Administration Guide
Page 25
... The Cisco ATA 186 and Cisco ATA 188 are not sure of the applicable configuration, check your specific application. The Cisco ATA 186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. Note The Cisco ATA186-I1 and Cisco ATA188-I1 provide 600-ohm resistive impedance. Figure 1-5 shows the rear panel of the Cisco ATA 188. Figure 1-6 shows the rear panel of the Cisco ATA 186.
... The Cisco ATA 186 and Cisco ATA 188 are not sure of the applicable configuration, check your specific application. The Cisco ATA 186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. Note The Cisco ATA186-I1 and Cisco ATA188-I1 provide 600-ohm resistive impedance. Figure 1-5 shows the rear panel of the Cisco ATA 188. Figure 1-6 shows the rear panel of the Cisco ATA 186.
Administration Guide
Page 160
... supports both the NSE and NTE methods of fax pass-through mode and cause fax failure. Cisco recommends using the external T1 clock. User is operating Cisco recommends using Cisco ATA models 186-I1, 186-I2, 188-I1, or Cisco ATA software on some Cisco gateways. For fax pass-through mode, AudioMode should be reconfigured to disable fax relay for the Phone...
... supports both the NSE and NTE methods of fax pass-through mode and cause fax failure. Cisco recommends using the external T1 clock. User is operating Cisco recommends using Cisco ATA models 186-I1, 186-I2, 188-I1, or Cisco ATA software on some Cisco gateways. For fax pass-through mode, AudioMode should be reconfigured to disable fax relay for the Phone...
Administration Guide
Page 164
...tool that only 0 (for G.711µ-law) or 8 (for H.323 (version 3.0) OL-4804-01 The tool runs on the Cisco ATA. Debugging the Cisco ATA 186/188 Fax Services Chapter 7 Configuring and Debugging Fax Services • The fax pass-through and fax relay events. You must confirm that ... the terminating gateway may not be compatible with fax mode, only G.711 codecs are true: • The Cisco ATA software image version is 2.14 or above . • The Cisco ATA model number is ATA186-I1, ATA186-I2, ATA 188-I1, or ATA188-I2. • The fax relay option for a VoIP connection.
...tool that only 0 (for G.711µ-law) or 8 (for H.323 (version 3.0) OL-4804-01 The tool runs on the Cisco ATA. Debugging the Cisco ATA 186/188 Fax Services Chapter 7 Configuring and Debugging Fax Services • The fax pass-through and fax relay events. You must confirm that ... the terminating gateway may not be compatible with fax mode, only G.711 codecs are true: • The Cisco ATA software image version is 2.14 or above . • The Cisco ATA model number is ATA186-I1, ATA186-I2, ATA 188-I1, or ATA188-I2. • The fax relay option for a VoIP connection.
Administration Guide
Page 205
... Off-hook current 27 mA (nominal) RJ-11 FXS port terminating impedance option The Cisco ATA186-I1 and Cisco ATA188-I1 provide 600-ohm resistive impedance. The Cisco ATA186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. OL-4804-01 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for each RJ-11 FXS port (SLIC...
... Off-hook current 27 mA (nominal) RJ-11 FXS port terminating impedance option The Cisco ATA186-I1 and Cisco ATA188-I1 provide 600-ohm resistive impedance. The Cisco ATA186-I2 and Cisco ATA188-I2 provide 270 ohm + 750 ohm // 150-nF complex impedance. OL-4804-01 Cisco ATA 186 and Cisco ATA 188 Analog Telephone Adaptor Administrator's Guide for each RJ-11 FXS port (SLIC...