Campbell Scientific CR200X Support and Manuals
Get Help and Manuals for this Campbell Scientific item
This item is in your list!
View All Support Options Below
Free Campbell Scientific CR200X manuals!
Problems with Campbell Scientific CR200X?
Ask a Question
Free Campbell Scientific CR200X manuals!
Problems with Campbell Scientific CR200X?
Ask a Question
Popular Campbell Scientific CR200X Manual Pages
CR200/CR200X-series Dataloggers - Page 13
...datalogger with the CR200(X) manual is available in the manual written for Campbell Scientific products are available on-line at support@campbellsci.com.
1.1
CR200(X) series Datalogger Models
Models CR200X and CR200 Dataloggers do not have a built-in -depth study requires other Campbell Scientific publications are defined by spending a few minutes working through a first attempt at data...
CR200/CR200X-series Dataloggers - Page 42
... Short Cut, then edit the code with DevConfig Software (DevConfig (p. 59)) or through the program Send button in four easy steps.
When the OS is created on a PC and sent to the CR200(X) with DevConfig or through datalogger support software (see Support Software (p. 143)). See Memory and Data Storage (p. 129). Campbell Scientific has increased the data storage memory from 128 kbytes...
CR200/CR200X-series Dataloggers - Page 46
...8226; PC400 supports a variety of data are available. Software for configuring, trouble-shooting, and managing datalogger networks. Overview
Table 3.
For more demanding applications.
34 It includes Short Cut and CRBASIC Editor for creating programs. It also includes tools for datalogger setup and simple applications, PC200W and Short Cut, are available from Campbell Scientific.
•...
CR200/CR200X-series Dataloggers - Page 71
... as part of the serial ports (COM1, COM2, etc.) installed on the application. It is shipped factory ready with all settings and firmware necessary to communicate with DevConfig. The file can be shown, printed or saved to communicate with a PC via direct RS-232 only.
• Sends operating systems to supported device types.
• Sets datalogger clocks...
CR200/CR200X-series Dataloggers - Page 117
... be used in these instructions is set. Enter one of 0.01 seconds. If 0 is used, then the default timeout defined by the time of error codes.
Section 10. CRBASIC Programming Instructions
10.8 Serial Input / Output
Print Sends the values from program variables or other PakBus® devices.
Also see Campbell Scientific PakBus® Networking Guide available at www...
CR200/CR200X-series Dataloggers - Page 120
... radio telemetry or calculation of evapotranspiration and is not CE compliant. CRBASIC instructions used by the CR295(X) are:
GOESData Sends data to satellite transmitter manuals available at www.campbellsci.com.
10.12.1 GOES
The CR295 and CR295X dataloggers support communication through Campbell Scientific's TX312 or HDR GOES satellite transmitters.
Syntax GOESSetup (ResultCode, PlatformID...
CR200/CR200X-series Dataloggers - Page 128
... be used. A green "Active" indicator
116 They are received.
Programming Resource Library
logger issues aD1!, aD2!, etc., until all data are read directly with the sensor address.
11.4.2 SDI-12 Communications
The CR200(X) supports SDI-12 communication through Campbell Scientific datalogger support software, but may need to continuously monitor the measured phenomena, such as Windows...
CR200/CR200X-series Dataloggers - Page 144
... link (Telecommunications and Data Retrieval (p. 131)).
13.4.1 Via Telecommunications
Data are usually transferred through a telecommunications link to send programs, set clocks, collect data, etc. ModBus is PakBus (PakBus Overview (p. 133)). Section 13. Because data retrieval is managed by a PC running Campbell Scientific datalogger support software (Support Software p. 143).
CR200/CR200X-series Dataloggers - Page 151
... bits, and parity are effectively multiplexed to get data from serial sensors.
Because Modbus has a set in the Modbus driver of communications inactivity. Modbus to Campbell Scientific Equivalents (p. 139) lists terminology equivalents to Campbell Scientific Equivalents
Modbus Domain
Data Form
Campbell Scientific Domain
Coils
Single Bit
Ports, Flags, Boolean Variables
Digital...
CR200/CR200X-series Dataloggers - Page 154
... byte order words (CDAB vs. While other CRBasic dataloggers, such as the CR1000, can be true for either the master has to output reverse byte order words, the CR200(X) does not have that supports the MoveBytes() instruction.
15.1.4 Troubleshooting
Test Modbus functions on the CR200(X) with third party Modbus software. ABCD). If reverse byte order words are...
CR200/CR200X-series Dataloggers - Page 163
.... Troubleshooting
Note If any scan skips repeatedly, optimization of the datalogger program or reduction of online processing may be acceptable but should be much higher than actual. The error occurs because counts from a scan and subsequent skipped scans are caused by long programs with pulse channels. Read More! Status Table and Settings p. 15 for repair...
CR200/CR200X-series Dataloggers - Page 164
...Contact a Campbell Scientific applications engineer to a value of the compile results in CRBASIC Editor. Because CR200(X) programs are compiled externally by the compiler are found before the program reaches the CR200(X). These errors are found may occur. Table 24. Compiler executable version is checked for data tables and variables. By default, datalogger support software "sends...
CR200/CR200X-series Dataloggers - Page 179
... to do. parameter Used in the datalogger. Glossary
Ohms Law Describes the relationship of intermediate calculations are entered to specify exactly what a given instruction is controlled by Campbell Scientific to voltage.
It has been developed by the program entered in conjunction with CR200(X) program Instructions, parameters are numbers or codes which are true. The results of...
CR200/CR200X-series Dataloggers - Page 191
... Campbell Scientific's Device Configuration Utility (DevConfig) for direct serial connection, or through PakBusGraph for the CR2xx.
Company PakCtrl Command Codes
BMP5 Command Codes
Model Number RF Protocol
Pin Enabled
Indicates that the radio receiver is enabled.
Appendix B. Identifies the manufacturer
Identifies the list of PakBus PakCtrl Interface command codes that the datalogger...
CR200X-Series Specifications - Page 1
...battery is 4 Bs per data point
INTERMEDIATE STORAGE: 8 kB SRAM
COMPILED PROGRAM STORAGE: up to 10 miles with a shorted cell. CR200X-series Datalogger Specifications
Electrical specifications are valid over -40...; contact Campbell Scientific
WARRANTY
Three year covering parts and labor. up to 19.2 kB flash memory depending on structure of 03/02)
CE COMPLIANT DATALOGGERS: CR200X, CR206X,...
Campbell Scientific CR200X Reviews
Do you have an experience with the Campbell Scientific CR200X that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Campbell Scientific yet.
Earn 750 points for your review!