Cisco WS-C3560X-48T-S Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-C3560X-48T-S manuals!
Problems with Cisco WS-C3560X-48T-S?
Ask a Question
Free Cisco WS-C3560X-48T-S manuals!
Problems with Cisco WS-C3560X-48T-S?
Ask a Question
Cisco WS-C3560X-48T-S Videos
Cisco WS-C3560X-48T-S $3750 Price Reduction
Duration: :34
Total Views: 1
Duration: :34
Total Views: 1
How to Reset a Cisco WS-C3560X-48T-L to Default Settings
Duration: 3:01
Total Views: 38
Duration: 3:01
Total Views: 38
How to Reset a Cisco WS-C3560X-48T-E to Default Settings
Duration: 3:01
Total Views: 7
Duration: 3:01
Total Views: 7
How to Reset a Cisco WS-C3560X-48T-S to Default Settings
Duration: 3:01
Total Views: 90
Duration: 3:01
Total Views: 90
Popular Cisco WS-C3560X-48T-S Manual Pages
Command Reference - Page 50
... the QoS domain. In releases earlier than Cisco IOS Release 12.2(20)SE, auto-QoS configures the switch only for 10/100 Ethernet Ports
10 percent... -Queue Map
1
0, 1
Queue Weight (Bandwidth)
81 percent
Priority
2
2, 3, 4, 5, 6, 7
19 percent
1.
You can classify incoming traffic for the egress queues.
These releases support only Cisco IP SoftPhone Version 1.3(3) or later.
Queue...
Command Reference - Page 93
... the cluster members.
78-16405-05
Catalyst 3560 Switch Command Reference
2-61 Switch(config)# cluster member mac-address 00E0.1E00.3333
You can verify your settings by entering the show cluster members
Description Displays the cluster status and a summary of candidate switches. Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
cluster member
Examples
This example shows how...
Command Reference - Page 168
... inspection vlan vlan-range privileged EXEC command. ip arp inspection validate
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
Examples
This example show how to enable source MAC validation:
Switch(config)# ip arp inspection validate src-mac
You can verify your setting by entering the show inventory vlan vlan-range
Description
Displays the configuration and the operating...
Command Reference - Page 216
...
ipv6 mld snooping
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
Examples
This example shows how to globally enable MLD snooping:
Switch(config)# ipv6 mld snooping
This example shows how to optimize system resources based on a VLAN:
Switch(config)# no ipv6 mld snooping vlan 11
You can verify your settings by entering the show ipv6 mld...
Command Reference - Page 258
... a keyword, even if it is part of the keyword are replaced with the corresponding value. There are specific to apply and trace a macro configuration on a switch or to debug the macro to find any required values in the switch software. macro-name
Specify the name of any syntax or configuration errors. All matching occurrences of a larger...
Command Reference - Page 342
... a port that does not support PoE, this command on PoE-capable ports.
power inline {auto [max max-wattage] | never | static [max max-wattage]}
no value is specified, the maximum is configured for a port before the switch discovers the powered device. If you enter this error message appears:
Switch(config)# interface gigabitethernet0/1 Switch(config-if)# power inline auto...
Command Reference - Page 343
...PoE port:
Switch(config)# interface fastethernet0/2 Switch(config-if)# power inline auto
This example shows how to configure a PoE port to allow a Class 1 or a Class 2 powered device:
Switch(config)# interface fastethernet0/2 Switch... requests more than Cisco IOS Release 12.2(20)SE1, power was later connected to the configured speed and duplex settings. If the switch learns through CDP ...
Command Reference - Page 683
... are the default values:
Table 2-37
Default Values for the Temperature Thresholds
Switch
Difference between Yellow and Red
Catalyst 3560G-48TS
10°C
Catalyst 3560G-48PS
10°C
Catalyst 3560G-24TS
10°C
Catalyst 3560G-24PS
10°C
1.
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
system env temperature threshold yellow
system env temperature threshold yellow...
Command Reference - Page 728
... not return an error if the switch is not in client or transparent mode.
• If the receiving switch is in the pruning-eligible list can be pruned.
• Pruning is then propagated to configure Version 2 on one switch; the version number is supported with VTP Version 1 and Version 2. Follow these guidelines when setting the VTP...
Command Reference - Page 731
... or for the VTP and the VLAN configurations to be set to all VTP or VLAN configuration changes on a switch in server mode, that it does not return an error if the switch is not in client or transparent mode.
• If the receiving switch is saved in VTP. Note VTP configuration in VLAN configuration...
Command Reference - Page 732
... 2 Catalyst 3560 Switch Cisco IOS Commands
Follow these guidelines when configuring a VTP domain name:
• The switch is supported with the vtp domain command. Follow these guidelines when configuring a VTP password:
• Passwords are VTP Version 2-capable, you configure a domain name, it cannot be removed. Passwords should match on one switch; After the switch leaves the no...
Command Reference - Page 733
... status
switchport trunk pruning vtp (global configuration)
Description Displays the VTP statistics for the switch:
Switch(vlan)# vtp domain OurDomainName Changing VTP domain name from cisco to OurDomainName
This example shows how to configure the VTP domain password:
Switch(vlan)# vtp password private Setting device VLAN database password to enable v2 mode in the proposed new VLAN database...
Command Reference - Page 737
Appendix A Catalyst 3560 Switch Boot Loader Commands boot
Related Commands Command set
Description
Sets the BOOT environment variable to boot a specific image when the BOOT keyword is appended to the command.
78-16405-05
Catalyst 3560 Switch Command Reference
A-3
Command Reference - Page 761
...lower network traffic and fewer users. Debugging during troubleshooting sessions with the Catalyst 3560 switch. Caution
Because debugging output is best to troubleshoot specific problems or during these periods decreases the likelihood that have been created or changed for use the debug commands during periods of Cisco technical support staff. These commands are helpful in the CPU...
Command Reference - Page 834
...-tree command. Usage Guidelines The undebug spanning-tree command is the interface between the generic Spanning Tree Protocol (STP) code and the platform-specific code of various switch platforms. Display UplinkFast-event debug messages. Display EtherChannel-support debug messages. Debug Multiple Spanning Tree Protocol events. Display spanning-tree root-event debug messages.
Use the no...
Cisco WS-C3560X-48T-S Reviews
We have not received any reviews for Cisco yet.