Hardware Installation Guide
Page 2
...DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.... harmful interference to cause harmful interference, in which case users will not occur in accordance with Cisco's installation instructions, it off. These specifications are registered...reserved. and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, ...
...DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.... harmful interference to cause harmful interference, in which case users will not occur in accordance with Cisco's installation instructions, it off. These specifications are registered...reserved. and Access Registrar, Aironet, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, ...
Hardware Installation Guide
Page 85
... Leased Line Card to an NT1 Device OK LED Straight-through RJ-48C-to-RJ-48C cable SEE MANUAL BEFORE INSTALLATION BRI S/T LL ISDN BRI leased line interface (RJ-48C) 41191 S/T interface NT1 device ... Step 5 Connect the NT1 device to the ISDN wall jack according to the documentation that the router is OFF or ON. Statement 1026 Warning The ISDN connection is regarded as shown in WAN ports... BRI S/T leased-line WIC to a network. Connect one -time-only plug) must be inaccessible to user contact. Do not attempt to tamper with the NT1 device. ISDN BRI WAN Interface Cards ISDN BRI S/T...
... Leased Line Card to an NT1 Device OK LED Straight-through RJ-48C-to-RJ-48C cable SEE MANUAL BEFORE INSTALLATION BRI S/T LL ISDN BRI leased line interface (RJ-48C) 41191 S/T interface NT1 device ... Step 5 Connect the NT1 device to the ISDN wall jack according to the documentation that the router is OFF or ON. Statement 1026 Warning The ISDN connection is regarded as shown in WAN ports... BRI S/T leased-line WIC to a network. Connect one -time-only plug) must be inaccessible to user contact. Do not attempt to tamper with the NT1 device. ISDN BRI WAN Interface Cards ISDN BRI S/T...
Hardware Installation Guide
Page 92
... integrated data service unit/channel service unit (DSU/CSU). Figure 58 WIC-1DSU-T1 Front Panel T1 port 41215 SEE MANUAL BEFORE INSTALLATION LP AL CD LOOP BACK T1 DSU/CSU DSU CSU T1 LP CD AL Loopback button Figure 59 WIC-...1DSU-T1-V2 Front Panel T1 port 88109 SEE MANUAL BEFORE INSTALLATION LP AL CD T1 DSU/CSU LOOP BACK WIC 1DSU-T1 V2 LP CD AL Loopback button T1/... LEDs and Loopback Button Color Yellow Off Description Line or loopback state is detected or is manually set by the user. There are shown in Table 13.
... integrated data service unit/channel service unit (DSU/CSU). Figure 58 WIC-1DSU-T1 Front Panel T1 port 41215 SEE MANUAL BEFORE INSTALLATION LP AL CD LOOP BACK T1 DSU/CSU DSU CSU T1 LP CD AL Loopback button Figure 59 WIC-...1DSU-T1-V2 Front Panel T1 port 88109 SEE MANUAL BEFORE INSTALLATION LP AL CD T1 DSU/CSU LOOP BACK WIC 1DSU-T1 V2 LP CD AL Loopback button T1/... LEDs and Loopback Button Color Yellow Off Description Line or loopback state is detected or is manually set by the user. There are shown in Table 13.
Hardware Installation Guide
Page 133
...This LED is turned off. Note Refer to the router. Step 5 Confirm that came with another DSU/CSU. Turn on the card. (See Figure 99.) Figure 99 Connecting a Multiflex Trunk Interface Card RJ-48C ports AL SEE VWIC 2MFT-E1-D1 LP MANUAL CD BEFORE CTRLR E1 1 CTRLR E1 0 INSTALLATION ...through RJ-48C-to-RJ-48C cable to the T1 or E1 port on power to the Cisco Modular Access Router Specifications for network-end connectors and pinouts of interface card. This LED is manually set by the user. A carrier has been detected, and the internal DSU/CSU in Table 27. This LED...
...This LED is turned off. Note Refer to the router. Step 5 Confirm that came with another DSU/CSU. Turn on the card. (See Figure 99.) Figure 99 Connecting a Multiflex Trunk Interface Card RJ-48C ports AL SEE VWIC 2MFT-E1-D1 LP MANUAL CD BEFORE CTRLR E1 1 CTRLR E1 0 INSTALLATION ...through RJ-48C-to-RJ-48C cable to the T1 or E1 port on power to the Cisco Modular Access Router Specifications for network-end connectors and pinouts of interface card. This LED is manually set by the user. A carrier has been detected, and the internal DSU/CSU in Table 27. This LED...