Hardware Installation Guide
Page 146
... indicates that data is always identified as F1 through F/4, depending in slot 0 of VLANs supported by interface type, slot number, a forward slash (/), and the port number. On the Cisco 1751 router and the Cisco 1760 router, the Fast Ethernet interfaces on the slot. Modules and interface cards are... addressed as FastEthernet1 to FastEthernet4, no new or modified commands for the Cisco 1700 Series Routers document. Figure 107 shows the WIC-4ESW interface card. The first port on the features of 16 VLANs. The intrabuilding cable must be shielded and the shield must be referred ...
... indicates that data is always identified as F1 through F/4, depending in slot 0 of VLANs supported by interface type, slot number, a forward slash (/), and the port number. On the Cisco 1751 router and the Cisco 1760 router, the Fast Ethernet interfaces on the slot. Modules and interface cards are... addressed as FastEthernet1 to FastEthernet4, no new or modified commands for the Cisco 1700 Series Routers document. Figure 107 shows the WIC-4ESW interface card. The first port on the features of 16 VLANs. The intrabuilding cable must be shielded and the shield must be referred ...
Hardware Installation Guide
Page 147
... Interface Cards WIC-4ESW Card WIC-4ESW Interface Card Processor Requirements The MPC 860 microprocessor (revision B5 or later) is required for using the Cisco WIC-4ESW card. The following standards are also supported: • 802.1d • 802.1p • 802.1q WIC-4ESW Interface ...Card Platform Limitations The following features are not supported on the WIC-4ESW interface card: • Virtual Local Area Network (VLAN) trunking protocols (server and client modes, and transparent mode v2) • Spanning Tree Protocol (STP) backbone fast • STP portfast Bridge ...
... Interface Cards WIC-4ESW Card WIC-4ESW Interface Card Processor Requirements The MPC 860 microprocessor (revision B5 or later) is required for using the Cisco WIC-4ESW card. The following standards are also supported: • 802.1d • 802.1p • 802.1q WIC-4ESW Interface ...Card Platform Limitations The following features are not supported on the WIC-4ESW interface card: • Virtual Local Area Network (VLAN) trunking protocols (server and client modes, and transparent mode v2) • Spanning Tree Protocol (STP) backbone fast • STP portfast Bridge ...
Hardware Installation Guide
Page 148
... modem, such as a cable modem, or xDSL modem. WIC-1ENET Interface Card LAN Interface Cards • Voice VLANs • General Attribute Registration Protocol (GARP), GARP Multicast Registration Protocol (GMRP), and GARP VLAN Registration Protocol (GVRP) • Cisco Inter-Switch Link (ISL) tagging (the chip does not support ISL) • Layer 3 on-board switching...
... modem, such as a cable modem, or xDSL modem. WIC-1ENET Interface Card LAN Interface Cards • Voice VLANs • General Attribute Registration Protocol (GARP), GARP Multicast Registration Protocol (GMRP), and GARP VLAN Registration Protocol (GVRP) • Cisco Inter-Switch Link (ISL) tagging (the chip does not support ISL) • Layer 3 on-board switching...
Hardware Installation Guide
Page 154
...power, an HWIC must be provisioned with an optional daughter card that distributes inline power. Inline power is routed through the router platform. The Cisco 10/100BASE-T Ethernet switch HWIC provides Layer 2 switching for a detailed description. See the "Stacking of the HWIC. Inline power is used to... provide power to an IP phone or to a wireless access point attached to the ports of Cisco 10/100BASE-T Ethernet Switch HWICs" section on page 7 for traffic between different VLANs on the same HWIC. The daughter card distributes the -48 volt power to a port. Figure 109...
...power, an HWIC must be provisioned with an optional daughter card that distributes inline power. Inline power is routed through the router platform. The Cisco 10/100BASE-T Ethernet switch HWIC provides Layer 2 switching for a detailed description. See the "Stacking of the HWIC. Inline power is used to... provide power to an IP phone or to a wireless access point attached to the ports of Cisco 10/100BASE-T Ethernet Switch HWICs" section on page 7 for traffic between different VLANs on the same HWIC. The daughter card distributes the -48 volt power to a port. Figure 109...