User Guide
Page 1
... ATM • LAN Emulation (LANE) Finding Feature Information in This Module Your Cisco IOS software release may not support all the features documented in which each connection. To access Cisco Feature Navigator, go /cfn. All rights reserved. Configuring the Cisco NM-1A-T3/E3 Network Module OL-10215-01 First Published: June 28, 2007 The Cisco NM-1A-T3/E3 (or ATM T3/E3) network module provides Asynchronous Transfer Mode (ATM) services on Cisco...
... ATM • LAN Emulation (LANE) Finding Feature Information in This Module Your Cisco IOS software release may not support all the features documented in which each connection. To access Cisco Feature Navigator, go /cfn. All rights reserved. Configuring the Cisco NM-1A-T3/E3 Network Module OL-10215-01 First Published: June 28, 2007 The Cisco NM-1A-T3/E3 (or ATM T3/E3) network module provides Asynchronous Transfer Mode (ATM) services on Cisco...
User Guide
Page 2
... configure the ATM T3/E3 network module for T3 or E3 before it will work. • The atm vc-per-vp command is no default card type configuration on the ATM T3/E3 network module. Virtual Circuits A virtual circuit (VC) is a point-to the Cisco ATM T3/E3 network module: • There is not supported on the ATM T3/E3 network module. Restrictions for the Cisco ATM T3/E3 Network Module Configuring the Cisco NM-1A-T3/E3 Network Module • SVCs, page 11 • Customizing the ATM T3/E3 Network Module, page 15 • Configuration...
... configure the ATM T3/E3 network module for T3 or E3 before it will work. • The atm vc-per-vp command is no default card type configuration on the ATM T3/E3 network module. Virtual Circuits A virtual circuit (VC) is a point-to the Cisco ATM T3/E3 network module: • There is not supported on the ATM T3/E3 network module. Restrictions for the Cisco ATM T3/E3 Network Module Configuring the Cisco NM-1A-T3/E3 Network Module • SVCs, page 11 • Customizing the ATM T3/E3 Network Module, page 15 • Configuration...
User Guide
Page 3
... IP packets • Flow, and Cisco Express Forwarding (CEF) switching of broadcasting. Some ATM switches might have point-to ATM Forum UNI 3.0 or ATM Forum UNI 3.1, depending on demand. The router performs as the user and the LAN interconnection device at the user-network interface (UNI). Configuring the Cisco NM-1A-T3/E3 Network Module Information About the Cisco ATM T3/E3 Network Module - Flow must be explicitly enabled...
... IP packets • Flow, and Cisco Express Forwarding (CEF) switching of broadcasting. Some ATM switches might have point-to ATM Forum UNI 3.0 or ATM Forum UNI 3.1, depending on demand. The router performs as the user and the LAN interconnection device at the user-network interface (UNI). Configuring the Cisco NM-1A-T3/E3 Network Module Information About the Cisco ATM T3/E3 Network Module - Flow must be explicitly enabled...
User Guide
Page 4
...UBR+ is 1. card type {t3 | e3} slot Cisco IOS Release 12.4(15)T 4 The ATM T3/E3 network module supports four classes of 2. VBR has the second highest transport priority, which is configured. Traffic categorized as voice and video. Note The ATM T3/E3 network module will not be operational until a card type is 0. configure terminal 3. enable 2. VBR ...per SVC). UBR is available in non-real-time (VBR-nrt) and real-time (VBR-rt). SUMMARY STEPS 1. How to Configure the ATM T3/E3 Network Module Configuring the Cisco NM-1A-T3/E3 Network Module Classes of 3.
...UBR+ is 1. card type {t3 | e3} slot Cisco IOS Release 12.4(15)T 4 The ATM T3/E3 network module supports four classes of 2. VBR has the second highest transport priority, which is configured. Traffic categorized as voice and video. Note The ATM T3/E3 network module will not be operational until a card type is 0. configure terminal 3. enable 2. VBR ...per SVC). UBR is available in non-real-time (VBR-nrt) and real-time (VBR-rt). SUMMARY STEPS 1. How to Configure the ATM T3/E3 Network Module Configuring the Cisco NM-1A-T3/E3 Network Module Classes of 3.
User Guide
Page 5
.... Changing the Card Type To change the ATM T3/E3 network module for the ATM T3/E3 network module. reload Cisco IOS Release 12.4(15)T 5 Configuring the Cisco NM-1A-T3/E3 Network Module How to Configure the ATM T3/E3 Network Module DETAILED STEPS Command or Action Step 1 enable Step 2 Example: Router> enable configure terminal Step 3 Example: Router# configure terminal card type {t3|e3} slot Example: Router(config)# card type t3 1 Purpose Enables privileged EXEC mode. • Enter your...
.... Changing the Card Type To change the ATM T3/E3 network module for the ATM T3/E3 network module. reload Cisco IOS Release 12.4(15)T 5 Configuring the Cisco NM-1A-T3/E3 Network Module How to Configure the ATM T3/E3 Network Module DETAILED STEPS Command or Action Step 1 enable Step 2 Example: Router> enable configure terminal Step 3 Example: Router# configure terminal card type {t3|e3} slot Example: Router(config)# card type t3 1 Purpose Enables privileged EXEC mode. • Enter your...
User Guide
Page 6
... or less. The Cisco IOS software will be changed from T3 to Configure the ATM T3/E3 Network Module Configuring the Cisco NM-1A-T3/E3 Network Module DETAILED STEPS Command or Action Step 1 enable Step 2 Example: Router> enable configure terminal Step 3 Example: Router# configure terminal no card type {t3 | e3} Step 4 Example: Router(config)# no card type t3 card type {t3 | e3} slot Step 5 Example: Router(config)# card type t3 1 reload Example: Router...
... or less. The Cisco IOS software will be changed from T3 to Configure the ATM T3/E3 Network Module Configuring the Cisco NM-1A-T3/E3 Network Module DETAILED STEPS Command or Action Step 1 enable Step 2 Example: Router> enable configure terminal Step 3 Example: Router# configure terminal no card type {t3 | e3} Step 4 Example: Router(config)# no card type t3 card type {t3 | e3} slot Step 5 Example: Router(config)# card type t3 1 reload Example: Router...
User Guide
Page 7
... otherwise. Default source is removed from either configuration. Configuring the Cisco NM-1A-T3/E3 Network Module How to Configure the ATM T3/E3 Network Module Enabling the ATM Interface To enable the ATM T3/E3 interface, perform the following tasks, starting in global configuration mode. no shutdown Mandatory if the ATM port the network module is enabled by default. The ATM interface is connected to a PVC • Configuring the AAL and Encapsulation Type •...
... otherwise. Default source is removed from either configuration. Configuring the Cisco NM-1A-T3/E3 Network Module How to Configure the ATM T3/E3 Network Module Enabling the ATM Interface To enable the ATM T3/E3 interface, perform the following tasks, starting in global configuration mode. no shutdown Mandatory if the ATM port the network module is enabled by default. The ATM interface is connected to a PVC • Configuring the AAL and Encapsulation Type •...
User Guide
Page 8
....34.237 broadcast Note If you can reenter the interface-ATM-VC configuration mode by simply entering pvc name. How to Configure the ATM T3/E3 Network Module Configuring the Cisco NM-1A-T3/E3 Network Module Creating a PVC To create a PVC on a PVC by using the protocol command, this broadcasting configuration will take precedence over any direct configuration made using the broadcast command. This section describes how...
....34.237 broadcast Note If you can reenter the interface-ATM-VC configuration mode by simply entering pvc name. How to Configure the ATM T3/E3 Network Module Configuring the Cisco NM-1A-T3/E3 Network Module Creating a PVC To create a PVC on a PVC by using the protocol command, this broadcasting configuration will take precedence over any direct configuration made using the broadcast command. This section describes how...
User Guide
Page 9
...)# abr 10000 3000 Router(config-if-atm-vc)# ubr output-pcr Configures UBR. Configuring the Cisco NM-1A-T3/E3 Network Module How to Configure the ATM T3/E3 Network Module Configuring the AAL and Encapsulation Type To configure the ATM adaptation layer (AAL) and encapsulation type on a VC, use the following command, beginning in interface-ATM-VC configuration mode: Command Router(config-if-atm-vc)# encapsulation {aal2 | aal5auto | aal5autoppp virtual-template...
...)# abr 10000 3000 Router(config-if-atm-vc)# ubr output-pcr Configures UBR. Configuring the Cisco NM-1A-T3/E3 Network Module How to Configure the ATM T3/E3 Network Module Configuring the AAL and Encapsulation Type To configure the ATM adaptation layer (AAL) and encapsulation type on a VC, use the following command, beginning in interface-ATM-VC configuration mode: Command Router(config-if-atm-vc)# encapsulation {aal2 | aal5auto | aal5autoppp virtual-template...
User Guide
Page 10
... arguments are in number of cells. Example: Router(config-if-atm-vc)# vbr-rt 10000 3000 64 Router(config-if-atm-vc)# cbr rate Configures CBR. How to Configure the ATM T3/E3 Network Module Configuring the Cisco NM-1A-T3/E3 Network Module Command Router(config-if-atm-vc)# vbr-rt peak-rate average-rate burst Purpose Configures real-time VBR. The default rate increase factor is 16.
... arguments are in number of cells. Example: Router(config-if-atm-vc)# vbr-rt 10000 3000 64 Router(config-if-atm-vc)# cbr rate Configures CBR. How to Configure the ATM T3/E3 Network Module Configuring the Cisco NM-1A-T3/E3 Network Module Command Router(config-if-atm-vc)# vbr-rt peak-rate average-rate burst Purpose Configures real-time VBR. The default rate increase factor is 16.
User Guide
Page 11
... with the ILMI In an SVC environment, you can receive simple network management protocol (SNMP) traps and new network prefixes. Configuring the Cisco NM-1A-T3/E3 Network Module SVCs SVCs To use the following command in interface configuration mode: Command Router(config-if)# atm ilmi-keepalive [seconds] Example: Router(config-if)# atm ilmi-keepalive 6 Purpose Enables ILMI keepalives and sets the interval...
... with the ILMI In an SVC environment, you can receive simple network management protocol (SNMP) traps and new network prefixes. Configuring the Cisco NM-1A-T3/E3 Network Module SVCs SVCs To use the following command in interface configuration mode: Command Router(config-if)# atm ilmi-keepalive [seconds] Example: Router(config-if)# atm ilmi-keepalive 6 Purpose Enables ILMI keepalives and sets the interval...
User Guide
Page 12
... Q.2931 protocol. The signaling that uses SVCs. The VPI and VCI values must be configured before any SVCs can be configured consistently with each other. This is used to router. SVCs Configuring the Cisco NM-1A-T3/E3 Network Module Configuring the PVC That Performs SVC Call Setup ATM uses out-of -band signaling, a signaling PVC must be set up only on...
... Q.2931 protocol. The signaling that uses SVCs. The VPI and VCI values must be configured before any SVCs can be configured consistently with each other. This is used to router. SVCs Configuring the Cisco NM-1A-T3/E3 Network Module Configuring the PVC That Performs SVC Call Setup ATM uses out-of -band signaling, a signaling PVC must be set up only on...
User Guide
Page 13
... a PVC for communication with the switch via ILMI, you to configure the ATM address by entering the ESI (12 hexadecimal characters) and the selector byte (2 hexadecimal characters). Configuring the Cisco NM-1A-T3/E3 Network Module SVCs Configuring the NSAP Address Every ATM interface involved with signaling must be configured with a network service access point (NSAP) address. exit 3. The NSAP prefix (26 hexadecimal characters...
... a PVC for communication with the switch via ILMI, you to configure the ATM address by entering the ESI (12 hexadecimal characters) and the selector byte (2 hexadecimal characters). Configuring the Cisco NM-1A-T3/E3 Network Module SVCs Configuring the NSAP Address Every ATM interface involved with signaling must be configured with a network service access point (NSAP) address. exit 3. The NSAP prefix (26 hexadecimal characters...
User Guide
Page 14
...(config-if-atm-vc)# protocol ip Once you specify a name for an SVC, you can remove an SVC configuration by entering the svc name command. For a list of AAL types and encapsulations, see the section "Configuring the AAL and Encapsulation Type". encapsulation aal5encap 3. Cisco IOS Release 12.4(15)T 14 SVCs Configuring the Cisco NM-1A-T3/E3 Network Module Creating an SVC...
...(config-if-atm-vc)# protocol ip Once you specify a name for an SVC, you can remove an SVC configuration by entering the svc name command. For a list of AAL types and encapsulations, see the section "Configuring the AAL and Encapsulation Type". encapsulation aal5encap 3. Cisco IOS Release 12.4(15)T 14 SVCs Configuring the Cisco NM-1A-T3/E3 Network Module Creating an SVC...
User Guide
Page 15
... the following command in interface configuration mode. The default T3 ATM framing type is g832.adm. Example: Router(config-if)# atm framing cbitadm To configure E3 ATM framing on the ATM T3/E3 network module. Note G751adm framing is configured as a T3 connection or an E3 connection. Configures E3 ATM framing type The default E3 ATM framing type is cbitplcp. Configuring the Cisco NM-1A-T3/E3 Network Module Customizing the ATM T3/E3 Network Module Customizing the ATM T3/E3 Network Module You can customize have default...
... the following command in interface configuration mode. The default T3 ATM framing type is g832.adm. Example: Router(config-if)# atm framing cbitadm To configure E3 ATM framing on the ATM T3/E3 network module. Note G751adm framing is configured as a T3 connection or an E3 connection. Configures E3 ATM framing type The default E3 ATM framing type is cbitplcp. Configuring the Cisco NM-1A-T3/E3 Network Module Customizing the ATM T3/E3 Network Module Customizing the ATM T3/E3 Network Module You can customize have default...
User Guide
Page 16
.../5 10/5 10/5 20/20 10/5 10/5 10/5 10/5 20/20 Cisco IOS Release 12.4(15)T 16 Configuration Example Configuring the Cisco NM-1A-T3/E3 Network Module Setting the Loopback Mode To loop all packets back to your ATM interface instead of to the network, use the following command in interface configuration mode: Command Router(config-if)# loopback line Purpose Sets line loopback...
.../5 10/5 10/5 20/20 10/5 10/5 10/5 10/5 20/20 Cisco IOS Release 12.4(15)T 16 Configuration Example Configuring the Cisco NM-1A-T3/E3 Network Module Setting the Loopback Mode To loop all packets back to your ATM interface instead of to the network, use the following command in interface configuration mode: Command Router(config-if)# loopback line Purpose Sets line loopback...
User Guide
Page 17
... rates were used: 150 for 1 Mbps; 300 for 2 Mbps; 750 for 5 Mbps; For 1400 bytes data traffic from IXIA; Cisco IOS Release 12.4(15)T 17 and 1500 for 10 Mbps • IXIA was used for pumping UDP bi-directional unicast streams for 5 ...and 1400 bytes: - and 3500 for continuous burst on two to ATM cell conversion overhead. • 64B frame size IXIA traffic streams includes CRC. Configuring the Cisco NM-1A-T3/E3 Network Module Recommendations for Watermark Settings Traffic Pattern • The following pageant configuration was used in bi-directional way for 10 Mbps -
... rates were used: 150 for 1 Mbps; 300 for 2 Mbps; 750 for 5 Mbps; For 1400 bytes data traffic from IXIA; Cisco IOS Release 12.4(15)T 17 and 1500 for 10 Mbps • IXIA was used for pumping UDP bi-directional unicast streams for 5 ...and 1400 bytes: - and 3500 for continuous burst on two to ATM cell conversion overhead. • 64B frame size IXIA traffic streams includes CRC. Configuring the Cisco NM-1A-T3/E3 Network Module Recommendations for Watermark Settings Traffic Pattern • The following pageant configuration was used in bi-directional way for 10 Mbps -
User Guide
Page 18
Recommendations for Watermark Settings Configuring the Cisco NM-1A-T3/E3 Network Module Example of the Router Configuration Used for the watermark testing. policy-map Child_Map3 class COSP_NBIP_LABS_TC1_EF police cir 5000000 bc 625000 conform-action set-dscp-transmit...255.255.0 load-interval 30 duplex auto speed auto media-type rj45 ! Cisco IOS Release 12.4(15)T 18 Table 2 Example of the Router Configuration Used for Watermark Testing The following example provides the router configuration that was used for Watermark Testing UUT1 (3845) class-map match-any COSQ_NBIP_LABS_TC1_COS4...
Recommendations for Watermark Settings Configuring the Cisco NM-1A-T3/E3 Network Module Example of the Router Configuration Used for the watermark testing. policy-map Child_Map3 class COSP_NBIP_LABS_TC1_EF police cir 5000000 bc 625000 conform-action set-dscp-transmit...255.255.0 load-interval 30 duplex auto speed auto media-type rj45 ! Cisco IOS Release 12.4(15)T 18 Table 2 Example of the Router Configuration Used for Watermark Testing The following example provides the router configuration that was used for Watermark Testing UUT1 (3845) class-map match-any COSQ_NBIP_LABS_TC1_COS4...
User Guide
Page 19
....0 195.18.18.1 ! ! ip http server no ip http secure-server ! interface ATM1/0.1 point-to the ATM T3/E3 network module. ip access-list extended EF_APP_IPV4_TC1 permit udp any eq 5060 any permit udp any any eq 5060 deny ip any 110...5000 no ip address ip virtual-reassembly load-interval 30 atm scrambling cell-payload no atm ilmi-keepalive ! Configuring the Cisco NM-1A-T3/E3 Network Module Additional References Table 2 Example of network modules Document Title Cisco Network Modules Hardware Installation Guide Cisco IOS Release 12.4(15)T 19 ip access-list extended ...
....0 195.18.18.1 ! ! ip http server no ip http secure-server ! interface ATM1/0.1 point-to the ATM T3/E3 network module. ip access-list extended EF_APP_IPV4_TC1 permit udp any eq 5060 any permit udp any any eq 5060 deny ip any 110...5000 no ip address ip virtual-reassembly load-interval 30 atm scrambling cell-payload no atm ilmi-keepalive ! Configuring the Cisco NM-1A-T3/E3 Network Module Additional References Table 2 Example of network modules Document Title Cisco Network Modules Hardware Installation Guide Cisco IOS Release 12.4(15)T 19 ip access-list extended ...
User Guide
Page 20
...Access to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Cisco IOS Release 12.4(15)T 20 feature, and support for existing RFCs have not been modified by...following URL: http://www.cisco.com/go/mibs RFCs RFC Title No new or modified RFCs are supported by this feature, and support for troubleshooting and resolving technical issues with Cisco products and technologies. Additional References Configuring the Cisco NM-1A-T3/E3 Network Module Standards Standard Title No ...
...Access to various services, such as the Product Alert Tool (accessed from Field Notices), the Cisco Technical Services Newsletter, and Really Simple Syndication (RSS) Feeds. Cisco IOS Release 12.4(15)T 20 feature, and support for existing RFCs have not been modified by...following URL: http://www.cisco.com/go/mibs RFCs RFC Title No new or modified RFCs are supported by this feature, and support for troubleshooting and resolving technical issues with Cisco products and technologies. Additional References Configuring the Cisco NM-1A-T3/E3 Network Module Standards Standard Title No ...