Cisco 2950G 24 - Catalyst Switch Support and Manuals
Get Help and Manuals for this Cisco item
This item is in your list!
View All Support Options Below
Free Cisco 2950G 24 manuals!
Problems with Cisco 2950G 24?
Ask a Question
Free Cisco 2950G 24 manuals!
Problems with Cisco 2950G 24?
Ask a Question
Cisco 2950G 24 Videos
Popular Cisco 2950G 24 Manual Pages
Software Configuration Guide - Page 25
... supported by the switch software. The 2950 LRE switch is supported by using this guide does not provide the command-line interface (CLI) procedures.
For a list of switches that have assigned switch IP information and passwords by an a variation of service (QoS) features, the Secure Shell Protocol, extended-range VLANs, and Remote Switch Port Analyzer (RSPAN). Before using the setup...
Software Configuration Guide - Page 26
... Documentation home page, select Release 12.1 from the Cisco.com home page at Service and Support > Technical Documents. Do not install release 12.1(11)EA1 on Catalyst 2950 LRE switches, and do not install release 12.1(11)YJ on your web browser and accessing CMS, refer to the IOS documentation set system name and prompt, create a login banner, and...
Software Configuration Guide - Page 33
... use the YJ release for non-LRE switches only; Table 1-1 Switches Supported
Switch Catalyst 2950-12
Software Image
SI1
Catalyst 2950-24
SI
Catalyst 2950C-24
EI2
Catalyst 2950G-12-EI
EI
Catalyst 2950G-24-EI
EI
Catalyst 2950G-24-EI-DC EI
Catalyst 2950G-48-EI
EI
Catalyst 2950SX-24
SI
Catalyst 2950T-24
EI
Catalyst 2950ST-24-LRE
YJ3
Catalyst 2950ST-8-LRE
YJ
1.
Overview
CH...
Software Configuration Guide - Page 35
The Catalyst 2950G-12-EI, 2950G-24-EI, 2950G-24-EI-DC,
and 2950G-48-EI switches running Cisco IOS Release 12.1(6)EA2 or later support frame sizes from 1500 to 1530 bytes • Per-port broadcast storm control for preventing faulty end stations from degrading overall system performance with broadcast storms • Port Aggregation Protocol (PAgP) for automatic creation of EtherChannel links ...
Software Configuration Guide - Page 52
...Cisco CWDM Passive Optical System. Up to eight CWDM GBIC modules, with the switches translates to farther data transmission and an increased bandwidth capacity (up to 1610 nanometers (nm). Figure 1-7 shows a configuration for long-distance transmissions is sent at wavelengths from one location to the Catalyst 2950 LRE switches. The Catalyst switches have the EI installed on your Catalyst...
Software Configuration Guide - Page 74
...8226; Cisco RPS 600 (model PWR600-AC-RPS)-Catalyst 2900 XL and Catalyst 3500 XL switches, except the Catalyst 2900 LRE XL and Catalyst 3524-PWR XL switches
Refer to the appropriate switch hardware documentation for RPS descriptions specific for the switch.
Note The bandwidth utilization mode (UTIL LED) does not appear on the RPS. Catalyst 2950 Desktop Switch Software Configuration Guide...
Software Configuration Guide - Page 115
... a set of events on the Configuration Registrar. This unique identifier can use the namespace mapping service to those configured in Cisco IOS software;
The event service uses namespace content for receipt and generation of configuration events. Within the scope of the configuration server namespace, the term configID is reconfigured.
78-14982-01
Catalyst 2950 Desktop Switch...
Software Configuration Guide - Page 117
...
The CNS configuration agent feature supports the switch by providing: • Initial configurations • Incremental (partial) configurations • Synchronized configuration updates
Initial Configuration
When the switch first comes up, it attempts... relay agent default gateway
71445
Access layer switches
78-14982-01
Catalyst 2950 Desktop Switch Software Configuration Guide
5-5
Software Configuration Guide - Page 119
...to communicate with the IE2100 Configuration Registrar.
• Configure the switch to use either the switch MAC address or the serial number (instead of the device to the Cisco Intelligence Engine 2100 Series Configuration Registrar Manual.
78-14982-01
Catalyst 2950 Desktop Switch Software Configuration Guide
5-7
Note For more templates for Enabling Automatic Configuration
Device Access...
Software Configuration Guide - Page 263
...monitor to log events, set traps, change to an LRE switch, the expected duration of LRE binaries.
78-14982-01
Catalyst 2950 Desktop Switch Software Configuration Guide
10-15
A link ...the firmware on traffic levels).
• PMD Freeze Event Counter: Counts the occurrence of LRE upgrade configuration commands is not supported. Micro-interruptions and ADC saturations are updates ...
Software Configuration Guide - Page 369
...switches and have those changes automatically communicated to all the other switches. Extended-range VLANs (VLAN IDs greater than 1005) are only supported when the enhanced software image (EI... 15-4
78-14982-01
Catalyst 2950 Desktop Switch Software Configuration Guide
15-1 Without VTP, you...problems, such as duplicate VLAN names, incorrect VLAN-type specifications, and security violations.
Software Configuration Guide - Page 376
... VTP messages with the correct password. After the configuration, the switch accepts the next VTP advertisement that belong to a version that does support VTP, ports that uses the same password and domain name in the advertisement. Upgrading from Previous Software Releases
When you must configure the password on it.
Passwords
You can configure a password for the VTP domain, but...
Software Configuration Guide - Page 502
... bit. Differentiated Services Code Point (DSCP) X
X
IP source address
X
X
IP destination address
X
X
Fragments
-
-
Some protocols also have specific parameters and keywords that protocol.
No support for type of service (ToS) byte2
-
- TCP or UDP Layer 4 Parameters
X
X
Source port operator
X
X
Source port
X
X
Destination port operator
X
X
Destination port
X
X
TCP...
Software Configuration Guide - Page 576
...
Using Debug Commands
This section explains how you use debug commands to troubleshoot specific problems or during troubleshooting sessions with Cisco technical support staff. Debugging during these periods decreases the likelihood that debugging is displayed, consider these possibilities: • The switch might not generate the type of lower network traffic and fewer users...
Software Configuration Guide - Page 644
...traps configuring MAC address notification 7-56 configuring managers 24-10 defined 24-3 enabling 7-56, 24-10 notification types 24-10 overview 24-1, 24-4
IN-28
Catalyst 2950 Desktop Switch Software Configuration Guide
troubleshooting detecting unidirectional links 19-1 displaying crash information 28-15 GBIC security and identification 28-13 LRE ports 28-12 statistics 28-1 CPE Ethernet links 28...
Cisco 2950G 24 Reviews
Do you have an experience with the Cisco 2950G 24 that you would like to share?
Earn 750 points for your review!
We have not received any reviews for Cisco yet.
Earn 750 points for your review!