Campbell Scientific TGA200A Support and Manuals
Get Help and Manuals for this Campbell Scientific item
View All Support Options Below
Free Campbell Scientific TGA200A manuals!
Problems with Campbell Scientific TGA200A?
Ask a Question
Free Campbell Scientific TGA200A manuals!
Problems with Campbell Scientific TGA200A?
Ask a Question
Popular Campbell Scientific TGA200A Manual Pages
TGA Series Trace Gas Analzyers - Page 4
Affiliate companies handle repairs for customers within three days of Product Cleanliness and Decontamination" form and comply ...com to the customer at www.campbellsci.com/repair. The following contact information is incomplete, the product will be either emailed to repair@campbellsci.com or faxed to refuse service on the outside of the problem, an RMA number will be returned without...
TGA Series Trace Gas Analzyers - Page 8
...Sample Cell Cleaning 95 8.4 Sample Pumps 95
ii Specifications 28
5.1 Measurement Specifications 28 5.2 Physical Specifications 29 5.3 Power Requirements 29
6. Table of PC Software 39 6.2.2 Updating TGA Operating System 40 6.2.3 Configure Ethernet Connection 42 6.2.4 Set TGA Serial Number and Identification String 45 6.2.5 Run the PC Software 46
6.3 Detailed Setup Instructions 46
7.
TGA Series Trace Gas Analzyers - Page 13
...Specifications 19 5-1. Suggested Naming for TGA Dewars A-2 A-4. Replacement Cables for Gas Names Setting 59 7-3. Dimensions and Part Numbers for EC filters F-5 F-3. Swagelok® cap G-4 H-1. Modules mounted into TGA200A electronics H-3 H-5. TGA Instruction... G-3 G-3. TE-cooled laser assembly installed in a TGA 200A H-1 H-2. Older style two-piece detector holder...
TGA Series Trace Gas Analzyers - Page 17
... tubing
22178
TGA200A SDM Cable, 20ft
15702
Raw Plastic Tubing 1/4 in TABLE 3-1.
Parts Included with the separate items listed in OD X .040 Wall Polyethylene/Alum
18148
10Base-T CAT5 Ethernet Crossover Cable, 25ft
20730
9-Pin Female to facilitate repair or replacement.
• Immediately check package contents against shipping documentation. TGA Series Trace Gas Analyzers...
TGA Series Trace Gas Analzyers - Page 24
..., pn 30723, that contains installation files for TGA TEC Support Software and current TGA firmware used to connect the RS-232 port on the TGA to an RS-232 port on a user-supplied PC. TGA CAT5 Ethernet Crossover Cable 4.1.1.8 Serial Data Cable
A 7.6 m (25 ft) 9-pin female to the analyzer, set settings, and monitor real-time...
TGA Series Trace Gas Analzyers - Page 53
... not interchangeable.
Any TGA100A or a TGA100 with an upgraded CPU module may be used with cables installed
6.2 TGA Software Installation
This manual documents the TGA Windows and TGA TEC software. TGA ...set parameters. These two software packages are very similar, but they are noted as applicable. NOTE
Early DOS-based versions of PC Software
To install the software, run the setup....
TGA Series Trace Gas Analzyers - Page 57
... Device Configuration utility Settings Editor tab
NOTE
The TGA requires a static IP address. Some local area networks are set up to require the... these settings. The MAC address of devices connected to 3000. The IP address, subnet mask, and gateway should be set at the... factory and is stored in nonvolatile memory.
Power down the TGA.
43 The Settings Editor tab ...
TGA Series Trace Gas Analzyers - Page 60
...the TGA has been set for example, with the system.
7.1.1 Startup Procedure
1. Significant changes in Section 7.2, Software User Interface.
6.3 Detailed Setup Instructions
When the TGA is first installed, or if it ...TGA for starting the TGA. A regulator pressure of 0 psig and a flow rate of problems with a new laser) the operational parameters must be cooled automatically.
3. If the TGA ...
TGA Series Trace Gas Analzyers - Page 62
...concentration and concentration noise are consumed, to gauge when to order replacement tanks and to maintain the laser at the set temperature, and the laser heater voltage will be caused by the ... the reference transmittance and compare it to the TGA.
4. A change in the pressure indicates a problem with a TE-cooled laser, record the laser cooler voltage.
6. It can also be determined by...
TGA Series Trace Gas Analzyers - Page 66
... TEcooled lasers, and reports the laser temperature in °C.
7.2.3 Settings Window
The Settings window is shown in K. TGA Series Trace Gas Analyzers
FIGURE 7-5.
TGA Status window without error (left) and with the laser, detectors, calculations, and other ... which allow the user to display and change parameters associated with error (right) and line lock manually disabled.
TGA Series Trace Gas Analzyers - Page 67
...).
If the laser is different for details on the bottom part of damaging the laser. Setting the maximum laser temperature parameter above the LN2 tank temperature....of the window should normally be set and optimized for the individual laser. TGA Series Trace Gas Analyzers
7.2.3.1 Laser CAUTION
FIGURE 7-7. TGA Windows (FIGURE 7-8) supports LN2-cooled lasers that measure temperature ...
TGA Series Trace Gas Analzyers - Page 69
.... Uncheck this limit. The DC, Mod, Zero, and High current parameters may also be set to set the laser current parameters. See Appendix C, Optimizing Laser Parameters, for normal operation. The laser ...The Settings > Laser > Current window is helpful for TGA Windows 55 TE-cooled lasers do not require this limit for the individual laser.
FIGURE 7-10. TGA Windows (FIGURE 7-10) supports ...
TGA Series Trace Gas Analzyers - Page 70
...active, and see Section 7.2.2, Status Window, for TGA TEC Line Lock The Settings > Laser > Line Lock window sets limits used to the center of the line lock function is shown in TABLE ... problem with any of the absorption line cannot be active for normal operation (see Section 7.2.4, Laser Window, for information on the Settings > Laser > Current window and the Laser window. When the error ...
TGA Series Trace Gas Analzyers - Page 145
...TGA model
TGA100 and TGA100A TGA100s and TGA100As have between 70% and 80% absorption. The total flow to give an error ...the gas.
Record the reference transmittance, shown in the Laser Settings window. This increases the path length by adjusting the pressure... than 80%. The reference detector is best to two possible problems.
First, the absorption lines become broader, and absorption in ...
TGA Series Trace Gas Analzyers - Page 147
...The detector electronics have a gain of the setup steps, such as optical alignment. Early TGAs used for use with TE-cooled lasers (see Appendix H.3.1, Basic Upgrade). However, some of 45. The detector..., if the detector signals are cooled to set the offsets and gains manually, adjust one for a specific input module, or if an input module upgrade is an advantage for higher-power lasers, ...
Campbell Scientific TGA200A Reviews
We have not received any reviews for Campbell Scientific yet.