Getting Started Guide
Page 5
.... 5 Note It is an RS-232 port that the stored baud rate setting matches one of the LED manufacturer's specifications and is not available; Figure 2 Front Panel and LEDs 282249 CONSOLE CONSOLE CISCO 2500 Series WIRELESS CONTROLLER RESET Model 2504 1 2 3 4 PWR SYS ALM RESET 1 2 3-4 POE PWR ALM SYS Table 1 Callout WLC2504 Front...
.... 5 Note It is an RS-232 port that the stored baud rate setting matches one of the LED manufacturer's specifications and is not available; Figure 2 Front Panel and LEDs 282249 CONSOLE CONSOLE CISCO 2500 Series WIRELESS CONTROLLER RESET Model 2504 1 2 3 4 PWR SYS ALM RESET 1 2 3-4 POE PWR ALM SYS Table 1 Callout WLC2504 Front...
Getting Started Guide
Page 6
...factor. If software needs to I2C address 0x40/41 (0100 000r/w). This port is designed so that 1500 VAC rms isolation (per the 802.3 specification) is configured to reset the POE controller, it can be used for infra-switch connection using multiple an AP-Manager or data interface. 6 They... -Ethernet (POE) ports The Gigabit POE ports are PoE only ports; This port is designed so that 1500 VAC rms isolation (per the 802.3 specification) is an RJ-45 connector form-factor. LED description: • Green or Blinking Green-Link activity • Off-No link 2 GigE port and...
...factor. If software needs to I2C address 0x40/41 (0100 000r/w). This port is designed so that 1500 VAC rms isolation (per the 802.3 specification) is configured to reset the POE controller, it can be used for infra-switch connection using multiple an AP-Manager or data interface. 6 They... -Ethernet (POE) ports The Gigabit POE ports are PoE only ports; This port is designed so that 1500 VAC rms isolation (per the 802.3 specification) is an RJ-45 connector form-factor. LED description: • Green or Blinking Green-Link activity • Off-No link 2 GigE port and...
Getting Started Guide
Page 23
... the controller. If the Power LED does not light, make sure that the power connections to 240 VAC, 50-60 Hz electrical outlet. Plug a country-specific power cord into the external power supply, then plug the other end into memory, verifies its operating system software load, and initializes itself with screw...
... the controller. If the Power LED does not light, make sure that the power connections to 240 VAC, 50-60 Hz electrical outlet. Plug a country-specific power cord into the external power supply, then plug the other end into memory, verifies its operating system software load, and initializes itself with screw...
Getting Started Guide
Page 35
... Radio Resource Management (RRM) feature automatically configures the access point to start transmitting and allowing clients to meet the specific needs of access points to Cisco 2500 Series Wireless Controllers are connecting to make the connections. Note If the link does not activate, check the... cable. You have configured the controller, use Category-5, Category-5e, Category-6, or Category-7 Ethernet cables to connect up to 50 Cisco lightweight access points to the controller Ethernet ports or to the network (distribution system) as the controller is operational, the controller is...
... Radio Resource Management (RRM) feature automatically configures the access point to start transmitting and allowing clients to meet the specific needs of access points to Cisco 2500 Series Wireless Controllers are connecting to make the connections. Note If the link does not activate, check the... cable. You have configured the controller, use Category-5, Category-5e, Category-6, or Category-7 Ethernet cables to connect up to 50 Cisco lightweight access points to the controller Ethernet ports or to the network (distribution system) as the controller is operational, the controller is...