Cisco 2511 - Router - EN Support and Manuals
Get Help and Manuals for this Cisco item
Most Recent Cisco 2511 Questions
How Can I Get A New Password For My Wifi, Without Buying A New Router?
(Posted by Anonymous-46816 12 years ago)
Cisco 2511 Videos
Configuring a Cisco Access Server 2509 - 2511 PART 2
Duration: 9:58
Total Views: 10,378
Duration: 9:58
Total Views: 10,378
2511 Access Server
Duration: 6:17
Total Views: 867
Duration: 6:17
Total Views: 867
Configuring a Cisco Access Server 2509 - 2511 PART 1
Duration: 8:20
Total Views: 21,212
Duration: 8:20
Total Views: 21,212
2511 Access Server Part 2
Duration: 9:57
Total Views: 531
Duration: 9:57
Total Views: 531
Popular Cisco 2511 Manual Pages
Getting Started Guide - Page 3
...'s instructions. Replace the battery only with four 4 Gigabit Ethernet ports.
3 Dispose of explosion if the battery is replaced incorrectly. Statement 1024
Warning
Ultimate disposal of 5 access points, making it a cost-effective solution for the Teleworker solution. The 2504 controllers supports up to 50 lightweight access points in the absence of the electrical ground before installing...
Getting Started Guide - Page 4
... best use this guide, you can use straight-through or crossover cables. Figure 1 shows a 2504 controller network topology and network connections, showing the medium dependent interface (MDI) Ethernet cables required. Figure 1 Typical Controller Topology and Network Connections
Console emulator for initial boot-up
Null modem serial cable (DB-9 -> RJ-45) to console connection
Cisco WCS software...
Getting Started Guide - Page 5
... that the stored baud rate setting matches one of the LED manufacturer's specifications and is not available; however the bootloader ensures that supports a RJ-45 connector. If a nonstandard value is expected that there will default to unit.
At boot-up the controller configures the RS-232 port as a console port with default settings of the front panel...
Getting Started Guide - Page 11
... reach the controller and all cables attached to the Cisco Wireless LAN Controller Configuration Guide for this installation.
• RADIUS server IP address, communications port, and secret if you install it is more secure and reliable if you are configuring a RADIUS server, such as 10.40.0.3, 1812, and mysecretcode.
• The country code for country code information. Enter help to...
Getting Started Guide - Page 21
...
If the relief clip is not installed, the power connector can configure the 2504 controller for the following parameters:
• 9600 baud • 8 data bits • No flow control • 1 stop bit • No parity
Securing the Power Adapter Cable
To secure the power adapter cable to the controller console port, follow these steps:
Step...
Getting Started Guide - Page 24
... override CF Bus 0 (IDE): OK IDE device 0: - Clear configuration 5. Do not reboot the controller until the user login prompt appears. Run backup image (7.0.114.75) 3. Manually update images Enter selection:
If you did not press Esc, the boot process continues and takes two to access the Boot Menu... Model: 1GB CompactFlash Card Firm: CF B612J Ser#: C181101244A1Yb3A5QNU...
Getting Started Guide - Page 25
... Starting Fastpath Console redirect : ok Starting Fastpath DP Heartbeat : ok Fastpath CPU00: Starting Fastpath Application. Num of Cisco Systems, Inc. Starting Switching Services: ok Starting QoS Services: ok Starting Policy Manager: ok Starting Data Transport Link Layer: ok Starting Access Control List Services: ok Starting System Interfaces: ok Starting Client Troubleshooting Service: ok...
Getting Started Guide - Page 26
...: ok Starting RRC Services: ok Starting FMC HS: ok Starting Management Services:
Web Server: ok CLI: ok
Secure Web: Web Authentication Certificate not found (error). If you cannot access management interface via HTTPS please reconfigure Virtual Interface. License Agent: ok
(Cisco Controller)>
Step 4 If desired, press Esc key to interrupt the boot process and access the Boot menu.
26
Getting Started Guide - Page 27
Run primary image (7.0.114.76) - Loading primary image (7.0.114.76) 100% 31427987 bytes read Launching images... Software Copyright Cisco Systems, Inc. Change active boot image 4. Clear configuration 5. Installing ether-pow driver - 0x6008 starting pid 672, tty '': '/etc/init.d/rcS' type = block dump-device = 254:4 disrupt level = header compress = none ifconfig: SIOCGIFFLAGS: No such device ...
Getting Started Guide - Page 30
... the controller. You can enter up to match the switch interface configuration. Enter the IP address of the access point manager interface. Enter the port number of the management interface netmask. Table 3
Startup Wizard Information
Wizard Setting System Name Administrative user name
Administrative password
Action
Enter the system name, which is the name you...
Getting Started Guide - Page 31
... a RADIUS server.
All controllers within a mobility group must be configured with the same virtual interface IP address. All of the mobility group/RF group to which you enter here is used to belong.
Values are usually also in an RF group are yes or no. Network Name (SSID)
Enter the network name, or service set identifier...
Getting Started Guide - Page 33
... these steps:
Step 1 Enter a valid username and password to log into the controller CLI. prompt. If yes is correct. Values are case sensitive.
33
Enter yes if the configuration entered is entered. the controller saves your configuration, reboots, and prompts you created in the "Configure a NTP Server Now?"
Configuration correct? Note
This prompt only displays if...
Getting Started Guide - Page 35
... 14. Note Direct connection of access points to meet the specific needs of your wireless network.
35 Note If the link does not activate, check the cable. Refer to the Cisco Wireless LAN Controller Configuration Guide for basic operation. When you have prepared the controller for information on configuring the controller to Cisco 2500 Series Wireless Controllers are...
Getting Started Guide - Page 36
.... The installation is available on the front panel of the controller becomes active after the controller boots. See Table 1 on page 5 for more information about configuring your 2504 controller is not working properly, check the LEDs on cisco.com. Figure 14 Access Points Connected to a Controller
Network
Cisco 2504 Wireless Controller
10/100/1000BASE-T MDI cable
Network...
Getting Started Guide - Page 55
...), not regulated with the subject law by Cisco. Using any other cables/adaptors could cause a malfunction or a fire. Install and use the provided or designated connection cables/power cables/AC adaptors/batteries.
Statement 371-Power Cable and AC Adapter
When installing the product, please use the equipment according to the instruction manual.
55 Statement 157-VCCI Compliance for...
Cisco 2511 Reviews
We have not received any reviews for Cisco yet.