Bernina 43D Support and Manuals
Get Help and Manuals for this Bernina item
Popular Bernina 43D Manual Pages
Manual - Page 1
INSTRUCTION MANUAL MODEL BERNETTE 43/43D
OFS=CP-5 - 5- 4
CP iii
Manual - Page 2
...Use this manual. Do not operate where aerosol (spray) products are being administered. 8. To unplug, grasp the plug, not the cord. 10....replace bulb with any other user servicing adjustments mentioned in .
To adjust stitch width, turn all moving parts. This overlock machine is required around the overlock machine needle. 11.
Do not use outdoors. 7. See Page 20 for instruction...
Manual - Page 3
... (FOR ROLLED OR NARROW HEM) 17. TRIAL SEWING 7. PROBLEMS AND CAUSES
Page
2 3 4 5 6 8 9 11 12 13 14 15 16 17 18 19 20 21 22 23 24 REPLACING THE CUTTING BLADE 13. SEWING APPLICATIONS 16. BLIND HEMMING 21. CONTENTS
1. PREPARATION FOR THREADING 5. SEWING APPLICATIONS 15. NAMES AND FUNCTION 2. SETTING UP YOUR MACHINE 4. ADJUSTING THREAD TENSIONS 8. DIFFERENTIAL FEED (DF...
Manual - Page 4
... work on blouses, skirts, shirts, slacks, coats and trimming handkerchiefs, towels, tableclothes, and so on the needles when operating the overlock machine. Keep your sewing. * When you temporarily leave the overlook machine. * When replacing any stains on the sewing materials.
2. tions for this instruction manual thoroughly before you intend to sew.
3. Read this portable...
Manual - Page 7
...OFF" position before connecting the cord and before changing needles
or throat plates. This will the machine.
Foot control
0
0
0
Main switch PC:we,' socket
Caution:
1. sew slowly and increase in use .... Disconnect the electrical cord from the wall outlet when mchine is not in speed with added pressure. The power switch is being cleaned. 2. SETTING UP YOUR MACHINE
• Connecting the...
Manual - Page 9
THREADING YOUR MACHINE
Correct threading is colored for threading indication. You will find a threading
illustration when you to have your tension
set on "0". e Raise the needle to have
...foot, knives or the needle plate, and the like.
-6-
0 0
7 In addition, each thread guide is Important otherwise uneven stitches or thread breakage may be found in the thread. Make certain to the ...
Manual - Page 10
... Control and run the machine until the upper and lower thread knots come through the eye of the needles. r
EASY THREAD CHANGING
Instructions for changing threads are given below . Cut the threads and, manually, pass them through the tension discs and behind the hook in each knob to the desired setting numbers according to...
Manual - Page 14
...8226; Spun
polyester • Polyester
Needle
Stitch length
2.0 --3.5m/m Standard 2.5m/m
Recommended tension settings
0 e e 8
Medium weight • Cotton • Poplin • Wool •...Velour • Canvas • Upholstery
• Cotton • Spun
polyester • Polyester
Standard sewing machine needle
Type: HAxl (Japan) or
1301705H (Europe) or
15x1 (USA)
2.0 -3.5m/m
Standard ...
Manual - Page 15
... or the left needle.
Left needle set screw Right needle set screw. Remove the left needle can be removed simply by loosening the needle set screw
Right needle
(3) Back side
(b)... dial(away or toward you sew : (a) 3-thread overedge stitch, 5mm width. ADJUSTING OVERLOCK STITCH WIDTH
This machine Is a two needle, three or four thread convertible overlock machine. Remove the right
needle.
...
Manual - Page 16
... PRESSURE
The presser foot pressure of the machine has been pre-set and requires no particular readjustment according to the type of this machine has been PRE-SET to 3mm.
However, if you need ... fabric (light-or heavyweight).
Loosen
Tighten presser adjusting screw
-13- For sewing very thin fabric, loosen the pressure by turning the screw counter clockwise, and for heavy fabric, tighten...
Manual - Page 17
... remove the needles. GI) Make one complete turn of needle facing away from the power supply before replacing a needle. • Your needle system is cool.
REPLACING THE LIGHT BULB
* CAUTION: Always disconnect your machine from you are sewing. Replace withh a new bulb. () Reset the light cover screw.
-14- Do not attempt to check for the...
Manual - Page 18
... to Its highest position by removing plug from your machine.
-15- The upper blade might become dull after using over a period of time and will need to be replaced, a new one can be replaced. Tighten the upper
blade set screw securely. Loosen the upper blade set screw and take off the upper
Presser foot
Upper...
Manual - Page 22
...plate screw and remove the standard throat plate, replacing with a standard overdge needle throat plate attached to its lowestposition. Replace presser toot. Make a trial
sewing sample and check if any adjustments are possible ...THROAT PLATE (FOR ROLLED OR NARROW HEM)
The machine comes with the
rolled edge throat plate. O Turn the hondwheel toward you and set screw and remove the left needle...
Manual - Page 25
.... The front feed dog, therefore, holds the fabric back so that the
stitches just overcast the folded edge. 3. Adjust the plastic guide so that the rear feed dog can be greater than that of fabric. f
Pinlucking
Sewing in garments made from knits or stretch fabrics. (USE 4--.5 mm WIDTH OF THE TAPE)
Tape...
Manual - Page 27
.... Replace with a new needle. Readjust the cutting space width
Reduce the needle thread tension.
14 9-11
13 9-11
Re-thread the machine correctly.
6-7
Consult your dealer
If above corrective actions do not solve your trouble, contact your dealer. -24-
Thread breakage. Motor problems.
C) Excessive noise. ® The motor will not run. ® Sparks are sewing...
Bernina 43D Reviews
We have not received any reviews for Bernina yet.