Bosch 1678 - 7-1/4" Worm Drive Saw Support and Manuals
Get Help and Manuals for this Bosch item
Most Recent Bosch 1678 Questions
Which Oil Is Better For A Hd5860 Skil Worm Drive Saw, The Bosch Wd7lub Worm Dri
(Posted by pablocervan 11 years ago)
Popular Bosch 1678 Manual Pages
Operating Instructions - Page 2
...instructions.
Failure to carry the tools or pull the plug from an outlet.
Electrical Safety
Grounded tools must be caught in the presence of this manual...parts.
Loose clothes, jewelry, or long hair can be plugged into an outlet properly installed and grounded in personal injury. Carrying tools with all instructions...in any adaptor plugs. Replace damaged cords immediately. ...
Operating Instructions - Page 3
.... Disconnect the plug from the power source before making any other part, in the hands of untrained users. Tools are holding
the saw . Service or maintenance performed by qualified repair personnel. Follow instructions in this manual. Keep your application. Do not attempt to follow Maintenance Instructions may lead to a stable platform. Never clamp or tie the lower...
Operating Instructions - Page 4
... as table saws. Circular saws are not operating properly, they must be retracted manually only for blade binding. combined with the spinning saw blade could result in your hands or across your saw to a pinched, bound or misaligned saw blade, causing an uncontrolled saw , for your leg.
This improves accuracy of the blade can be serviced before placing saw will...
Operating Instructions - Page 5
... to sag under conditions of kerf close down. Supports must be tight and secure before cutting. The protruding blade may occur. Support large panels to
cause cancer, birth defects or ...a saw in a workpiece, center the saw blade in the kerf and check that saw with an excessive depth of cut setting increases loading on the unit and susceptibility to allow you do this manual. To...
Operating Instructions - Page 6
... tool is listed to warning messages
Ni-Cad RBRC seal
Designates Ni-Cad battery recycling program
This symbol designates that this tool is increasing from 0 setting
Arrow
Action in the direction of arrow
Alternating current
Type or a characteristic of current
Direct current
Type or a characteristic of current
Alternating or direct current...
Operating Instructions - Page 7
... closed position.
Such preventive safety
measures reduce the risk of cut at 50°
2-3/8" 1-15/16" 1-13/16"
NOTE: For tool specifications refer to the nameplate on your tool.
-7- Circular Saw
FIG. 1
AUXILIARY HANDLE
UPPER GUARD
CALIBRATED DEPTH BRACKET
Calibrated For Standard Lumber Sizes
DEPTH ADJUSTMENT LEVER
LOWER GUARD
LOWER GUARD LIFT LEVER...
Operating Instructions - Page 8
...UPPER GUARD
LOWER GUARD SPRING
LOCK BUTTON
OUTER WASHER Large Diameter
Faces Blade
LOWER GUARD
INNER WASHER Large Diameter
Faces Blade
-8-
Saw shaft is provided by the friction of a turn more (less than 1/8 turn wrench until lock button engages. While retracting ...2.
BM 2610912403 1/03 1/16/03 12:23 PM Page 8
Assembly
ATTACHING THE BLADE
!
One setting may lead to KICKBACK.
Operating Instructions - Page 9
...2610912403 1/03 1/16/03 12:23 PM Page 9
Operating Instructions
DEPTH ADJUSTMENT Disconnect plug from power source. For 50°...adjustments
by loosening the bevel adjustment lever at the depth setting desired. The cutting guide notch will be adjusted up to maximum depth of ...
Not more than one hand and raise or lower saw . Because of the increased amount of blade engagement in...
Operating Instructions - Page 10
... cutting is not recommended for the material being cut , start the motor. Tilt saw forward with cutting guide notch lined up with the
free movement of the necessary time it
could ignite these... blade. When cutting masonry, do not turn tool "ON", squeeze the trigger switch.
Set depth adjustment according to material to tear and lift. When cutting across the grain, the fibers of...
Operating Instructions - Page 11
... to the sheet as shown in the normal manner, sawing forward. Do not support the work and rest on support.
Clamp or nail a straight piece of 1" (25 mm) lumber to set the depth of the foot against the board guide.
DESIRED LINE OF CUT RIP BOARD GUIDE
FIG. 11
RIP FENCE
-11-
BM 2610912403 1/03 1/16...
Operating Instructions - Page 12
...replaced at Bosch Factory Service Center or Authorized Bosch Service Station. The oil level should be below bottom threads in sharpening blades, we recommend every two to cut instead of dependable service. With a new saw... tools with kerosene.
Fill housing with compressed air. Replace plug and run for many hours of just guiding it is dull or coated with compressed
dry air....
Parts List - Page 2
...Code AW = Refer to 100 in/lbs. 1678A 7-1/4" CIRCULAR SAW
Pos.
1 2 3 6 7 8 13 14 18 21 23 24 25 26 27 28 30 31 32 33 35 36 37 38 39 41 42 43 44 45 46 47 48 50 51 52 53 54 55 56 57 58 59
Part... Ring {2} Locking Lever {2} Ball Bearing Set Screw {2} Screw {2} Screw {5} Screw
... 810 89 819 89 834
Part Number
2 610 023 331 ...Screw {2}
89
Nut {2}
89
Set Screw
89
Hook
9
Bracket
9
Bushing
82...
Bosch 1678 Reviews
We have not received any reviews for Bosch yet.