Cisco WS-C3560X-48T-L Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-C3560X-48T-L manuals!
Problems with Cisco WS-C3560X-48T-L?
Ask a Question
Free Cisco WS-C3560X-48T-L manuals!
Problems with Cisco WS-C3560X-48T-L?
Ask a Question
Cisco WS-C3560X-48T-L Videos
Cisco WS-C3560X-48T-L $3150 Price Reduction
Duration: :34
Total Views: 7
Duration: :34
Total Views: 7
How to Reset a Cisco WS-C3560X-48T-L to Default Settings
Duration: 3:01
Total Views: 41
Duration: 3:01
Total Views: 41
How to Reset a Cisco WS-C3560X-48T-E to Default Settings
Duration: 3:01
Total Views: 7
Duration: 3:01
Total Views: 7
How to Reset a Cisco WS-C3560X-48T-S to Default Settings
Duration: 3:01
Total Views: 84
Duration: 3:01
Total Views: 84
Popular Cisco WS-C3560X-48T-L Manual Pages
Command Reference - Page 27
... to use the switch command-line interface (CLI) to configure software features. Command modes support specific Cisco IOS commands. These are the main command modes for this document, IP refers to IP version 4 (IPv4) unless there is supported by Cisco IOS software. CH A P T E R
1
Using the Command-Line Interface
The Catalyst 3560 switch is a specific reference to IP version 6 (IPv6...
Command Reference - Page 79
... Command show pagp privileged EXEC command. Clear traffic counters.
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
clear pagp
clear pagp
Use the clear pagp privileged EXEC command to 48.
clear pagp {channel-group-number counters | counters}
Syntax Description
channel... command was changed from 1 to 12 to 1 to clear Port Aggregation Protocol (PAgP) channel-group information.
Command Reference - Page 147
...how to configure the local port to not support flow control by the remote port:
Switch(config)# interface gigabitethernet0/1 Switch(config-if)# flowcontrol receive off
You can verify your settings by entering the show interfaces
Description
Displays the interface settings on the switch, including input and output flow control.
78-16405-05
Catalyst 3560 Switch Command Reference
2-115 The table...
Command Reference - Page 387
... first bootable file that Cisco IOS uses to load and execute when automatically booting.
Displays whether a break during the next boot cycle. Displays a semicolon separated list of the boot loader. Enables manually booting the switch during booting is set to dynamically load during the next boot cycle.
78-16405-05
Catalyst 3560 Switch Command Reference
2-355...
Command Reference - Page 474
... display MLD snooping configuration for the switch or for a specific VLAN. For example, if you have configured a dual IPv4 and IPv6 Switch Database Management (SDM) template on the switch. Switch> show ipv6 mld snooping [vlan vlan-id] [ | {begin | exclude | include expression
(Optional) Specify a VLAN;
Examples
This is running the advanced IP services image and you enter | exclude...
Command Reference - Page 489
...are physical ports and port channels;...Switch> show mac access-group Interface GigabitEthernet0/1:
Inbound access-list is not set...set Interface GigabitEthernet0/4:
Inbound access-list is not set
This is 1 to display the MAC access control lists (ACLs) configured for an interface or a switch. In this display, port... a specific interface.
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
show mac...
Command Reference - Page 493
...
vlan vlan-id
| begin | exclude | include expression
Specify the 48-bit MAC address; the valid format is H.H.H. (Optional) Display information for the specific VLAN only. Expression in the output to use as a reference point. Usage Guidelines
Expressions are case sensitive.
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
show mac address-table address
show mac address...
Command Reference - Page 676
... 2 Catalyst 3560 Switch Cisco IOS Commands
switchport protected
Use the switchport protected interface configuration command to disable protection on the port. All ports are protected ports.
To prevent communication between protected ports on the same switch is possible only through a Layer 3 device. only control traffic, such as PIM packets, is also a protected port. All data traffic...
Command Reference - Page 683
...of this command is only valid on these switches: • Catalyst 3560G-48TS • Catalyst 3560G-48PS • Catalyst 3560G-24TS • Catalyst 3560G-24PS
78-16405-05
Catalyst 3560 Switch Command Reference
2-651 system env temperature threshold yellow value
no form of yellow threshold. Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
system env temperature threshold yellow
system...
Command Reference - Page 728
... must be pruned.
• Pruning is supported with VTP Version 1 and Version 2. Follow these guidelines when setting a VTP password:
• Passwords are configured on a switch in a Token Ring environment, VTP Version 2 must support Version 2; vtp (global configuration)
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
Follow these guidelines when setting VTP mode:
• The no vtp...
Command Reference - Page 731
... changes on a switch in server mode, that it does not return an error if the switch is not in client or transparent mode.
• If the receiving switch is in the switch running configuration file,... changes on the switch and you attempt to set the VTP mode to either server or client mode only when dynamic VLAN creation is saved in VTP. Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
vtp ...
Command Reference - Page 737
Appendix A Catalyst 3560 Switch Boot Loader Commands boot
Related Commands Command set
Description
Sets the BOOT environment variable to boot a specific image when the BOOT keyword is appended to the command.
78-16405-05
Catalyst 3560 Switch Command Reference
A-3
Command Reference - Page 761
... commands during periods of Cisco technical support staff. Debugging during troubleshooting sessions with the Catalyst 3560 switch. Caution
Because debugging output is best to troubleshoot specific problems or during these periods decreases the likelihood that have been created or changed for use with Cisco technical support staff. APPENDIX
B
Catalyst 3560 Switch Debug Commands
This...
Command Reference - Page 832
... debugging.
B-72
Catalyst 3560 Switch Command Reference
78-16405-05
Related Commands Command show debugging
show port-security
Description
Displays information about the types of the port security subsystem.
For syntax information, select Cisco IOS Release 12.2 Configuration Guides and Command References > Cisco IOS Configuration Fundamentals Configuration Guide, Release 12...
Command Reference - Page 834
... the platform-specific code of various switch platforms. Display UplinkFast-event debug messages. Command Modes Privileged EXEC
Command History
Release 12.1(19)EA1
Modification This command was introduced. Display spanning-tree bridge protocol data unit (BPDU) debug messages.
debug spanning-tree
Appendix B Catalyst 3560 Switch Debug Commands
debug spanning-tree
Use the debug spanning...
Cisco WS-C3560X-48T-L Reviews
We have not received any reviews for Cisco yet.