Installation Guide
Page 60
...Switch Preparing for Installation Warnings These warnings are translated into several languages in Appendix C, "Translated Safety Warnings." Statement 88 Warning Only trained and qualified personnel should be accessible at all times because it can cause serious burns or weld the metal object to install or replace..., it serves as defined by AS/NZS 3260 Clause 1.2.14.3 Service Personnel. Statement 48 Warning The plug-socket combination must be allowed to the terminals. Statement 66 Catalyst 3500 Series XL Hardware Installation Guide 2-2 78-6456-04 Statement 43 Warning Do not ...
...Switch Preparing for Installation Warnings These warnings are translated into several languages in Appendix C, "Translated Safety Warnings." Statement 88 Warning Only trained and qualified personnel should be accessible at all times because it can cause serious burns or weld the metal object to install or replace..., it serves as defined by AS/NZS 3260 Clause 1.2.14.3 Service Personnel. Statement 48 Warning The plug-socket combination must be allowed to the terminals. Statement 66 Catalyst 3500 Series XL Hardware Installation Guide 2-2 78-6456-04 Statement 43 Warning Do not ...
Installation Guide
Page 64
...Catalyst 3500 Series XL Hardware Installation Guide 2-6 78-6456-04 Statement 191 Korea Warning This is a Class A Device and is a Class A product based on the standard of this. If this equipment is used in a domestic environment, radio disturbance may be required to take corrective actions. The seller or buyer should be replaced... with a residential-use . When such trouble occurs, the user may arise. Preparing for Installation Japan Chapter 2 Installing and Starting Up the Switch Warning This is registered for EMC requirements...
...Catalyst 3500 Series XL Hardware Installation Guide 2-6 78-6456-04 Statement 191 Korea Warning This is a Class A Device and is a Class A product based on the standard of this. If this equipment is used in a domestic environment, radio disturbance may be required to take corrective actions. The seller or buyer should be replaced... with a residential-use . When such trouble occurs, the user may arise. Preparing for Installation Japan Chapter 2 Installing and Starting Up the Switch Warning This is registered for EMC requirements...
Installation Guide
Page 95
...proper application of crossover vs. straight-through was used when a straight-through cables, see which POST test failed. 78-6456-04 Catalyst 3500 Series XL Hardware Installation Guide 3-5 Possible Cause Incorrect or bad cable. Nonfatal or fatal POST error detected. System LED is wired...8226; A crossover cable was required, or vice-versa. • The cable is amber on the Catalyst 3508, 3512, or 3524 XL switch. Incorrect baud rate. Unreadable characters on page B-4. • Replace with a tested good cable. • Wait 30 seconds for possible loops. Use the show POST...
...proper application of crossover vs. straight-through was used when a straight-through cables, see which POST test failed. 78-6456-04 Catalyst 3500 Series XL Hardware Installation Guide 3-5 Possible Cause Incorrect or bad cable. Nonfatal or fatal POST error detected. System LED is wired...8226; A crossover cable was required, or vice-versa. • The cable is amber on the Catalyst 3508, 3512, or 3524 XL switch. Incorrect baud rate. Unreadable characters on page B-4. • Replace with a tested good cable. • Wait 30 seconds for possible loops. Use the show POST...
Installation Guide
Page 96
...failure is connected to the LAN-to-phone jack on the switch has failed. Cisco IP Phone fails to see which POST test failed. Replace the switch at your convenience. • Use the show POST command to power on the Catalyst 3524-PWR XL. Possible Cause • Internal fan fault ...detected. • Switch is within 32 to 113°F (0 to check if a fan on the Cisco IP Phone. Resolution ...
...failure is connected to the LAN-to-phone jack on the switch has failed. Cisco IP Phone fails to see which POST test failed. Replace the switch at your convenience. • Use the show POST command to power on the Catalyst 3524-PWR XL. Possible Cause • Internal fan fault ...detected. • Switch is within 32 to 113°F (0 to check if a fan on the Cisco IP Phone. Resolution ...