - Page 60
... serviced. Replace the lamp module. 6. Replace the lamp module. 3. Check the battery polarity. 5. Problem:The image is no contrast 1. To ensure the problem is not caused by testing with no light from the projector 1. Problem:The color of the OSD to turn off any fluorescent lights in the projector and have the projector serviced. Adjust the Color temperature and Picture settings...
User Manual - Page 69
... be manually entered. Gateway: Set up the gateway address in the same way as for Network
Please set to On, the DHCP server of having to increase or decrease the number in the IP address.
192
168
0
100
Subnet Mask: Set up the projector for the IP Address setup.
If the LAN does not support DHCP service, please...
User Manual - Page 71
... up user name for the projector's sending reminder email through SMTP server. : Set up user password. : Enable or disable E-mail Alert function. : Set up sender's email address. : Set up recipient's email address. : Set up CC recipient's email address. : Set up projector name or ID : Set up installation location of a projector error. Make the following settings before enabling this button to...
User Manual - Page 73
...: Display list of who made it.This product supports PJLink control commands. PJLink Security: Select On to enable PJLink security password or Off to disable it .
Control your projector with PJLink commands PJLink is masked. Please set up password for detailed setup steps. Tool: Set up to control projectors with standard commands regardless of signal sources. Press again...
BenQ BenQ PU9530 Large Venue Projector Reviews
We have not received any reviews for BenQ yet.