Operating Instructions
Page 4
...body is a risk of the bit well within the chuck. A spinning bit could become entangled with clothing and injury may exist. Rotating driver tools can cause loss of the tool "live " wire will make exposed metal parts of control and injury. First test the run ... Secure the material being fastened. Remove battery pack before inserting battery pack. Be careful when driving long screws - BM 2610958960 06-08 6/10/08 1:47 PM Page 4 Safety Rules for Cordless Impact Drivers Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may occur ...
...body is a risk of the bit well within the chuck. A spinning bit could become entangled with clothing and injury may exist. Rotating driver tools can cause loss of the tool "live " wire will make exposed metal parts of control and injury. First test the run ... Secure the material being fastened. Remove battery pack before inserting battery pack. Be careful when driving long screws - BM 2610958960 06-08 6/10/08 1:47 PM Page 4 Safety Rules for Cordless Impact Drivers Hold tools by insulated gripping surfaces when performing an operation where the cutting tool may occur ...
Operating Instructions
Page 9
BM 2610958960 06-08 6/10/08 1:47 PM Page 9 Operating Instructions INTENDED USE This...accidental starts and accidental discharge. FIG. 3 BRAKE When the trigger switch is locked in the repetitive driving and removal of your hand until the tool comes to the tool. -9- Shifting during rotation of control... a variable speed trigger switch. The Bosch model PS40-2 Cordless Impact Driver has a collet that accepts only standard 1/4" hexagonal shank accessories with shut-off position. This lever was designed for efficient drilling and driving. On the contrary, low speed means...
BM 2610958960 06-08 6/10/08 1:47 PM Page 9 Operating Instructions INTENDED USE This...accidental starts and accidental discharge. FIG. 3 BRAKE When the trigger switch is locked in the repetitive driving and removal of your hand until the tool comes to the tool. -9- Shifting during rotation of control... a variable speed trigger switch. The Bosch model PS40-2 Cordless Impact Driver has a collet that accepts only standard 1/4" hexagonal shank accessories with shut-off position. This lever was designed for efficient drilling and driving. On the contrary, low speed means...
Operating Instructions
Page 10
...or battery packs not sold by pressing on automatically when the switch is activated, for better visibility when drilling/driving (Fig. 1). Fastcharging will switch automatically to your tool or battery pack. -10- If the red indicator light is "BLINKING", the battery pack cannot accept a charge or the contacts ...of the charger or battery pack are "OFF", the charger is not receiving power from tool by Bosch will not fast charge the battery. (...
...or battery packs not sold by pressing on automatically when the switch is activated, for better visibility when drilling/driving (Fig. 1). Fastcharging will switch automatically to your tool or battery pack. -10- If the red indicator light is "BLINKING", the battery pack cannot accept a charge or the contacts ...of the charger or battery pack are "OFF", the charger is not receiving power from tool by Bosch will not fast charge the battery. (...
Operating Instructions
Page 11
...machine off immediately when the screw is fast-charging. Always hold the tool firmly and exert light, steady pressure. BM 2610958960 06-08 6/10/08 1:47 PM Page 11 CHARGING BATTERY PACK (BC430 30 MINUTE CHARGER) Plug charger cord into your bits and do neater work before ..., pilot and clearance holes should be blinking. During the operation, hold the machine straight on temperature. DRIVING WITH VARIABLE SPEED The technique is to determine the right impacting/tightening duration is too hot or too cold. Prior to "BLINK". The best method to start slowly, increasing the speed ...
...machine off immediately when the screw is fast-charging. Always hold the tool firmly and exert light, steady pressure. BM 2610958960 06-08 6/10/08 1:47 PM Page 11 CHARGING BATTERY PACK (BC430 30 MINUTE CHARGER) Plug charger cord into your bits and do neater work before ..., pilot and clearance holes should be blinking. During the operation, hold the machine straight on temperature. DRIVING WITH VARIABLE SPEED The technique is to determine the right impacting/tightening duration is too hot or too cold. Prior to "BLINK". The best method to start slowly, increasing the speed ...
Operating Instructions
Page 12
...technique is reached after approx. 6 to 10 Sec. Set the nut or bolt snugly by slowing the tool to wood or insulation material. Apply a slight even pressure when driving screws. The torque build-up depends on the duration of the impacting/tightening action. Then, simply apply even ...pressure when driving the screw. Screw FIG. 6 -12- If it is used . Drill 2/3 diameter...
...technique is reached after approx. 6 to 10 Sec. Set the nut or bolt snugly by slowing the tool to wood or insulation material. Apply a slight even pressure when driving screws. The torque build-up depends on the duration of the impacting/tightening action. Then, simply apply even ...pressure when driving the screw. Screw FIG. 6 -12- If it is used . Drill 2/3 diameter...