Administration Guide
Page 24
... to show network activity and is solid when there is a link. • The Cisco ATA 186 RJ-45 LED is solid when the Cisco ATA is powered on , then turns off if there is capable of the unit (see Figure 1-7). The Cisco ATA186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. Figure 1-7 Function Button...
... to show network activity and is solid when there is a link. • The Cisco ATA 186 RJ-45 LED is solid when the Cisco ATA is powered on , then turns off if there is capable of the unit (see Figure 1-7). The Cisco ATA186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. Figure 1-7 Function Button...
Administration Guide
Page 118
... H.323/SIP gateways • mgcp fax t38 inhibit for MGCP gateways Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for Cisco AS5300. User is operating Cisco recommends using Cisco ATA models 186-I1, 186-I2, 188-I1, or Cisco ATA software on a dial-peer level or system level. The Cisco 6608 supports both the NSE and NTE methods of the CLI...
... H.323/SIP gateways • mgcp fax t38 inhibit for MGCP gateways Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for Cisco AS5300. User is operating Cisco recommends using Cisco ATA models 186-I1, 186-I2, 188-I1, or Cisco ATA software on a dial-peer level or system level. The Cisco 6608 supports both the NSE and NTE methods of the CLI...
Administration Guide
Page 122
... fax sessions still fail, check that the following conditions are true: • The Cisco ATA software image version is 2.14 or above . • The Cisco ATA model number is ATA186-I1, ATA186-I2, ATA 188-I1, or ATA188-I2. • The fax relay option for the remote gateways has been disabled. The ...terminating gateway may not be compatible with fax/modem pass-through. • The fax pass-through and fax relay events. 6-12 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for G.711A-law) appear in the Enable encoder and DPKT 1st debug lines. Using rtpcatch for...
... fax sessions still fail, check that the following conditions are true: • The Cisco ATA software image version is 2.14 or above . • The Cisco ATA model number is ATA186-I1, ATA186-I2, ATA 188-I1, or ATA188-I2. • The fax relay option for the remote gateways has been disabled. The ...terminating gateway may not be compatible with fax/modem pass-through. • The fax pass-through and fax relay events. 6-12 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for G.711A-law) appear in the Enable encoder and DPKT 1st debug lines. Using rtpcatch for...
Administration Guide
Page 171
...have reasonably low network jitter, network delay, and packet-loss rate. Enhanced fax pass-through and G.711 fax mode. OL-4652-01 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for two sets of frequencies and single set of fax transmissions up to 14.4 kbps depends on... microF (per line) Ringer equivalence number (REN) Up to 5 REN per RJ-11 FXS port Loop impedance Up to those conditions. The Cisco ATA186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. Success of on/off -hook characteristics On-hook voltage (tip/ring) -50V ...
...have reasonably low network jitter, network delay, and packet-loss rate. Enhanced fax pass-through and G.711 fax mode. OL-4652-01 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for two sets of frequencies and single set of fax transmissions up to 14.4 kbps depends on... microF (per line) Ringer equivalence number (REN) Up to 5 REN per RJ-11 FXS port Loop impedance Up to those conditions. The Cisco ATA186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. Success of on/off -hook characteristics On-hook voltage (tip/ring) -50V ...