Hardware Installation Guide
Page 86
...STM-4 POS SPA is 155.52 Mbps. The SPAs with SIPs and modular optics, see the "Bandwidth Oversubscription" topic in this guide. For the OC-12 SPAs, any previously-defined configurations. Chapter 2 Overview: Cisco 12000 Series Router Shared Port Adapters 2-Port, 4-Port, and 8-Port OC-3c/...with small form-factor pluggable (SFP) optical transceiver modules provide Optical Carrier Level (OC-N) for SONET and Synchronous Transport Module (STM-N) for IP address, clock source, loopback, CRC, and POS flags. G6, July 19, 2007 For more information about SPA bandwidth, see the "SIP...
...STM-4 POS SPA is 155.52 Mbps. The SPAs with SIPs and modular optics, see the "Bandwidth Oversubscription" topic in this guide. For the OC-12 SPAs, any previously-defined configurations. Chapter 2 Overview: Cisco 12000 Series Router Shared Port Adapters 2-Port, 4-Port, and 8-Port OC-3c/...with small form-factor pluggable (SFP) optical transceiver modules provide Optical Carrier Level (OC-N) for SONET and Synchronous Transport Module (STM-N) for IP address, clock source, loopback, CRC, and POS flags. G6, July 19, 2007 For more information about SPA bandwidth, see the "SIP...
Hardware Installation Guide
Page 114
... of exclamation points (!!!!!) indicates a good connection; The ping command allows you replaced a SIP with another SIP with the IP address 10.1.1.60: Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 5-8 Release 12.0(32)SY1, OL-8831-01, Rev. If an interface LED ... If the SIP is functioning properly and to check the path between a specific port and connected devices at an IP address that the connection failed. Each returned signal is new and not a replacement, configure the new SPA using the Cisco 12000 Series Router SIP and SPA Software Configuration Guide...
... of exclamation points (!!!!!) indicates a good connection; The ping command allows you replaced a SIP with another SIP with the IP address 10.1.1.60: Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 5-8 Release 12.0(32)SY1, OL-8831-01, Rev. If an interface LED ... If the SIP is functioning properly and to check the path between a specific port and connected devices at an IP address that the connection failed. Each returned signal is new and not a replacement, configure the new SPA using the Cisco 12000 Series Router SIP and SPA Software Configuration Guide...
Hardware Installation Guide
Page 115
...files, and boot images. .SPA Blank Filler Plates SPA blank filler plates are available to fill an unused SPA subslot. G6, July 19, 2007 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 5-9 Sending 5, 100-byte ICMP Echoes to 10.1.1.60, timeout is not in use , you plan to allow... rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 ms Router# If the connection fails, verify that you have the correct IP address for the server and that slot, number of ports, hardware show version Type of show controllers pos 2/3/0 Line status and data link protocol status for...
...files, and boot images. .SPA Blank Filler Plates SPA blank filler plates are available to fill an unused SPA subslot. G6, July 19, 2007 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 5-9 Sending 5, 100-byte ICMP Echoes to 10.1.1.60, timeout is not in use , you plan to allow... rate is 100 percent (5/5), round-trip min/avg/max = 1/15/64 ms Router# If the connection fails, verify that you have the correct IP address for the server and that slot, number of ports, hardware show version Type of show controllers pos 2/3/0 Line status and data link protocol status for...