Cisco WS-C3560X-24T-S Support and Manuals
Get Help and Manuals for this Cisco item
View All Support Options Below
Free Cisco WS-C3560X-24T-S manuals!
Problems with Cisco WS-C3560X-24T-S?
Ask a Question
Free Cisco WS-C3560X-24T-S manuals!
Problems with Cisco WS-C3560X-24T-S?
Ask a Question
Cisco WS-C3560X-24T-S Videos
Cisco Catalyst WS-C3560X-24T-L vs WS-C3560X-24T-S
Duration: 4:29
Total Views: 58
Duration: 4:29
Total Views: 58
How to Reset a Cisco WS-C3560X-24T-E to Default Settings
Duration: 3:01
Total Views: 12
Duration: 3:01
Total Views: 12
How to Reset a Cisco WS-C3560X-24T-S to Default Settings
Duration: 3:01
Total Views: 1,973
Duration: 3:01
Total Views: 1,973
How to Reset a Cisco WS-C3560X-24T-L to Default Settings
Duration: 3:01
Total Views: 30
Duration: 3:01
Total Views: 30
Popular Cisco WS-C3560X-24T-S Manual Pages
Hardware Installation Guide - Page 36
... exposed metal parts are located within a restricted access location and users and service people who are authorized within the restricted access location are in the absence of each warning to de-energize the unit. You are made aware of the hazards involved with local and national electrical codes. Statement 1074
Catalyst 3560 Switch Hardware Installation Guide
2-4
OL...
Hardware Installation Guide - Page 38
... end of the link. • Cisco Ethernet Switches are equipped with cooling mechanisms, such as metal flakes from construction activities). Statement 370
Catalyst 3560 Switch Hardware Installation Guide
2-6
OL-6337-07 These standards provide guidelines for the steps required to connect a PC to the switch and to all Cisco Ethernet switches except for this equipment in standby mode.
Set...
Hardware Installation Guide - Page 56
...3560 Switch Hardware Installation Guide
OL-6337-07 You can configure and monitor a switch cluster or an individual switch.
• Use the CLI from anywhere in the Getting Started with a Catalyst 3560 switch.
• Start an SNMP application such as an individual switch. See the Catalyst 3560 Switch Software Configuration Guide and the Catalyst 3560 Switch Command Reference on Cisco.com...
Hardware Installation Guide - Page 60
... parts inside. Statement 1074
Catalyst 3560 Switch Hardware Installation Guide
3-4
OL-6337-07 Contact the appropriate electrical inspection authority or an electrician if you work on Power over Ethernet (PoE) circuits if interconnections are uncertain that could cause bodily injury. All connections must be removed to install, replace, or service this equipment. Statement 1046
Warning...
Hardware Installation Guide - Page 72
...servicing this unit in a 19-inch rack requires a bracket kit that the system remains stable. Figure 3-8
Attaching the 19-inch Brackets for instructions. Connect to the front-panel ports. and 12-Port Switches... with the CLI-Based Setup Program."
4.
Installing the Switch
Chapter 3 Switch Installation (8- See the Catalyst 3560 Switch Getting Started Guide for Rack-Mounting
SYST STAT...
Hardware Installation Guide - Page 76
...Catalyst 3560 Switch Software Configuration Guide and the Catalyst 3560 Switch Command Reference on Cisco.com for information on using the CLI with Cisco Network Assistant guide. You can use any of these management options to Go Next
If the default configuration is described in the opening of a cluster or as the CiscoView application.
3-20
Catalyst 3560 Switch Hardware Installation Guide...
Hardware Installation Guide - Page 77
..., page 4-4
OL-6337-07
Catalyst 3560 Switch Hardware Installation Guide
4-1 See the software configuration guide, the switch command reference guide on the front panel provide troubleshooting information about the switch. For a full description of the switch LEDs, see the "LEDs" section on self-test (POST), port-connectivity problems, and overall switch performance. You can also get...
Hardware Installation Guide - Page 87
Appendix A Technical Specifications
OL-6337-07
Table A-4
Specifications for the Catalyst 3560-24TS-S Switch
Power Requirements AC input voltage
DC input voltages for RPS 675 Power consumption Maximum power consumption Maximum power dissipation Physical Dimensions Weight Dimensions (H x D x W)
100 to 240 VAC (autoranging) 450 to 190 mA, 50 to 60 Hz +12 V @ 5 A 45 W 45 W, 154 BTUs per hour...
Command Reference - Page 19
... switch is for use with the Cisco IOS commands and the switch software features. Preface
Audience
This guide is supported by selecting Technical Support & Documentation > Cisco IOS Software. Before using the Cisco IOS command-line interface (CLI) to manage the Catalyst 3560 switch, hereafter referred to as the switch. The IP services image provides a richer set available from the Layer...
Command Reference - Page 27
... information on the boot loader commands, see the Cisco IOS Release 12.2 Command Summary. Command modes support specific Cisco IOS commands. This chapter describes how to use the switch command-line interface (CLI) to IP version 6 (IPv6). For information on the show platform commands, see Appendix B, "Catalyst 3560 Switch Debug Commands."
For example, the interface interface-id...
Command Reference - Page 728
... VTP updates if there are no -password state. otherwise, you must configure them to operate in VTP Version 1 mode.
• If all switches in...error if the switch is not in client or transparent mode.
• If the receiving switch is disabled. vtp (global configuration)
Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
Follow these guidelines when setting a VTP password:
• Passwords...
Command Reference - Page 731
...switch in VTP. Note VTP configuration in VLAN configuration mode is not changed.
• Switches in transparent mode do not participate in server mode. Follow these guidelines when setting...; If extended-range VLANs are saved in the switch running -config startup-config privileged EXEC command. Chapter 2 Catalyst 3560 Switch Cisco IOS Commands
vtp (VLAN configuration)
Command Modes VLAN...
Command Reference - Page 737
Appendix A Catalyst 3560 Switch Boot Loader Commands boot
Related Commands Command set
Description
Sets the BOOT environment variable to boot a specific image when the BOOT keyword is appended to the command.
78-16405-05
Catalyst 3560 Switch Command Reference
A-3
Command Reference - Page 761
... to troubleshoot specific problems or during troubleshooting sessions with the Catalyst 3560 switch. For this reason, use the debug commands only to use the debug commands during these periods decreases the likelihood that have been created or changed for use .
78-16405-05
Catalyst 3560 Switch Command Reference
B-1 Debugging during periods of Cisco technical support staff. APPENDIX...
Command Reference - Page 834
...Display EtherChannel-support debug messages. Display spanning-tree exception debug messages. Display per-VLAN spanning-tree plus (PVST+) event debug messages. B-74
Catalyst 3560 Switch Command Reference... Display switch shim command debug messages. This shim is the software module that is the interface between the generic Spanning Tree Protocol (STP) code and the platform-specific code of ...
Cisco WS-C3560X-24T-S Reviews
We have not received any reviews for Cisco yet.