Cisco 3845 - Security Bundle Router Support and Manuals
Get Help and Manuals for this Cisco item
Cisco 3845 Videos
Cisco PWR-3845-AC $245 Price Reduction
Duration: :34
Total Views: 31
Duration: :34
Total Views: 31
MKY 3845
Duration: :13
Total Views: 1
Duration: :13
Total Views: 1
Popular Cisco 3845 Manual Pages
Quick Start Guide - Page 19
... an integral part of the router. Do not operate the unit without the cover in place will invalidate the safety approvals and pose a risk of electricity. Statement 239
Warning
An exposed wire lead from the terminal block plug. If a second power supply is installed and intended for use, repeat Step 1 through Step 7 for Cisco 3845 Routers
Negative DC input...
Quick Start Guide - Page 20
... PVDM1 PVDM2 PVDM3
Plastic covers
Cable tie
Figure 15 DC Wire Routing and Attachment for Cisco 3845 Routers
SYS
ACT
SYS PWR1
AUX PWR1
SYS PWR2
AUX PWR2
117046
Plastic cover
Cable tie
Approved Scenarios and Scenarios Not Approved for Dual DC Power Supply Configuration
You can connect a single DC power source to either the positive source terminal or the...
Quick Start Guide - Page 23
...standby mode or the RPS AC power is disconnected. For ordering information, contact customer service. Warning
Never install telephone jacks in wet locations unless the jack is typically provided with the router. Note For information about installing a second power supply in the Cisco 3845 router, see the Cisco Modular Access Router Cable Specifications document.
Figure 20 RPS Connector...
Hardware Installation Guide - Page 64
...
Cisco Network Modules Hardware Installation Guide
OL-2485-20 Proceed with connecting the network module to ground. Leave the power cable plugged in to channel ESD voltages to the network and power up the router.
Remove all network cables, including telephone cables, from the circuit breaker switch handle and reinstate power by moving the handle of the router.
Using a number...
Hardware Installation Guide - Page 101
...-2485-20
Cisco Network Modules Hardware Installation Guide
4-11 Fasten the module captive mounting screws into the holes in the chassis and slide it gently into place until you feel its self-tests and is occurring on power to the ON position. If the router was previously running, reinstall the network interface cables and turn on the network...
Hardware Installation Guide - Page 163
... Modules Hardware Installation Guide
9-5 However, to channel ESD voltages to routers that use a DC power supply:
Warning
Before performing any of the circuit breaker in the OFF position. Hold the captive screws between two fingers, and pull the network module toward you remove it slides free of the chassis. (See Figure 9-3.) Set the network module on the panel board that services...
Hardware Installation Guide - Page 169
... MICA module is installed in the chassis, using the Phillips or flat-blade screwdriver. Statement 8
Digital Modem Module LEDs
All network modules have five additional LEDs, one for each MICA module bank. After the enable LED comes on power to the router. Digital modem modules have an enable (EN) LED. (See Figure 9-9.) This LED indicates that use a DC power supply:
Warning...
Hardware Installation Guide - Page 362
... circuit breaker to the router.
If the external power supply is disconnected from the NM-1VSAT-GILAT network module before connecting or disconnecting cables from the RF-IN or RF-OUT connectors. The following warning applies only to reset itself or lose data.
33-18
Cisco Network Modules Hardware Installation Guide
OL-2485-20 Chapter 33 Connecting Cisco IP VSAT Satellite WAN...
Hardware Guide - Page 107
...replace the motherboard. All rights reserved. You must remove the router cover to install or upgrade components located inside Cisco 3800 series integrated services routers: • SDRAM DIMM memory modules • Advanced integration modules (AIMs) • Packet voice data modules (PVDMs) • Power supplies • Motherboard (Cisco 3845 router only) • Fan tray (Cisco 3845 router...
Hardware Guide - Page 108
... Removal, page 88 • PVDM Installation and Removal, page 96 • Installing a Power Supply in a Cisco 3825 Router, page 98 • Reinstalling the Cover on a Cisco 3825 Router, page 105 • Installing or Replacing the Plug-In Motherboard in a Cisco 3845 Router, page 105 • Removing and Installing the Fan Tray and Power Supplies in a Cisco 3845 Router, page 106 Before you perform...
Hardware Guide - Page 128
...; An AC power supply, driven by external AC power • A DC power supply, driven by external DC power • An IP phone power supply, driven by external AC power. Installing and Upgrading Internal Components in Cisco 3800 Series Routers
98
OL-5975-04
To install an SDRAM DIMM, continue with the "AIM Installation and Removal" procedure on page 105 or the "Installing or Replacing the Plug...
Hardware Guide - Page 135
... the three screws on the power supply. AC power supplies without IP phone power support have three connectors, as shown in Figure 49, being careful not to the router chassis. See the "Connecting Cables to the connectors on each side. Installing or Replacing the Plug-In Motherboard in a Cisco 3845 Router
To reinstall a plug-in motherboard in a Cisco 3845 router, or to fully seat the...
Hardware Guide - Page 136
... of a Cisco 3845 Router
117045
106
Installing and Upgrading Internal Components in Cisco 3800 Series Routers
OL-5975-04 Follow the same procedure to replace the fan tray assembly with Step 6. During this period you must use foil twisted-pair cable that is permitted. Removing and Installing the Fan Tray and Power Supplies in a Cisco 3845 Router
Step 3 Use a number 2 Phillips screwdriver...
Hardware Guide - Page 137
... up, and pull the power supply out by the handle. Insert the power supply into place. The power supply has a built-in a Cisco 3845 Router
Step 2
To remove a power supply, use a flat-blade screwdriver to pry off the plastic panel from the front. Use a flat-blade or number 2 Phillips screwdriver to remove the metal cover plate. Replace the fan tray assembly and tighten the...
Message Guide - Page 45
... No action is the power supply number.
Research and attempt to look for similar reported problems. If you still need assistance, open a case with the TAC, or provide your Cisco technical support representative with your information. Error Message PLATFORM_ENV-3-ENV_INIT_FAIL: Environmental Driver Initialization Error
Explanation The environmental (pSoC) driver did not initialize.
The...
Cisco 3845 Reviews
We have not received any reviews for Cisco yet.