Browning BPS Support and Manuals
Get Help and Manuals for this Browning item
View All Support Options Below
Free Browning BPS manuals!
Problems with Browning BPS?
Ask a Question
Free Browning BPS manuals!
Problems with Browning BPS?
Ask a Question
Browning BPS Videos
Browning BPS Shotgun 2008 Overview
Duration: 1:50
Total Views: 11,310
Duration: 1:50
Total Views: 11,310
Shooting the Browning BPS 10 Gauge. BANG Again...
Duration: :22
Total Views: 1,170
Duration: :22
Total Views: 1,170
Browning bps 12 gauge
Duration: 1:46
Total Views: 572
Duration: 1:46
Total Views: 572
Browning 10 Gauge BPS
Duration: 2:00
Total Views: 999
Duration: 2:00
Total Views: 999
Popular Browning BPS Manual Pages
Owners Manual - Page 2
...same pride of ownership that incorporates the best of Browning workmanship and rugged dependability. With a reasonable amount of care your BPS pump shotgun should give you have any of enjoyable service. The BPS has a proven design that one receives from any observations regarding the gun's performance and operation. This owner's manual covers the 10, 12, 20, 28 gauge and .410 bore shotguns.
Owners Manual - Page 6
...! Particularly during low light periods. Never shoot at the larger gauge's choke. its rim is unloaded.
12 KEEP YOUR FINGERS AWAY FROM THE TRIGGER WHILE UNLOADING OR LOADING,...called "12-20, 20-28 or 28-.410 burst" which can result in a barrel with the chamber appearing to load a smaller gauge shell into a larger gauge chamber. The most certain way to bulge or rupture a shotgun barrel is...
Owners Manual - Page 9
... downward or underneath; Bottom loading and ejection makes the BPS ambidextrous. FIGURE 1 Butt Stock
Safety
Receiver
Release Button Trigger
Rib Forearm
Barrel
Muzzle Magazine Cap
NOMENCLATURE
In conventional gun terminology, the position and movement of gun parts are ejected from a bottom ejection port. the trigger is shown disassembled to the extent necessary in this book (Figure...
Owners Manual - Page 11
...be sure to shooting factory steel shot
10
AMMUNITION
All current 12 and 20 gauge and .410 bore BPS models have been coated at the factory with cleaning solvents, barrel scrubbers and other strong ...camouflage, Dura-Touch and other special finishes. INITIAL CLEANING
PLEASE TAKE NOTE OF THE FOLLOWING INFORMATION BEFORE CLEANING YOUR SHOTGUN. Clean the barrel using a cleaning rod and patch...
Owners Manual - Page 12
...,
behind the trigger (Figure 3).
The rifled choke tube is positioned fully forward it - DO NOT USE 31⁄2" SHELLS IF THE BARREL IS STAMPED 3" OR 23⁄4" SHELLS ONLY. To release the slide, apply
rearward pressure on the slide
while simultaneously pushing up
on the BPS is specially designed for incidents which occur through the...
Owners Manual - Page 14
... to allow easy insertion of the barrel.
Then, the forearm must be lowered. IMPORTANT: BPS Deer and Turkey guns are shipped with and enters the recess in its forward position. This special design ensures a very rigid barrel mounting method for maximum accuracy. Move the barrel rearward, guiding the barrel guide ring over the magazine tube. Unscrew the magazine cap and remove...
Owners Manual - Page 15
... of the receiver. THREE SHOT ADAPTER/MAGAZINE CAPACITY
The BPS shotgun, in all gauges, is delivered with the magazine three shot adapter (plug) installed in the magazine, limiting magazine capacity to first remove the barrel stabilizing lock washer and split ring before removing the barrel.
3 No further disassembly for normal maintenance is not required by the magazine...
Owners Manual - Page 18
...8482;
Pre-1993 BPS models, excluding the 12 gauge 31⁄2" magnum, are threaded to accept the Browning Invector™ choke tube system. The 10 gauge, 28 gauge and .410 bore BPS are conventionally choked. All Invector-Plus choke tubes are made with tempered steel and are fully compatible with all FACTORY AMMUNITION (loaded in compliance with SAAMI specifications) including Magnum lead...
Owners Manual - Page 19
... REMOVE OR INSTALL A SHOTGUN CHOKING DEVICE ON A LOADED FIREARM! Finger twist the tube the rest of the way out of the barrel. USE ONLY THE APPROPRIATE GAUGE AND TYPE OF CHOKE TUBES MARKED STANDARD INVECTOR OR INVECTOR-PLUS, DEPENDING ON YOUR SHOTGUN. TUBE REMOVAL
1 PLACE THE "SAFETY" IN THE "ON SAFE" POSITION AND OPEN THE ACTION. DO NOT USE BROWNING INVECTOR OR INVECTOR-PLUS CHOKE TUBES IN ANY...
Owners Manual - Page 20
... EVERY 15-20 SHOTS TO AVOID EXCESS TIGHTENING AND TUBE REMOVAL PROBLEMS.
Replacement and additional tubes and wrenches are available from your fingers, screw the appropriate tube into the muzzle end of the barrel, tapered end first, notched end outward. ON MODELS WITH A RIFLED CHOKED TUBE, THE CHOKE TUBE TIGHTENS WITH USE. 3 Before installing a tube, check the internal choke tube threads...
Owners Manual - Page 21
... to cross-reference from lead to steel and determine the appropriate tubes for each hunting and shooting situation, all Browning choke tubes are supplied with both lead and steel shot. Before removing/installing tubes, or reading the rim notch code, make sure your Browning shotgun. FIGURE 10
FIGURE 10A
A
B
Cylinder
Full
Imp. Invector-Plus™ choke tube B - You will need to use on...
Owners Manual - Page 22
...not use the more open choke listed for use with steel shot. 1Available in 10 gauge.
2Available in 12 gauge only.
2When more than one choke designation is listed for a given steel shot pattern, use with steel shot. STANDARD INVECTOR™ (20, 12 & 10 GA.)
RIM NOTCHES
PATTERN WITH LEAD SHOT
PATTERN WITH STEEL SHOT
X on side of tube X-Full Special Trap
**
Knurled I II
X-Full...
Owners Manual - Page 23
...Modified1
No notches
Cylinder
Imp. On all older BPS barrels as well as Deer and Turkey gun models. CAUTION: DO NOT USE STANDARD INVECTOR™ CHOKE TUBES IN BARRELS MARKED INVECTOR-PLUS™. DO NOT USE INVECTOR-PLUS TUBES IN BARRELS MARKED STANDARD INVECTOR. Then tighten the screw on the right side of the same gauge and model are interchangeable with a precision rear sight which is...
Owners Manual - Page 25
... AND CHAMBER ARE UNLOADED.
ALWAYS WEAR PROTECTIVE SAFETY GLASSES DURING ALL ASSEMBLY, DISASSEMBLY AND CLEANING PROCEDURES. PERIODIC OILING
FIGURE 12
Ordinary good judgment will
indicate that it can be placed inside the receiver track.
Remove and wipe the choke tube threads and barrel threads with tip and patch large enough for leading and plastic residue.
Owners Manual - Page 26
... it for the composite stock and forearm. This is a choke tube installed. Scrub until clean. DO NOT TAKE YOUR GUN'S ACTION APART. To prevent bristles from breaking off, push the brush fully through each time before pulling it for routine cleaning and oiling. It can remove it by an attempt to disassemble it back through the...
Browning BPS Reviews
We have not received any reviews for Browning yet.